Comparisons

Inside vs Outside Mount Blinds: Which Fits Your Window?

Inside vs Outside Mount Blinds: Which Fits Your Window?

The choice between inside vs outside mount blinds usually gets made in about five seconds at the order screen, and it causes more returns than any other measuring mistake. An inside mount sits within the window opening for a clean, built-in look. An outside mount covers the opening and attaches to the trim or wall, which blocks more light and hides imperfect frames. Neither one is better everywhere.

The short answer: choose inside mount when the window has enough depth, square corners and attractive trim you want to show off. Choose outside mount when the window is shallow, out of square, has a crank or handle in the way, or when you need maximum darkness. Most of the decision comes down to four checks: depth, squareness, obstructions and light control.

Getting it right also depends on measuring correctly for the method you pick, because the deductions are different. Factories subtract a small amount from inside mount orders, and outside mount orders are made to the exact size you give. Mixing up those rules is how blinds end up too tight to fit or too narrow to cover.

Inside vs Outside Mount Blinds at a Glance

Factor Inside Mount Outside Mount
Look Clean, built-in, shows trim Covers trim, adds bulk
Light gaps Small gaps at the sides Minimal when oversized
Depth needed Often 1.5 to 3 inches Almost none
Out-of-square frames Problematic Forgiving
Window looks True size Can look larger

Check Window Depth First

Depth decides whether an inside mount is even possible. Measure from the inner face of the window frame to the front edge of the opening, at the shallowest point. Each product has two numbers: the minimum depth to mount at all, and the depth needed for a fully recessed (flush) look.

  • Faux wood blinds (2-inch slats): often need about 2.25 to 3 inches for flush mounting. Faux wood blinds inside mount on shallow vinyl replacement windows often stick out.
  • Real wood and aluminum blinds: aluminum mini blinds need as little as 1 inch; wood blinds resemble faux wood.
  • Cellular shades: single-cell styles may mount in about 1 to 1.5 inches; double-cell needs more. Inside mount cellular shades are popular because they need so little room.
  • Roller shades: usually 2 to 3.5 inches depending on fabric roll size.

If the depth falls short of the flush requirement but meets the minimum, the blind will project out of the frame. That can look fine on some windows, but if you want the recessed look, consider a slimmer product or switch to outside mount.

Squareness, Trim and Obstructions

Out-of-Square Openings

Measure the width at the top, middle and bottom, and the height at left, center and right. If the measurements differ by more than about a quarter inch, an inside mount will show tapered gaps or may bind. Also measure diagonals; unequal diagonals confirm the frame is racked. Outside mount hides all of this because the blind covers the irregular opening.

Trim You Want to Show

Beautiful casing, stained trim or a deep stone sill are reasons to go inside. Outside mount covers some or all of that trim. If the trim is plain or worn, covering it is a plus.

Cranks, Handles and Locks

Casement and awning windows have crank handles that stick into the opening. Sliding windows and patio doors may have latches. Inside-mounted slats or a bottom rail can hit these obstructions. Options include choosing a shallower product, installing a crank extension, or going outside mount with spacers that push the headrail away from the frame. Outside mount roller shade installations clear most handles easily.

Light Gaps and Privacy

Inside mounts leave a small gap on each side, often a quarter to a half inch total, because the factory makes the product slightly narrower than the opening so it can operate. That strip of light is minor in a kitchen and annoying in a bedroom. Outside mounts overlap the opening, typically by 1.5 to 3 inches on each side, which reduces the halo dramatically.

For bedrooms and media rooms, outside mount almost always wins for darkness. Cellular blinds outside mount over a frame are a common pick for nurseries because the honeycomb fabric blocks light and the overlap covers the edges. If you love the inside look, you can add light-blocking side strips to the frame.

Making Windows Look Bigger

An outside mount gives you a design trick: mount the headrail several inches higher than the top of the opening and extend wider than the trim. When raised, the blind stacks against the wall over the glass instead of covering it, so the full window shows and the window appears taller. Outside mount faux wood blinds mounted 3 to 6 inches high and 2 to 3 inches wide on each side make small windows feel more generous.

