Home Improvement

Accordion Screen Door: Pleated Screens for Wide and French Doors

Accordion Screen Door: Pleated Screens for Wide and French Doors

Outswing French doors and extra-wide openings are notoriously hard to screen. A hinged screen door would collide with the doors, and a standard sliding screen needs a track the doorway does not have. An accordion screen door solves both problems. The mesh is folded into pleats like a paper fan, rides on a slim top and bottom track, and stacks into a compact housing at the side when you do not need it. It has no spring, so it stays wherever you leave it.

Because it mounts inside the door frame, a pleated screen leaves room for doors that open outward. It also handles openings much wider than most retractable screens can manage, often 6 to 12 feet or more when you use a double unit that meets in the middle. That makes it a strong option for patio doors, multi-panel folding doors and garage entries as well as French doors.

Success depends on accurate measuring, a level track, and choosing the right configuration: single-sided, double-sided, or meeting in the center.

How an Accordion Screen Door Works

An accordion screen door is a pleated mesh panel held between two rigid end posts. One post mounts to the side jamb inside a housing; the other is a handle bar that you pull across the opening. As you slide it, the pleats unfold and the mesh spreads evenly. Small internal cords run through the pleats to keep them evenly spaced and taut, so the screen does not sag even across wide spans.

The bottom track is very low, usually around 1/4 to 1/2 inch high, which keeps the threshold easy to step over and roll a cart across. Some models use a near-flat track for accessibility. The top track carries most of the alignment and keeps the screen from swinging in wind.

Why No Spring Matters

Roller retractable screens use a spring to pull the mesh back into a cassette. That spring can snap the screen closed if you let go, and wide springs lose tension over time. A pleated screen has no spring, so it stays put at any position, which is helpful for kids, pets and anyone carrying things through the door.

Screens for French Doors That Open Out

If you have been searching for a screen for French doors that open out, this is usually the best fit. Outswing doors swing onto the patio or deck, so the screen must sit inside the frame, on the interior side of the doors. A pleated screen mounted on the inside face of the jamb lets the doors swing outward freely while the mesh closes the opening from inside.

For inswing French doors, the screen mounts on the exterior side of the frame instead, so the doors can still open into the room. Check the depth of your jamb: you need enough flat surface for the track and housing, usually around 1 1/4 to 2 inches. If your jamb is shallow, a build-out strip of trim can add the depth.

Single, Double and Center-Meeting Configurations

  • Single: One housing on one side; the screen pulls all the way across and latches on the opposite jamb. Good for openings up to roughly 6 or 7 feet.
  • Double, center meeting: Two housings, one on each side; the screens meet in the middle. Ideal for French doors because each half matches a door leaf.
  • Double, side meeting: Two screens joined so they move as one, used for very wide openings.

Center-meeting units are the most popular for French doors and wide patio openings because each half is shorter to pull and the screen stacks on both sides.

Measuring and Sizing

Pleated screens are often sold in size ranges and trimmed to fit, or made to order. Measure carefully:

  1. Measure the width of the opening inside the jamb at the top, middle and bottom. Note the smallest measurement.
  2. Measure the height on both sides and in the center. Note the smallest number.
  3. Check the floor or threshold for level with a long level. Note any slope; a low corner can leave a gap under the screen.
  4. Check the jamb for plumb on each side. An out-of-plumb jamb makes the screen bind or gap.
  5. Measure the jamb depth where the housing will mount and note any obstacles such as door hardware or weatherstrip.

Order a unit whose range covers your smallest dimension. Many pleated screen door kits have height-adjustable tracks or cut-down instructions.

Tools and Materials

  • Pleated screen door kit sized to your opening
  • Drill/driver with bits suited to your frame
  • Hacksaw or fine-tooth saw for trimming aluminum tracks
  • Level (4 feet or longer) and tape measure
  • Pencil, square and file to deburr cut edges
  • Shims and exterior caulk
  • Safety glasses
Looking to buy Accordion Screen Door? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Step-by-Step Installation

  1. Prep the opening. Clean the jamb and threshold, and remove anything that interferes with the mounting surface.
  2. Trim the tracks. Cut the top and bottom tracks to the opening width, following the kit’s deductions. Deburr the cut ends.
  3. Mount the top track. Fasten it to the head jamb, checking level along its length.
  4. Set the housing. Install the side housing on the jamb, plumb, and fasten it so it engages the top track.
  5. Install the bottom track. Align it directly beneath the top track, using a level to transfer the line. Shim or use the kit’s leveling strip if the threshold slopes. Fasten or adhere it as instructed.
  6. Insert the screen. Fit the pleated mesh into the tracks and connect it to the housing.
  7. Install the strike or magnet. Mount the receiving post or magnetic strike on the opposite jamb, or the center connection for double units.
  8. Adjust. Tension the internal cords if the kit allows, then test the screen several times across the full width.
  9. Seal. Caulk gaps along the housing and jamb to keep insects out.

Take your time on the bottom track. Most operating problems trace back to a track that is not directly under the top track.

Pleated Screens vs Roller Retractables

Roller retractable screens roll into a cassette and look very clean when hidden, but they rely on springs, can be awkward on very wide spans, and usually need a brake to avoid snapping shut. A pleated screen door has no spring, stays at any position, and handles wider openings with less sag. Pleated mesh is a bit more visible when stacked, and the pleats can collect dust, but many owners find the tradeoff worthwhile for French and folding doors.

Troubleshooting

The Screen Is Hard to Pull

Clean the bottom track of debris and pet hair, then use a dry silicone spray on the tracks. Avoid oily lubricants, which attract dirt. If it binds in one spot, the tracks may be out of alignment.

Gaps at the Top or Bottom

A sloping threshold is usually the cause. Add the kit’s leveling strip or shim the bottom track. Check that the top track has not sagged.

The Mesh Sags or Pleats Bunch

Internal cords may need tension adjustment. Follow the kit’s instructions; overtightening makes the screen hard to open.

Wind Pulls the Screen Out of the Track

Close it when wind picks up, or choose a model with deeper tracks or a wind-lock feature for exposed doors.

Cost Ranges and Care

Pleated screens cost more than basic hinged screen doors but are often comparable to good roller retractables. Off-the-shelf single units generally run from around one hundred to a few hundred dollars, while double units for French doors and custom wide openings cost more. Professional installation adds labor, often a modest charge for standard openings and more for custom sizes.

To keep the screen working well, vacuum the pleats and track a few times a season, wash the mesh gently with mild soap and water, and leave the screen stacked when not in use during winter. A well-maintained unit can last many years.

When to Call a Pro

Call a professional installer or screen company if your opening is very wide, out of square or plumb by more than about 1/4 inch, has stone or masonry jambs, or requires custom build-outs. A pro can also measure accurately for made-to-order units, which reduces the chance of an expensive misfit.

Frequently Asked Questions

Can an accordion screen door work with outswing French doors?

Yes. It mounts inside the frame on the interior side, so the doors can swing outward while the screen closes the opening from inside.

How wide can a pleated screen door be?

Single units often cover around 6 to 7 feet, and double center-meeting units can span much wider openings, sometimes 12 feet or more.

Does an accordion screen have a spring?

No. Pleated screens slide along tracks and stay at any position, which makes them safer and easier to control than spring-loaded roller screens.

Is the bottom track a trip hazard?

Bottom tracks are usually very low, around 1/4 to 1/2 inch, and some models have near-flat tracks for easy access.

How do I clean a pleated screen?

Vacuum the pleats with a brush attachment, then wipe with mild soapy water and let it dry before stacking it back into the housing.