Worn, stained or pilled poker table felt makes even a solid table feel tired, and cards start sticking instead of sliding. The fix is easier than most people expect. If the table has a removable rail, you can strip the old cover, staple or glue on new fabric and have the table back in service in an afternoon, usually for far less than the cost of a new table.
The basic process is the same for almost every table: remove the padded rail, pull the old cloth and staples, prep the board, stretch new fabric from the center outward and reattach the rail. Folding card tables are even simpler, since most have a thin top panel that pops out of the frame. The choices that matter are the type of fabric you buy, how you attach it and how carefully you stretch it.
- Poker Table Felt vs Speed Cloth: Which to Choose
- Tools and Materials
- How to Measure for New Felt
- Step-by-Step: Replacing Felt on a Poker Table
- Safety With Adhesives, Staples and Board Dust
- Recovering a Folding Card Table
- Troubleshooting Common Problems
- Cost to Replace Poker Table Felt
- Caring for New Cloth
- When to Call a Pro
- Frequently Asked Questions
Work in a ventilated space with a clean, flat surface, and take your time with the stretching. Wrinkles and loose spots are almost always the result of rushing.
Poker Table Felt vs Speed Cloth: Which to Choose
“Felt” is used loosely for any table covering, but there are two main families of fabric, and they play differently.
Traditional felt
Wool or wool-blend felt is soft, thick and inexpensive. It gives a classic look and quiet chip stacking. The downside is that it pills over time, absorbs spills and lets cards drag. Felt suits casual tables and budget restorations.
Speed cloth
Speed cloth is a tightly woven polyester or poly blend designed for card play. Cards glide across it for smooth dealing, and it resists pilling, fading and moisture far better than felt. Many speed cloths are water resistant, so a spilled drink beads up long enough to blot. It costs more, but a quality poker table speed cloth lasts years longer than basic felt, which makes it the better value for a table that sees regular use.
Printed and custom cloth
Custom poker felt printed with a logo, a family name or a design is widely available. Most printed covers use a speed cloth base, so they play well, but check the print method. Dye-sublimated prints wear better than surface prints that can crack or fade. Order a little oversized so the design can be centered while stretching.
Tools and Materials
- New felt or speed cloth, at least 6 to 8 inches larger than the playing surface on every side
- Screwdriver or drill with the right bit for the rail screws
- Staple puller, flat screwdriver or needle-nose pliers
- Heavy-duty staple gun with 1/4 to 3/8 inch staples
- Sharp utility knife with fresh blades and scissors
- Spray adhesive rated for fabric to wood (optional, for glued playing surfaces)
- Sandpaper (120 to 150 grit), a vacuum and tack cloth
- Safety glasses, work gloves, and a dust mask or respirator if sanding or cutting board
- Painter’s tape and a marker for alignment marks
How to Measure for New Felt
Measure the playing surface, not the full table. Run a tape across the widest and longest points of the playing board after the rail comes off, or measure inside the rail if it stays on during planning. Then add 6 to 8 inches to each dimension so you have enough fabric to grip and wrap around the board edges.
Oval and racetrack tables need a rectangle that covers the full oval with the same overlap. If the rail cushion is also going to be recovered, buy vinyl or leatherette separately for that job. For a folding card table, measure the removable top panel and add about 4 inches per side.
Step-by-Step: Replacing Felt on a Poker Table
- Remove the rail. Flip the table or look underneath for the screws that hold the padded rail to the playing board. Back them out and lift the rail off. Bag the screws so none go missing.
- Mark the center lines. Before removing the old cloth, mark the center of each side of the board on the underside with tape. You will use these to align the new fabric.
- Strip the old cloth. Pull staples with a staple puller or pliers, wearing safety glasses since staples can snap and fly. If the old cloth was glued, peel it slowly and scrape off loose adhesive lumps.
- Prep the board. Lightly sand high spots and old glue residue, then vacuum and wipe with a tack cloth. Any bump under the cloth will show through, especially with thin speed cloth. Wear a dust mask while sanding, and especially if the board is MDF or particleboard.
- Lay out the fabric. Spread the new cloth face down on a clean floor or work table, then set the board on it face down. Center it, leaving equal overhang on all sides.
- Start in the middle. Pull the fabric snug (not drum-tight) at the center of one long side and place three staples. Go to the opposite side, pull firmly and staple. Repeat for the two short sides.
- Work outward. Continue placing staples every 1 to 2 inches, alternating sides and moving from the center toward the corners. Tension should be even. Pull felt more gently, since it stretches; speed cloth needs firmer, steady pressure.
