Storm windows are one of the cheapest ways to make an old window perform like a new one, but only when they actually close, seal, and hold glass. A cracked pane, a latch that will not catch, or a track packed with grit turns a storm window into a rattling box that lets in drafts and water. The good news is that repairing storm windows is almost always easier and far cheaper than replacing them.
Part of our Windows & Doors guide — explore the full guide →
Most storm window problems come down to five fixes: replacing a broken glass or screen insert, cleaning and lubricating the tracks, swapping worn latches or pins, renewing weatherstripping, and resealing the storm frame to the prime window with the weep holes left open. With a few basic tools and parts from a hardware store or window parts supplier, you can handle all of them in an afternoon.
- Repairing Storm Windows: Know Which Type You Have
- Safety Before You Start
- Tools and Materials
- Step-by-Step: Replace a Glass or Screen Insert
- Clean and Lubricate the Tracks
- Replace Latches, Pins, and Hardware
- Renew Weatherstripping and Reseal the Frame
- Troubleshooting Common Storm Window Problems
- Typical Costs
- When to Call a Glass Shop or Replace the Storm
- Frequently Asked Questions
Below, you will find how to diagnose each problem, the tools you need, step-by-step instructions for aluminum triple-track and wood storm windows, troubleshooting tips, typical costs, and when a glass shop is the better option.
Repairing Storm Windows: Know Which Type You Have
Storm windows come in a few common styles, and the repair approach depends on which one is on your house.
Aluminum triple-track storms
These are the most common on American homes built from the 1950s through the 1990s. A single aluminum frame mounts to the exterior casing and holds three tracks: one for the upper glass sash, one for the lower glass sash, and one for a half screen. Each insert slides up and down and locks with spring-loaded pins or latch tabs. Inserts lift out for cleaning and repair.
Two-track storms
Similar to triple-track, but the screen shares a track with one glass sash. You swap the screen and lower glass seasonally.
Fixed storm windows
Fixed storm windows are a single pane (or panel) that does not open. They are common on picture windows, basement windows, and many historic homes. Repairs usually mean replacing the glass or acrylic and resealing the perimeter.
Wood storm sashes
Traditional wood storms hang from hooks at the top of the window casing and are held tight with turn buttons or hook-and-eye latches at the bottom. They are glazed with putty just like old sash windows and are repaired the same way.
Safety Before You Start
Storm window glass is usually thin, 3/32 or 1/8 inch, and breaks easily into sharp shards. Protect yourself every time you handle an insert.
- Wear cut-resistant gloves and safety glasses whenever you remove, carry, or disassemble a glass insert.
- Remove broken glass from the frame piece by piece, wiggling it free rather than pulling it straight out. Tape large cracked sections first so they come out in one piece.
- Carry inserts vertically, and never stack glass flat where someone can step or lean on it.
- If a storm window is in a door or near the floor, check whether it requires tempered safety glass. Tempered glass cannot be cut to size; order it to exact dimensions.
- On second-story windows, work from inside whenever possible. Most triple-track inserts lift out from the interior side after you open the prime window. Avoid tall ladders while holding glass.
- Homes built before 1978 may have lead paint on wood storms and casings. Test before sanding or scraping, and use wet methods and plastic sheeting if lead is present.
Tools and Materials
- Flat-blade and Phillips screwdrivers, a stiff putty knife, and needle-nose pliers
- Utility knife and a small pry bar
- Glass cutter, straightedge, and running pliers (if you cut glass yourself)
- Replacement glass, acrylic, or polycarbonate cut to size
- Glazing spline or rubber glazing channel (for aluminum sashes)
- Screen fabric, screen spline, and a spline roller
- Replacement latches, pins, or corner keys matched to your frame
- Pile or vinyl weatherstripping
- Dry silicone or PTFE spray lubricant (not oil-based)
- Exterior-grade caulk (siliconized acrylic or polyurethane), and a caulk gun
- Stiff brush, shop vacuum, and mild detergent
Take a broken latch or a piece of the old glazing channel to the store. Storm window hardware varies widely, and matching the profile is the difference between a five-minute fix and a return trip.
Step-by-Step: Replace a Glass or Screen Insert
This covers most aluminum storm sashes, which use a rubber glazing channel wrapped around the glass and held in a frame joined with corner keys or screws.
- Remove the insert. Raise the sash a few inches, pinch the latch tabs or retract the side pins, then tilt the bottom out and lift it from the track.
- Lay it flat on a padded surface. A folded moving blanket on a workbench works well.
- Disassemble one side. Find the screws at one or two corners, usually on the edge of the frame. Remove them and gently pull that side rail off. On crimped frames, drill out the rivets or carefully pry the corner key free.
- Remove the old glass and channel. Slide the glass out with the rubber channel still attached. Strip the channel off and clean it, or buy new if it is brittle or cracked.
- Measure for the new glass. Measure the old pane, or measure the inside of the frame channel and subtract about 1/8 inch in each direction. Order glass cut to size, or cut it yourself with a glass cutter and straightedge.
- Wrap the new glass. Starting at one corner, press the glazing channel around all edges, notching it at the corners so it lies flat.
- Reassemble. Slide the wrapped glass into the three attached rails, press the fourth rail on, and reinstall the screws or corner keys. The frame should be square; check by measuring diagonals.
- Reinstall the insert in its track and test that it slides and locks.
For screens, the process is simpler: pull out the old spline, lay new fabric over the frame, and roll new spline into the groove with a spline roller, working from one corner around the frame while keeping the fabric taut. Trim excess with a utility knife.
