A 6 inch PVC pipe is not actually 6 inches across on the outside. Its nominal size refers to a standard, and the true outside diameter is 6.625 inches for both Schedule 40 and Schedule 80. What changes between schedules is the wall thickness, which changes the inside diameter, weight and pressure rating. Get that straight and most fitting, coupling and trench-sizing questions answer themselves.
Schedule 40 6-inch pipe has a minimum wall of 0.280 inch and an inside diameter of about 6.065 inches. Schedule 80 has a thicker 0.432 inch wall and an inside diameter of about 5.76 inches. Both come in 10 and 20 foot lengths, with plain or belled ends, and both fit standard 6-inch Schedule 40 and 80 fittings because the outside diameter matches.
One common mix-up: 6-inch sewer and drain pipe sold as SDR 35 or thin-wall sewer pipe uses a different outside diameter and does not fit Schedule 40 fittings without adapters. Check the print line on the pipe before buying fittings.
6 Inch PVC Pipe Dimensions and Specs
These figures follow the standard dimensions for Schedule 40 and 80 PVC pressure pipe. Wall values are minimums; actual inside diameter can vary slightly by maker.
| Spec | Schedule 40 | Schedule 80 |
|---|---|---|
| Outside diameter | 6.625 in | 6.625 in |
| Minimum wall | 0.280 in | 0.432 in |
| Inside diameter (approx.) | 6.065 in | 5.76 in |
| Weight per foot (approx.) | 3.5 to 3.6 lb | 5.5 to 5.6 lb |
| Pressure rating at 73°F (typical) | 180 psi | 280 psi |
| Common lengths | 10 ft and 20 ft | 10 ft and 20 ft |
| Typical color | White | Gray |
| Price range, 10 ft | About $40 to $100 | About $90 to $200 |
| Price range, 20 ft | About $80 to $200 | About $180 to $400 |
Pressure ratings drop as temperature rises, and PVC is not meant for hot water. Prices swing widely by region, supplier and resin costs, so treat the ranges as a rough budget, not a quote. A 20-foot length of Schedule 40 weighs about 70 pounds, so plan for two people when carrying it.
Schedule 40 vs Schedule 80: Which Do You Need?
For most homeowner jobs, Schedule 40 is the right choice. It handles drain, waste and vent lines, yard drainage, downspout runs and many irrigation mains. It is lighter, cheaper and easier to cut.
Schedule 80 makes sense when you need higher pressure capacity, more impact resistance or extra wall for threading. It shows up in commercial plumbing, industrial chemical lines, exposed runs that might get hit and some pool and pump systems. The thicker wall reduces flow area slightly, about 10 percent less cross-section than Schedule 40.
Foam core vs solid wall
Some 6-inch Schedule 40 drain pipe is foam core (cellular core), which is lighter and meant for non-pressure drain, waste and vent use only. Solid-wall pipe is required for pressure lines. The print line on the pipe tells you which you have.
Pipe vs sewer pipe vs conduit
Electrical conduit in 6-inch size shares the 6.625 inch outside diameter but is made to a different standard and is not rated for pressure water. Thin-wall sewer pipe uses its own diameter. Buy pipe marked for your exact use.
Common Uses for 6-Inch PVC
- Building sewer lines: Six-inch pipe is common for larger homes, multi-unit buildings and longer runs to the street, where local code or the utility may require it.
- Yard and site drainage: Collector lines for French drains, catch basins and multiple downspouts.
- Small driveway culverts: Short crossings with light flow. Larger ditches usually need bigger corrugated or concrete culvert pipe.
- Sump and storm discharge: Carrying water well away from the foundation.
- Irrigation and agricultural mains: Large-volume water supply on farms and big properties.
- DIY projects: Planters, storage tubes, tool holders and fence post sleeves.
For culverts, size the pipe to the drainage area, not the look of the ditch. Undersized culverts back up and wash out driveways. Your local road or permit office can tell you the minimum size for a driveway crossing.
Tools and Materials
- PVC pipe cutter rated for 6-inch pipe, or a fine-tooth hand saw or reciprocating saw with a miter guide
- Deburring tool or file and sandpaper
- Tape measure and marker
- PVC primer and solvent cement rated for large-diameter pipe
- Wide applicator (dauber) sized for 6-inch pipe
- Gloves, eye protection and good ventilation
- Level, string line and shovel for trench work
Large-diameter joints need heavy-bodied cement and a fast, confident technique. Small daubers leave dry spots that cause leaks.