- Handle the corners or curves. On square corners, fold the excess neatly like a bedsheet and staple flat. On ovals, make small relief cuts in the overhang so it lays flat around the curve without bunching.
- Trim the excess. Cut off extra fabric about an inch past the staples with a sharp blade.
- Check and reinstall. Flip the board, run your hand across the surface to find wrinkles, and fix any area by pulling a few staples and re-stretching. Set the rail back on and drive the screws, snugging them evenly so the rail sits flat.
Stapling vs gluing
Most poker tables have cloth stapled to the underside of the board, which lets you replace it again later. Some tables glue the cloth to the top of the board so it cannot shift. Gluing gives a very flat surface but makes future replacement messier. If you glue, use a light, even coat of spray adhesive on the board only, wait the tack time on the label and lay the fabric down from one end, smoothing as you go.
Safety With Adhesives, Staples and Board Dust
Spray adhesives release solvent vapors that can irritate your lungs and are flammable. Use them outdoors or in a garage with the door open and a fan pushing air out. Keep sprays away from pilot lights, space heaters, cigarettes and any other open flame or spark, and let the vapors clear before bringing the board back inside. Wear gloves and eye protection, and follow the label for respirator use.
Staple guns are a common source of hand injuries. Keep your free hand away from the nose of the gun, never point it at anyone, and unplug or unload powered models before clearing a jam. Wear safety glasses while pulling old staples.
If you need to cut or sand the board itself, wear a dust mask or respirator. MDF and particleboard dust is fine and irritating, and cutting creates a lot of it. Vacuum with a shop vacuum rather than sweeping.
Recovering a Folding Card Table
Folding card tables usually have a top panel held in the frame with a few screws or friction clips. Remove the panel, strip the old vinyl or felt, and wrap new card table felt around it with staples on the back, the same way as a poker board. Use 1/4 inch staples on thin panels so they do not poke through the front. If the panel is cracked or warped, cut a new one from 1/4 inch hardboard or plywood using the old one as a template, wearing a dust mask while you cut.
Thin felt on a card table looks best with a layer of thin foam or batting underneath, which also softens the feel. Lay the foam on the panel, the fabric on top, then staple both together.
Troubleshooting Common Problems
- Wrinkles after reassembly: usually from uneven tension. Remove a few staples in the problem area and re-stretch toward the edge.
- Bubbles on glued cloth: press out from the center with a soft roller while the adhesive is still workable. Old bubbles may need the cloth lifted and re-glued.
- Visible bumps: debris or glue lumps under the cloth. Lift, clean and re-lay.
- Rail will not sit flat: the fabric is bunched at the edge or staples are too close to the rim. Trim excess and move staples inward.
- Cards drag: traditional felt naturally slows cards. Switching to speed cloth fixes it.
Cost to Replace Poker Table Felt
Basic felt for a standard 8-player table often runs in the tens of dollars, while speed cloth and printed custom cloth typically cost more, sometimes reaching into the low hundreds for large or fully custom designs. Adhesive, staples and blades add a modest amount. Upholstery shops and game-table services will do the job for you, usually for a labor charge on top of the fabric, which makes sense for high-value or antique tables.
Caring for New Cloth
Brush the surface with a soft brush or use a handheld vacuum after games. Blot spills right away instead of rubbing. Keep drinks in cup holders, cover the table when not in use and keep it out of direct sunlight, which fades both felt and printed cloth. Speed cloth can usually be spot cleaned with a damp cloth and mild soap, but test an edge first.
When to Call a Pro
Hire an upholsterer if the rail padding is crumbling and needs full recovering, if the table is an heirloom, or if the board is badly warped or water damaged. A pro can also rebuild cup holders and recover the rail vinyl so it matches the new playing surface.
Frequently Asked Questions
How much poker table felt do I need?
Measure the playing surface and add 6 to 8 inches to each side. That extra fabric gives you enough to grip and staple on the underside.
Is speed cloth better than felt?
For regular play, yes. Speed cloth lets cards slide smoothly, resists pilling and handles spills better, while felt is softer and cheaper.
Should I glue or staple poker table cloth?
Stapling to the underside is the most common method and makes future replacement easy. Gluing gives a very flat surface but is harder to undo.
Can I put new felt on a folding card table?
Yes. Remove the top panel, strip the old cover, wrap new felt around it and staple it to the back before reinstalling the panel.
How long does poker table felt last?
Basic felt may wear in a few years with heavy use, while good speed cloth often lasts many years. Covering the table and cleaning spills quickly extends its life.