An uncovered basement window well is a magnet for leaves, rain, small animals, and the occasional lost baseball, all of which end up piled against the glass. A diy window well cover solves every one of those problems for a fraction of what a custom fabricator charges, and you can build one in an afternoon with basic tools. The trick to a great diy window well cover is matching the material to your goal, whether that is maximum light, snow-load strength, or a fully sealed barrier against water intrusion.
Part of our Windows & Doors guide — explore the full guide →
Below are three build paths, from a simple polycarbonate lid to a hinged metal grate, plus the measuring and mounting details that make any of them fit like it was made for your well.
- Decide What the Cover Needs to Do
- Material Options and What They Cost
- Measure the Well Correctly
- Build 1: Sloped Polycarbonate Lid
- Build 2: Hinged Steel Grate for Fall Protection
- Build 3: Budget Wood-and-Wire Cover
- Mounting, Sealing, and Maintenance
- Handling Snow Load in Cold Climates
- Meeting Egress and Safety Codes
- Buying Basement Window Well Covers: Prefab Options vs. DIY
Decide What the Cover Needs to Do
Before buying material, be honest about the job. A cover that keeps out leaves and rodents is different from one meant to shed heavy snow or stop water from a downspout. Ask yourself three questions: Does the well flood in hard rain? Do kids or pets play near it and risk falling in? How much natural light do you want to preserve in the basement room below?
Egress windows, the code-required escape openings in finished basement bedrooms, add a critical rule: the cover must open from the inside without tools, keys, or special knowledge. Never permanently fasten a cover over an egress window. For those, a hinged or lift-off design is mandatory.
It also pays to think about how the cover interacts with your drainage. A window well is essentially a small pit against the foundation, and it depends on a gravel base and, ideally, a drain to shed the water that collects in it. A solid cover that keeps rain out reduces the load on that drainage entirely, while an open grate lets everything through and relies on the well drainage to keep up. Knowing whether your well drains well or tends to hold water should steer you toward a sealed lid over a foundation prone to seepage, and toward an open grate where drainage is excellent and fall protection is the only real concern.
Material Options and What They Cost
- Clear polycarbonate sheet (Lexan): Nearly unbreakable, lets light through, and sheds water. A 4-by-8 sheet of 1/4-inch polycarbonate runs $80 to $160. Ideal for a sealed, light-preserving lid.
- Acrylic (Plexiglas): Cheaper and clear but more brittle in cold; better for mild climates.
- Galvanized or expanded steel grate: Strong and secure, great for fall protection, but does not block rain. A hardware-cloth or grate build costs $40 to $90.
- Treated lumber frame with hardware cloth: The budget option at $30 to $60, good for keeping debris and animals out while venting fully.
For most homeowners who want light plus weather protection, a polycarbonate lid on a simple frame is the sweet spot.
Measure the Well Correctly
Accurate measurements are everything. For a standard semicircular well, measure the straight back length against the foundation and the maximum projection out from the wall. For rectangular or square wells, measure length and width, then add 2 to 3 inches of overhang on each exposed side so the cover sheds water past the well lip rather than into it.
Note the well height too, and check whether the top edge of the well liner sits flush with grade or stands proud. That determines how your cover mounts and whether you need a sloped design to drain water away from the foundation.
Build 1: Sloped Polycarbonate Lid
This design vents light, keeps water out, and drains rain away from the house.
- Build a frame from 1-by-3 or 2-by-2 treated lumber (or aluminum angle) sized to overhang the well by 2 inches all around.
- Make the back edge, against the foundation, taller than the front by 2 to 3 inches so the finished lid slopes outward and drains away from the wall.
- Cut the polycarbonate sheet to cover the frame with a slight overhang. Score and snap thinner sheets, or use a fine-tooth blade for thicker stock.
- Pre-drill oversized holes in the polycarbonate to allow for thermal expansion, then fasten it to the frame with washer-head screws and rubber washers.
- Add a strip of weatherstripping foam along the underside edges where the frame meets the well lip to seal out wind-driven rain.
Secure the finished lid with two barrel bolts or a couple of anchored eye hooks so wind cannot lift it, but keep the connection removable for egress wells.
Build 2: Hinged Steel Grate for Fall Protection
If safety is the priority and you do not mind rain passing through, a metal grate is the strongest, most secure choice.
- Cut a section of expanded metal or heavy welded grate to the well footprint plus a small overhang.
- Frame the perimeter with steel angle for rigidity, welding or bolting the corners.
- Attach two heavy hinges along the foundation side so the grate lifts up and out for egress.
- Anchor the hinge side to the foundation or well liner with masonry screws.
- Add a simple latch on the outer edge that a person inside can release, but that resists being flipped open from above.
A grate like this can support a person’s weight when built from proper stock, satisfying fall-protection concerns near walkways.