How to Cut and Join 6 Inch PVC Pipe
- Measure and mark. Include the socket depth of each fitting in your measurement.
- Cut square. Use a large pipe cutter or a saw in a miter box. A crooked cut leaves a gap at the socket bottom.
- Deburr and chamfer. Remove burrs inside and out and bevel the outer edge slightly so cement is not scraped off.
- Dry fit. The pipe should enter the fitting about a third to two-thirds of the socket depth by hand.
- Prime. Apply primer to the outside of the pipe and inside of the fitting.
- Cement. Apply an even coat to both surfaces while the primer is still wet.
- Assemble. Push the pipe fully in with a quarter turn and hold it for 30 seconds or more, since large pipe tends to push back out.
- Cure. Follow the cement label for set and cure times before burying or pressure testing. Cold weather extends cure time.
Work with primer and cement in a ventilated area, away from pilot lights and flames, and wear gloves and eye protection. These products give off flammable vapors.
Choosing Fittings for 6-Inch Pipe
Because Schedule 40 and Schedule 80 share the 6.625 inch outside diameter, both slide into standard 6-inch socket fittings. The fitting itself has its own rating, though, so a Schedule 40 fitting on Schedule 80 pipe limits the joint to the lower rating. Match fitting schedule to the pipe when pressure matters.
For drain lines, use drain, waste and vent pattern fittings with long sweeps rather than sharp pressure elbows. Long-radius bends and wye fittings keep solids moving and make cleaning easier. Add a cleanout where a drain line changes direction or leaves the house, so a drain snake can reach the full run.
When connecting 6-inch Schedule 40 to thin-wall sewer pipe, clay or cast iron, use a transition coupling made for those two specific materials. These rubber couplings with stainless bands are sized by the outside diameter of each pipe, so measure both before buying.
Belled-end pipe saves a coupling at every joint, which adds up on long runs. Plain-end pipe gives more flexibility when you need many short cut pieces. On a 100-foot run with 20-foot lengths, belled pipe removes four couplings and four glued joints.
Burying 6-Inch PVC
Call 811 before you dig so buried utilities are marked. Dig a trench with a firm, even bottom. For drain lines, keep a steady slope, commonly at least 1/8 inch per foot for 6-inch pipe, unless your local code sets a different value. Bed the pipe in sand or fine gravel, avoid rocks against the pipe, and backfill in layers. Use a tracer wire or warning tape if you may need to find the line later.
Troubleshooting
Fittings will not fit: You likely have thin-wall sewer pipe or a different standard. Compare the outside diameter and print line, and use a proper adapter coupling.
Leaking joints: Usually from a dry spot in the cement, a cut that is not square or pipe pushed out before setting. Cut out the joint and redo it with a new coupling.
Sagging lines: Underground pipe needs uniform bedding. Above ground, add hangers or supports at the spacing the maker recommends.
Cracking in sunlight: Standard PVC weakens with long UV exposure. Paint exposed pipe with a water-based exterior paint or shade it.
When to Call a Licensed Plumber
Building sewer lines, connections to the city main or septic system and any pressure water line usually need a permit and inspection. Hire a licensed plumber for those, and for any job where you are unsure of the code requirements in your area. Shut off water and relieve pressure before cutting into any existing supply line. For culverts, check with your local road department, since they often control size and placement.
Frequently Asked Questions
What is the outside diameter of 6 inch PVC pipe?
Schedule 40 and Schedule 80 6-inch PVC both have an outside diameter of 6.625 inches.
What is the inside diameter of 6 inch Schedule 40 pipe?
About 6.065 inches, based on a 0.280 inch minimum wall.
How much does a 20 ft length of 6 inch PVC cost?
Schedule 40 typically runs about $80 to $200 for 20 feet, and Schedule 80 costs more. Prices vary a lot by region and supplier.
Is Schedule 80 stronger than Schedule 40?
Yes. Its thicker wall gives a higher pressure rating and more impact resistance, at the cost of weight, price and a slightly smaller inside diameter.
Can 6 inch Schedule 40 be used for a sewer line?
Often yes, but local code decides. Some areas allow thin-wall sewer pipe instead. Check with your building department before buying.
How much does 6 inch PVC pipe weigh?
Solid-wall Schedule 40 weighs about 3.5 to 3.6 pounds per foot, and Schedule 80 about 5.5 to 5.6 pounds per foot.