A full 9 foot garage door looks out of place on a backyard shed, and it wastes wall space you could use for shelves or a window. That is why manufacturers make small garage door sizes such as 5 x 7, 6 x 7 and 8 x 7 feet. These doors fit outbuildings, golf cart garages, mower sheds and motorcycle bays, and they come in both sectional and roll-up styles.
Part of our Garage Doors guide — explore the full guide →
The right size depends on what you plan to drive or roll through the opening, plus the headroom and side room available inside the building. A riding mower usually fits through a 5 or 6 foot door. A standard golf cart needs 6 to 8 feet of width, and a cart with a roof or rear seat often needs a 7 foot tall opening at minimum. Motorcycles and ATVs fall in the same 5 to 8 foot range, depending on handlebar width and whether you want to walk beside the machine.
- Common Small Garage Door Sizes
- Golf Cart Garage Door Size
- Roll-Up vs Sectional Small Doors
- Rough Opening and Headroom Requirements
- How to Measure for a Small Garage Door
- Small Garage Door Openers
- Cost Ranges
- Troubleshooting Common Problems
- When to Call a Licensed Professional
- Frequently Asked Questions
Choosing well means knowing the common sizes, the rough opening each one requires and the headroom a roll-up or sectional door needs to operate.
Common Small Garage Door Sizes
Door sizes are listed width first, then height. A 6 x 7 door is 6 feet wide and 7 feet tall. Most suppliers stock the sizes in the table and can order intermediate widths in 1 foot increments.
| Door Size (W x H) | Typical Use | Notes |
|---|---|---|
| 5 x 7 ft | Push mowers, bikes, small sheds | Tight for riding mowers with decks |
| 6 x 7 ft | Riding mowers, motorcycles, compact carts | Popular shed size |
| 7 x 7 ft | Golf carts, ATVs | Walk-beside room for narrow carts |
| 8 x 7 ft | Golf carts with roofs, small tractors, compact cars | Common single-bay minimum |
| 8 x 8 ft | Lifted carts, utility vehicles | Extra height for racks |
A 6ft garage door is the most popular choice for backyard sheds because it clears a riding mower with a 42 inch deck and still leaves wall space on each side. If you store a utility trailer or a lawn tractor with a wide bagger, step up to 7 or 8 feet.
Golf Cart Garage Door Size
Golf carts vary more than most people expect. A basic two-seat cart is about 4 feet wide and 6 feet tall to the top of the roof. Four-seat and lifted carts can reach 4.5 feet wide and 6.5 to 7 feet tall, especially with oversized tires and a lift kit.
For golf cart garage door dimensions, a good rule of thumb is to add at least 2 feet of width and 6 to 12 inches of height to the cart’s measurements. That means:
- Standard two-seat cart: 6 x 7 ft door works, 7 x 7 ft is more comfortable.
- Four-seat cart: 7 x 7 or 8 x 7 ft.
- Lifted cart with a roof rack: 8 x 8 ft.
Measure the mirrors and roof, not just the body. A cart that clears the opening by an inch will eventually scrape the jamb on a dark evening.
Roll-Up vs Sectional Small Doors
Two door styles dominate the small-door market, and they behave very differently inside the building.
Roll-Up Doors
A roll up garage door is made of corrugated steel curtain that coils onto a drum above the opening. Because it rolls up instead of sliding back along ceiling tracks, it needs very little interior depth. That makes small roll up garage doors a favorite for sheds, storage units and buildings with low ceilings or loft storage.
Roll up door sizes usually start around 3 feet wide and run to 10 feet or more, with common shed models at 5×7, 6×7 and 8×7 feet. A 5×7 roll up door is a practical upgrade over swinging shed doors because it does not need clear ground in front to swing open, and it resists wind better than hinged panels.
Sectional Doors
Sectional doors are made of hinged horizontal panels that ride on tracks along the ceiling. They insulate better and can include windows, which helps if the space doubles as a workshop. The trade-off is that they need more headroom and the full door height in clear ceiling depth behind the opening.
Rough Opening and Headroom Requirements
The rough opening is the framed hole the door fits into. Getting it right is the difference between a smooth install and a costly reframe.
- Width: for most sectional and roll-up doors, the rough opening equals the door width. A 6 foot door goes in a 6 foot opening, with jamb material framing the edges.
