An electric dryer that tumbles for an hour and hands back damp, cool towels usually has one burned-out part hiding behind the back panel. When the dryer heating element not working is the cause, the drum spins and the timer runs, but the coil of nichrome wire that should glow red has a break in it. The good part is that this is one of the most approachable appliance repairs: the element is a single replaceable part, the test needs only a basic multimeter, and the whole job usually takes an hour or two.
The short answer: unplug the dryer, remove the rear or front access panel, look for a visible break in the coil, and run a continuity test across the element’s two terminals. No continuity means the element is open and must be replaced. Because elements often fail when airflow is restricted, check the thermal fuse and the vent at the same time, or the new coil may burn out just as fast.
- Dryer Heating Element Not Working: Confirm the Symptoms First
- Safety Before You Open the Cabinet
- Tools and Materials
- How to Test and Replace the Element
- 1. Find your model number and element location
- 2. Pull the dryer out and remove the access panel
- 3. Inspect the coil visually
- 4. Run the continuity test
- 5. Test the thermal fuse and high-limit thermostat
- 6. Remove the old element
- 7. Install the new element
- 8. Clean the vent and lint path
- 9. Reassemble and test
- Troubleshooting After the Repair
- Cost of Dryer Heating Element Repair
- When to Call a Pro
- Frequently Asked Questions
One note before any work: this repair applies to electric dryers only. Gas dryers use an igniter, flame sensor and gas valve coils instead of an element, and anything involving the gas burner or gas line belongs to a licensed technician. If you ever smell gas, leave the house and call your gas utility from outside.
Dryer Heating Element Not Working: Confirm the Symptoms First
A failed element produces a specific pattern. The dryer starts, the drum turns, the timer or electronic countdown advances, and the air coming out of the vent outside is cool or barely warm. Clothes come out damp after a full cycle. If the dryer does not start at all, or the drum will not turn, the problem is elsewhere, usually the door switch, thermal fuse on some models, belt or motor.
Other causes can mimic a bad element, so keep them in mind:
- Tripped breaker leg: electric dryers run on a 240-volt circuit with a double-pole breaker. If one half trips, the motor may still run on 120 volts while the heater gets nothing. Reset the breaker fully off, then on.
- Blown thermal fuse or high-limit thermostat: these safety parts cut heat when the dryer overheats, often because of a clogged vent.
- Failed cycling thermostat: it regulates temperature and can stick open.
- Control board or timer fault: less common, and worth suspecting only after the simpler parts test good.
If you check dryer heating element continuity and it passes, move on to these components with the same unplugged continuity method.
Safety Before You Open the Cabinet
Unplug the dryer from the wall. The 240-volt receptacle carries enough current to cause serious injury, so pulling the plug is mandatory, not optional. If the dryer is hardwired or the plug is hard to reach, switch off its double-pole breaker and confirm the power is off with a non-contact voltage tester at the cord. Never test voltage on a powered dryer and never run the dryer with panels removed. All checks in this repair are resistance or continuity readings taken with the appliance unplugged.
Wear gloves, because sheet metal edges inside the cabinet are sharp. Let the dryer cool for at least 30 minutes if it was just running. Keep a phone handy to photograph wire positions before you disconnect anything.
Tools and Materials
- Digital multimeter with a resistance (ohms) or continuity setting
- Nut drivers (1/4-inch and 5/16-inch are common) and a Phillips screwdriver
- Putty knife for releasing top panel clips on some models
- Needle-nose pliers for wire terminals
- Work gloves and a flashlight
- Replacement dryer heating element matched to your model number
- Replacement thermal fuse and high-limit thermostat if they test open
- Vacuum with a crevice tool and a vent cleaning brush
How to Test and Replace the Element
1. Find your model number and element location
The model tag is usually inside the door opening, on the back panel or under the lid. Look up the parts diagram for your model. On many dryers the element sits in a metal housing behind the rear access panel. On others it is reached by removing the front panel and drum. Knowing which design you have saves a lot of unnecessary disassembly.
2. Pull the dryer out and remove the access panel
Slide the dryer away from the wall carefully so you do not crush the vent duct or strain the cord. Disconnect the vent duct from the back. Remove the screws holding the rear panel, or for front-access designs, release the top, remove the front panel and lift out the drum after slipping the belt off the motor pulley.
3. Inspect the coil visually
Shine a flashlight into the element housing. A healthy coil is continuous, evenly spaced and held by ceramic insulators. A failed coil often shows a clear gap, a blob of melted wire, or a section that has sagged and touched the housing. A visible break is enough to condemn the part, but test it anyway to be sure.