Build 3: Budget Wood-and-Wire Cover
For a quick debris-and-critter barrier, build a treated 1-by-2 frame to the well dimensions and staple 1/4-inch galvanized hardware cloth across it. Cap the staples with a thin trim strip so the wire cannot pull free. It will not stop rain, but it keeps out leaves, mice, chipmunks, and toads for under $60. Rest it on the well lip and weigh it down or clip it in place.
Mounting, Sealing, and Maintenance
However you build it, the cover should never trap water against the foundation. Slope it outward, keep drainage gravel in the bottom of the well clear, and check that your gutter downspouts discharge well away from the window. A cover over a well that still fills with water simply hides a drainage problem you will eventually pay to fix.
Inspect the cover each spring and fall. Clear leaves off the top, re-tighten fasteners, and refresh weatherstripping if it has flattened. Polycarbonate can be cleaned with mild soap and water; avoid ammonia glass cleaners, which cloud the plastic over time.
Handling Snow Load in Cold Climates
If you live where winters bring heavy snow, the cover has to carry more than its own weight. Wet snow weighs roughly 12 to 20 pounds per cubic foot, so even a few inches piled on a 3-by-4-foot cover can add 60 pounds or more. A flat polycarbonate lid unsupported in the middle will sag or crack under that load. Build a center support rib from a length of aluminum angle or treated 2×2 running front to back, and step up to 1/4-inch or thicker polycarbonate rather than thin acrylic.
The slope you built for drainage helps here too, since a pitched cover sheds snow more readily than a flat one. Clear accumulation after big storms rather than letting it pile up and refreeze, which can bond the cover to the well and make egress impossible. For metal grates, snow load is rarely an issue, but ice can still form a sheet across the openings, so knock it clear where the cover protects an escape window.
Meeting Egress and Safety Codes
Any basement bedroom or finished habitable room is required by most building codes to have an egress window, a code-defined escape opening large enough for a person to climb out and for a firefighter in full gear to climb in. The minimum net clear opening is typically 5.7 square feet, with a minimum height of 24 inches and width of 20 inches, and the sill no more than 44 inches above the floor. A cover over that window must be releasable from inside without keys, tools, or special knowledge.
That rule shapes your design absolutely. A hinged lid a person can push open from below, or a lift-off panel light enough for a child to move, both satisfy it. A cover fastened down with screws does not, no matter how well it sheds water. If your window well serves an egress window, test that a person inside can open the cover quickly and unassisted before you consider the job finished. When in doubt, check with your local building department, since egress requirements are strictly enforced during inspections and home sales.
A well-built cover pays for itself the first storm it keeps out of your basement, and because you sized and shaped it yourself, it fits far better than any generic bubble dome off the shelf. Spend the extra thirty minutes on the slope and the seal, and it will protect that window for a decade.
Buying Basement Window Well Covers: Prefab Options vs. DIY
Not everyone wants to build from scratch, and ready-made basement window well covers have improved a lot. Knowing what is on the market, what it costs, and where it falls short helps you decide whether to buy, build, or combine the two by buying a prefab lid and adding your own supports and latches.
Common Prefab Cover Types
- Bubble or dome covers: Molded clear or tinted plastic with a raised profile that sheds water and snow. Typically $30 to $120 for standard semicircular wells. Affordable and easy, but the thinnest versions are not designed to hold a person’s weight and can yellow or crack after several years of sun.
- Flat polycarbonate covers: Rigid clear lids, often with an aluminum or steel frame, in the $100 to $300 range. Better light transmission and a cleaner look, and some are rated for a specific load.
- Steel grate covers: Galvanized or powder-coated grates for fall protection, usually $100 to $350. Many are sold as egress-compatible with hinged or lift-off designs.
- Custom-fabricated covers: Made to your exact measurements with polycarbonate over steel, commonly $250 to $700 or more per well installed. The best fit for oversized, stepped, or rectangular egress wells.
These are typical retail ranges; prices vary by size, region, and whether installation is included.
What to Check Before You Buy
Fit is the most common failure. Prefab covers are sized by well width and projection, so use the same measurements described earlier and compare them against the manufacturer’s sizing chart, not just the product name. A cover that is too small drops inside the well lip and funnels water toward the glass. Look for a stated load rating if children, pets, or foot traffic are nearby; “decorative” or “debris” covers are not the same as fall-protection covers. Check that mounting hardware suits your liner, since corrugated steel, composite, and concrete wells all fasten differently.
When a Hybrid Approach Wins
A common and cost-effective middle path is to buy a quality polycarbonate or dome lid and upgrade it yourself with a center support rib for snow, foam weatherstripping along the edges, and removable clips instead of permanent screws. That combination often costs less than a custom unit while performing better than an off-the-shelf lid alone.
Egress Wells Need Extra Care
If the well serves a basement bedroom’s escape window, confirm that any cover you buy can be opened from inside by an adult or older child without tools and without excessive force, including when snow sits on top. Some jurisdictions have specific rules for covers over egress wells. If you are unsure whether a cover meets local code, or if the window itself needs enlarging to qualify as egress, talk to your building department or a licensed contractor before installing it.