Swapping dated knobs and pulls is the single cheapest upgrade that transforms a kitchen, often for under $100. But there is a catch: a hole drilled a quarter inch off is permanent and glaringly obvious. Learning how to install cabinet hardware correctly is really about measuring and drilling with precision, and a simple template turns that intimidating step into a repeatable, foolproof process. With the right approach, you can update every door and drawer in an afternoon.
Part of our Kitchen Remodeling guide — explore the full guide →
Tools and Materials You Need
Gather everything before you drill the first hole.
- Cabinet hardware jig or template: The single most important tool for accuracy.
- Power drill and sharp bits: Usually a 3/16-inch bit for standard hardware screws.
- Tape measure and pencil: For layout and marking.
- Screwdriver: To drive the mounting screws.
- Painter’s tape and a scrap block: To prevent tear-out on the back of the door.
Buy your knobs and pulls first so you can confirm screw spacing, called center-to-center on pulls, before setting up the jig.
Deciding on Placement
Consistent placement is what makes an installation look professional. Standard conventions give a reliable starting point.
- Door knobs: Placed on the stile opposite the hinges, 2.5 to 3 inches from the corner.
- Door pulls: Mounted vertically on upper cabinets and lower cabinets, aligned with the door corner.
- Drawer knobs: Centered horizontally and vertically on the drawer face.
- Drawer pulls: Centered horizontally; on wide drawers, center them or use two pulls.
For Shaker doors, many installers center hardware on the corner of the flat frame where it meets the raised or recessed panel, which creates a clean, uniform line.
Using a Hardware Template
A template, or jig, is a plastic guide with adjustable pins and holes that positions every piece identically. It pays for itself on the first project by preventing a single ruined door.
Setup Steps
- Set the jig’s edge stops to your chosen distance from the door edge.
- Select the hole spacing that matches your knob or pull.
- Clamp or hold the jig firmly against the door corner.
- Drill through the guide holes using the recommended bit.
Because the jig references the door corner, every knob lands in exactly the same spot without measuring each door individually.
Drilling Clean Holes
A blowout on the back of the door face is the most common mistake. Prevent it by backing the wood.
Place a scrap block of wood tight against the back of the door where the bit will exit, then drill through the front into the block. This supports the wood fibers so they cannot splinter. Apply a strip of painter’s tape over the drill spot on the front as well, which reduces surface chipping on painted or laminate doors.
Drill at full speed with steady, moderate pressure, letting the bit do the work. Forcing a dull bit causes tear-out and wandering holes.
Handling Pulls with Two Holes
Pulls require two perfectly spaced holes, and this is where the center-to-center measurement matters. Measure the distance between the pull’s screw posts, then set your jig to that exact spacing. A pull that is even 1/16 inch off will not seat and can crack the finish if you force the screws.
For long pulls on wide drawers, use the jig’s centering feature or measure carefully from both ends so the pull sits dead center and level.
Mounting the Hardware
With the holes drilled, installation is quick. Feed the machine screw through the back of the door or drawer and thread it into the knob or pull from the front. Standard screws are 8-32 thread; if a screw is too short for a thick door, buy longer replacements at any hardware store.
Tighten by hand first, then snug with a screwdriver. Avoid overtightening, which can strip the threads or dimple a soft wood face.
Working Without a Jig
If you are installing only a few pieces and do not want to buy a template, you can lay them out by hand with care. Make a simple guide from a scrap of cardboard or thin plywood by drilling your reference holes into it, then clamp that shop-made jig to each door in the same position. It is not as fast as a store-bought template, but it guarantees consistency across every door.
For a single knob, measure from both the bottom and the side of the stile and mark the intersection with a center punch, which keeps the drill bit from wandering. Always dry-fit the knob against the mark before drilling to confirm it looks centered by eye, because a mathematically correct spot can still look off on an unusual door style.
Retrofitting Doors with Existing Holes
Replacing old hardware brings its own challenge: the new pulls rarely match the old hole spacing. Measure the existing center-to-center distance first and shop for pulls with the same spacing, which is the easiest fix.
When you cannot find a match, you have two options. A backplate mounted behind the new knob or pull can cover the old holes while giving you a fresh mounting point. Alternatively, fill the old holes with a two-part wood filler, sand flush, and touch up the finish before drilling new ones. On painted doors this hides well; on stained wood the patch may show, so a backplate is usually the cleaner solution.
Final Checks
Step back and sight down a row of doors to confirm everything lines up. Use a small level on horizontal pulls to catch any that sit crooked. If a hole ended up slightly off, a backplate behind the knob can hide minor errors and add a decorative touch. Master these steps for how to install cabinet hardware and you will have a crisp, uniform result that looks like a professional did the work, at a fraction of the cost.