- Height: the rough opening equals the door height for sectional doors. Some roll-up models specify a slightly taller opening, so check the maker’s sheet.
- Side room: sectional doors typically need 3.5 to 5 inches on each side for track brackets. Roll-ups need a few inches for guides.
- Headroom: sectional doors usually need 10 to 12 inches above the opening with standard tracks, and less with low-headroom track kits. Roll-up drums often need 14 to 20 inches above the opening, depending on door height.
- Backroom: sectional doors need the door height plus about 18 inches of clear depth behind the opening. Roll-ups need almost none.
Always confirm these numbers against the specific door you buy, because each manufacturer publishes its own installation requirements.
How to Measure for a Small Garage Door
What You Need
- Tape measure
- 4 foot level
- Stepladder
- Pencil and notepad
Steps
- Measure the opening width at the top, middle and bottom. Use the smallest number.
- Measure the opening height on both sides and in the center, from the floor to the header.
- Measure headroom from the top of the opening to the ceiling or lowest obstruction, such as a beam or light fixture.
- Measure side room from each edge of the opening to the nearest wall or obstruction.
- Measure backroom from the opening to the back wall if you are considering a sectional door.
- Check level and plumb. An out-of-level floor can leave gaps under the bottom seal.
Use a stepladder on firm, level ground and keep three points of contact while measuring the header.
Small Garage Door Openers
Many small doors can be automated. Roll-up doors use a jackshaft or side-mount opener that attaches to the drum, while sectional doors use a standard trolley or wall-mount opener. Light-duty openers are fine for most 6 to 8 foot doors, but confirm the opener is rated for the door’s weight and style.
Openers plug into a ceiling outlet. If your shed has no outlet near the door, adding one is a new circuit or branch extension, which is work for a licensed electrician. Outlets in garages and outbuildings generally need GFCI protection. If you ever service an existing opener, turn off the breaker and confirm power is off with a non-contact voltage tester before touching any wiring. Wall buttons and safety sensors run on low-voltage wire, but the opener motor itself runs on line voltage.
Cost Ranges
Small garage door sizes cost less than standard garage doors, but installation can add up if the opening needs reframing. General ranges:
- Basic roll-up shed door: a few hundred dollars for the door alone.
- Insulated sectional small door: several hundred to over a thousand dollars.
- Professional installation: typically a few hundred dollars, more for reframing or an opener.
- Opener and electrical work: a few hundred dollars plus any electrician fee for a new outlet.
Troubleshooting Common Problems
The Door Binds Halfway Up
Check that the guides or tracks are plumb and parallel. On roll-ups, debris in the guides is a frequent cause.
Light Shows Under the Door
The floor is likely uneven. A thicker bottom seal or a threshold seal can close the gap.
Roll-Up Door Will Not Stay Open
Spring tension may be low. Roll-up and sectional springs store a lot of energy, so tension adjustments are best left to a pro.
When to Call a Licensed Professional
Measuring openings and comparing small garage door sizes is easy to do yourself. Installation is a different matter. Garage door springs, especially torsion springs on sectional doors, are under high tension and can cause serious injury if released incorrectly. A trained garage door installer should handle spring work and balancing.
Bring in a licensed contractor if the rough opening needs a new header or if you are cutting a door into a load-bearing wall, since that is structural work that usually requires a permit. Any new outlet or circuit for an opener should be installed by a licensed electrician. Check with your local building department and HOA before changing the front of an outbuilding.
Frequently Asked Questions
What is the smallest garage door size?
Many suppliers offer roll-up doors as narrow as 3 to 4 feet wide, but 5 x 7 feet is the smallest common size sold as a garage-style door for sheds.
What size door do I need for a golf cart?
A 6 x 7 foot door fits most two-seat carts, but 7 x 7 or 8 x 7 feet is more comfortable. Lifted carts with racks often need an 8 x 8 foot door.
Are roll-up doors good for sheds?
Yes. They need very little interior depth, do not swing outward and handle wind well, which makes them a strong fit for sheds and outbuildings.
Can I put an opener on a small roll-up door?
Yes. Side-mount or jackshaft openers attach to the drum. Make sure an outlet is nearby and have a licensed electrician add one if needed.
How much headroom does a small garage door need?
Sectional doors usually need 10 to 12 inches above the opening. Roll-up doors often need 14 to 20 inches for the coiled drum, depending on door height.