Inside mounts do the opposite: the stack sits in the top of the opening and blocks a few inches of glass. On a short window, that stack can noticeably reduce daylight.

Looking to buy Inside vs Outside Mount Blinds? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

How to Measure for Each Method

Use a steel tape measure, never cloth, and record to the nearest eighth of an inch. Write width first, then height.

Inside Mount Measuring

  1. Measure width inside the opening at top, middle and bottom. Record the narrowest measurement.
  2. Measure height at left, center and right. Record the longest for most blinds (shades can follow the manufacturer’s rule).
  3. Do not make deductions. The factory subtracts roughly a quarter to a half inch from the width for operating clearance.
  4. Measure the depth at the shallowest point and compare it to the product’s minimum.

Outside Mount Measuring

  1. Decide on overlap: typically 1.5 to 3 inches past the opening on each side.
  2. Measure the width of the opening plus the overlap on both sides. Record the exact size you want; the factory will not deduct.
  3. Measure height from where the headrail will mount (often 2 to 3 inches over the opening) to the sill or to 1.5 inches past the bottom of the opening if there is no sill.
  4. Check that the wall or trim face is flat enough for brackets, and that nothing projects into the path, such as a sill horn.

Never mix the two: giving an exact outside measurement for an inside mount order results in a blind that is too wide to fit, and giving an inside measurement on an outside order leaves gaps.

Installation and Ladder Safety

Both methods use brackets screwed into wood. Inside mounts screw up into the top of the frame; outside mounts screw into the trim face or into the wall framing. Use a stud finder for wall mounts on wide blinds, and use proper anchors when a stud is not available.

Use a stable step ladder rated for your weight, set on level ground with the spreaders locked. Keep your hips between the rails, maintain three points of contact, and never stand on the top cap. Move the ladder instead of reaching sideways. For windows on a second-story stairwell, over a tub or anywhere you cannot set a ladder securely, or for any work two stories up, hire a professional installer with scaffolding or the right equipment.

Choose cordless blinds in homes with young children. Cordless lift and wand tilt systems remove dangling loops and are the child-safe choice, regardless of mounting method.

Troubleshooting Mount Problems

  • Inside mount too tight: You may have deducted from your measurement and the factory deducted again, or the frame narrows somewhere. Check all three widths.
  • Blind hits the crank: Add projection brackets, switch to a low-profile product or convert to outside mount.
  • Brackets will not sit flat on trim: Use shims or spacer blocks so the headrail stays level.
  • Visible gaps on outside mount: Increase overlap on the next order, or add a valance and side panels.
  • Blind not hanging straight: Re-level the brackets; even a slight tilt shows on long blinds.

Cost Considerations

Mounting method rarely changes the product price much, but outside mounts are usually wider and taller, so they cost more per window, often 10 to 25 percent more for the same style. Valances and spacer brackets add small amounts. Professional measuring and installation typically runs $25 to $100 per window, with minimums for small jobs.

Making the Final Call

Go through the checks in order. If depth is short, the frame is out of square, a crank is in the way, or you need darkness, outside mount is the answer. If the window is deep, square and well-trimmed, and a sliver of edge light does not bother you, inside mount gives the cleanest look. Measure with the right rules for your choice, and the inside vs outside mount blinds decision becomes simple.

Frequently Asked Questions

Which blocks more light, inside or outside mount?

Outside mount blocks more light because it overlaps the opening by 1.5 to 3 inches on each side. Inside mounts leave a small gap at each edge for operation.

How deep does a window need to be for inside mount blinds?

It depends on the product. Aluminum mini blinds may need 1 inch, cellular shades about 1 to 1.5 inches, and 2-inch faux wood blinds often need 2.25 to 3 inches for a flush fit.

Should I deduct from my measurements for inside mount?

No. Give the exact narrowest width and the factory subtracts the clearance. Deducting yourself results in a blind that is too narrow.

Can outside mount blinds make a window look bigger?

Yes. Mounting higher and wider than the opening lets the raised blind stack against the wall instead of the glass, so more window shows.

Can I mount blinds outside on a window with no trim?

Yes. Mount the brackets directly into the wall, ideally into framing, and add overlap past the drywall return on each side.