4. Run the continuity test
Photograph the wiring, then pull both wires off the element terminals. Set the multimeter to the lowest ohms range or to continuity. Touch one probe to each terminal. A good element typically reads somewhere around 7 to 12 ohms, depending on the design. A reading of OL, infinity or no beep means the circuit is open and the element is dead. Also touch one probe to a terminal and the other to the metal housing: there should be no continuity there. If there is, the coil is shorted to ground and must be replaced.
5. Test the thermal fuse and high-limit thermostat
These small parts are mounted on or near the heater housing and blower. Disconnect each and check for continuity across its terminals. Both should read near zero ohms at room temperature. An open thermal fuse is a warning sign: it blew because the dryer overheated, almost always due to a lint-clogged vent or a crushed duct. Replace any part that tests open.
6. Remove the old element
Unscrew the element housing from the cabinet, slide it out, and remove the screws or tabs holding the coil assembly. Some elements come as a complete housing, while others are a coil kit you thread onto the existing ceramic insulators. Housing-style replacements are faster and less fiddly for a first-time repair.
7. Install the new element
Set the new element into place, secure the housing, and reconnect the wires exactly as they appeared in your photo. Make sure the terminals are snug, since loose connections create heat and can scorch wires. Replace the thermal fuse or limit thermostat if needed. Check that no wire touches the hot housing or rubs against a sharp edge.
8. Clean the vent and lint path
While the dryer is open, vacuum lint from the cabinet floor, the blower housing and around the element. Then clean the entire vent run to the outside. A restricted vent is the leading reason elements and thermal fuses fail early, and lint buildup is a well-known dryer fire hazard. Replace flimsy plastic or foil accordion duct with rigid or semi-rigid metal duct, and keep the run as short and straight as practical.
9. Reassemble and test
Reinstall panels, reconnect the vent duct, push the dryer back without kinking the duct, and plug it in. Run a timed dry cycle on high heat for a few minutes and feel the air at the outside vent hood. It should be noticeably warm within two to three minutes.
Troubleshooting After the Repair
A dryer heating element not working after replacement usually points to a second failed part or an airflow problem rather than a bad new coil.
- Still no heat with a new element: recheck the thermal fuse, high-limit and cycling thermostat, then confirm both breaker legs are on.
- Heat for a few minutes then cool: the cycling thermostat or a restricted vent is cutting heat early.
- New element burned out within weeks: airflow problem. Inspect the vent hood flap, duct length and lint screen housing.
- Burning smell on first run: a little odor from manufacturing residue is normal for a few minutes. A strong or persistent smell means stop, unplug, and inspect for lint near the element or a loose wire.
- Breaker trips when heat engages: possible grounded element or damaged wiring. Unplug and call a technician.
Cost of Dryer Heating Element Repair
A replacement element generally costs $25 to $80 depending on the design, and a thermal fuse or limit thermostat adds roughly $10 to $30. A basic multimeter is around $20 to $40 if you do not own one. Hiring an appliance technician for the same dryer heating element repair usually totals $150 to $300 with labor. Professional vent cleaning commonly runs about $100 to $200, and it is worth doing if your duct run is long or hard to reach.
When to Call a Pro
Call an appliance technician if the element tests good and the safety parts pass but the dryer still will not heat, since that points toward controls or wiring. Get help if you find scorched wires, melted terminals or a burned receptacle, or if the breaker trips repeatedly. Problems with the 240-volt outlet or circuit belong to a licensed electrician, and the dryer should always plug directly into its own receptacle, never into an extension cord or adapter. Gas dryer heating problems go to a licensed technician without exception.
Frequently Asked Questions
How do I know if my dryer heating element is bad?
The drum turns and the timer runs, but the air stays cool and clothes come out damp. With the dryer unplugged, a continuity test across the element terminals that shows no continuity confirms the element is open.
What should a dryer heating element read on a multimeter?
Most read roughly 7 to 12 ohms across the two terminals. An infinite or OL reading means a break in the coil. Any continuity between a terminal and the metal housing means a short.
Why do dryer heating elements burn out?
Restricted airflow is the most common reason. Lint-clogged vents, crushed ducts and blocked vent hoods trap heat around the coil until it fails. Age and frequent high-heat cycles also wear them out.
Should I replace the thermal fuse with the heating element?
Test it, and replace it if it is open. Many technicians replace both at once because an element failure often coincides with an overheating event that also strained the fuse.
Is it worth fixing a dryer heating element?
Usually yes. The part is inexpensive and the repair is straightforward on most electric dryers. Replacement makes more sense only if the dryer is very old and has other failing parts like the motor or drum bearings.