Fixed storm windows and wood storms
On fixed storm windows, remove the interior stops or retaining clips, take out the old pane, clean the rabbet, and set the new glass on a thin bead of glazing sealant before replacing the stops. On wood storms, remove old putty with a heat-free method (a putty knife and patience, or an infrared softener used carefully in lead-safe conditions), pull the glazier’s points, set the new glass on a bed of compound, push in new points every 6 to 8 inches, and tool fresh glazing compound at a 45-degree angle. Let it skin over for about a week before painting.
Clean and Lubricate the Tracks
Sticking sashes are often just dirty tracks. Decades of dust, pollen, paint drips, and dead insects collect in the channels and grind against the sash.
- Remove all inserts from the frame.
- Vacuum the tracks with a crevice tool, then scrub with a stiff brush and warm water mixed with dish soap.
- Scrape paint drips or hardened caulk carefully with a putty knife. Do not gouge the aluminum.
- Rinse and dry completely.
- Spray a light coat of dry silicone or PTFE lubricant along each track. Skip oils and greases; they attract grit and make things worse within a season.
- Reinstall the inserts and slide each one through its full range of travel several times.
Replace Latches, Pins, and Hardware
Triple-track storms use small spring-loaded latches at the sides or a pin-and-hole system to hold each sash at different heights. When a latch breaks, the sash slides down on its own or falls out entirely.
- Latch tabs: Most are held by a rivet or small screw. Drill out the rivet, remove the old latch, and attach the new one with a pop rivet or a stainless screw.
- Spring pins: Pull the old pin assembly from its housing with needle-nose pliers and press a replacement in until it seats.
- Corner keys: Cracked corner keys let a sash rack out of square. Replace them while the sash is disassembled for glass work.
The same approach applies to storm door window latch replacement. Storm doors with sliding glass and screen panels use a similar latch-and-track system; identify the brand and model (usually on a sticker on the hinge side) to order the right retainer clips or latches.
Renew Weatherstripping and Reseal the Frame
A storm window only insulates well when the air space between it and the prime window is reasonably tight. Two places leak: the sash-to-frame seal, and the frame-to-house seal.
Sash weatherstripping
Many aluminum sashes have pile weatherstrip in a small groove along the edges. If it is matted or missing, pull out the old strip and slide in new pile of the same backing width. Wood storms can take a self-adhesive foam or vinyl bulb strip on the stop where the storm meets the casing.
Sealing the frame to the prime window
Run a bead of exterior caulk where the storm frame’s top and sides meet the house casing. Do not caulk the bottom rail. Aluminum storm frames have small weep holes or slots along the bottom edge so condensation and rain can drain out. Seal them and water will pool on the prime window sill, rotting wood and peeling paint. If your frame has no weep holes, drill two 1/4-inch holes near each end of the bottom rail.
Troubleshooting Common Storm Window Problems
Condensation between storm and prime window
Moist indoor air is leaking out past the prime window and condensing on the cold storm glass. Tighten the prime window with weatherstripping, and make sure the storm’s weep holes are open. The storm should be slightly less airtight than the interior window, not more.
Sash will not stay up
Latches or pins are worn, or the track is bent. Replace the hardware first; if the track itself is bent, straighten it gently with a wood block and a mallet.
Rattling in the wind
Worn pile weatherstrip or loose corner joints. Replace the pile and tighten the corner screws.
Frame pulling away from the house
Mounting screws may have stripped out of soft or rotted casing. Probe the wood with an awl. If it is solid, move the screws to fresh spots; if it is soft, repair the rot with epoxy filler or replace the casing before remounting.
Typical Costs
- Cut-to-size glass for one storm insert: commonly $15 to $50 depending on size.
- Screen repair kit: roughly $10 to $25 for fabric, spline, and a roller.
- Latches, pins, or corner keys: usually a few dollars each.
- Weatherstripping and caulk: about $15 to $30 per window.
- Professional reglazing or insert repair at a glass shop: often $50 to $150 per insert.
- New custom aluminum storm window installed: typically a few hundred dollars each, which is why repair usually wins.
When to Call a Glass Shop or Replace the Storm
Repairing storm windows is well within DIY range for most homeowners, but a pro or replacement makes sense when:
- The storm is in a door or low location and needs tempered glass you cannot cut yourself.
- The frame is badly bent, corroded, or the tracks are cracked through.
- The windows are on an upper floor and inserts cannot be removed from inside.
- You have historic wood storms with lead paint and need lead-safe paint removal.
- Replacement hardware for your model is no longer available and multiple sashes are failing.
Many local glass shops will reglaze an aluminum insert while you wait if you bring it in, which is a fast, low-cost middle ground.
Frequently Asked Questions
Are storm windows worth repairing?
Usually, yes. A working storm window can noticeably reduce drafts and heat loss through a single-pane prime window, and parts are inexpensive. Repair costs are typically a fraction of new storms.
Can I use acrylic instead of glass in a storm window?
Yes. Acrylic or polycarbonate is lighter and resists breakage, which is helpful for kids’ rooms and basement storms. It scratches more easily and can yellow over time, so glass remains the clearer long-term option.
How do I fix fixed storm windows that fog up?
Fogging usually means indoor moisture is leaking past the prime window. Weatherstrip the interior window and confirm the storm has open weep holes along the bottom so moisture can escape.
How do I handle storm door window latch replacement?
Find the manufacturer label on the door frame, order matching latches or retainer clips, and swap them with a screwdriver or by drilling out the old rivet. Bring the old part to the store if you cannot identify the brand.
Should storm windows be caulked all the way around?
No. Caulk the top and sides, but leave the bottom rail and its weep holes open so water and condensation can drain out.