Home Improvement

Deck Stairs With Landing: Layout, Footings and Code Basics

Deck Stairs With Landing: Layout, Footings and Code Basics

A tall deck with one long, straight stair run is a common inspection failure, and it also eats a huge strip of your yard. Building deck stairs with landing platforms breaks a long climb into two shorter flights, gives you a place to turn the stairs 90 or 180 degrees, and keeps total rise per flight inside the limits most building departments enforce. The landing itself is a small deck: it needs its own footings, its own beams and joists, and solid connections to the stringers on both sides.

Most homeowners need a landing when the deck surface sits roughly 12 feet or more above grade, when the stairs must change direction to fit the lot, or when a door or walkway sits right where a straight run would land. The steps are simple once the math is right: measure total rise, decide where the landing goes, set footings below the frost line, frame the platform level, then cut two sets of stringers that match exactly.

All the dimensions here are code-typical values from model residential codes. Local rules vary by city and county, so treat every number here as a starting point and confirm it with your building department before you buy lumber.

When Deck Stairs With Landing Platforms Are Required

Model residential codes generally cap the vertical rise of a single stair flight at about 12 feet (often written as 147 or 151 inches, depending on the edition your area adopted). Once your total rise passes that number, a landing becomes mandatory. Many builders add one well before that point because a 9 or 10 foot straight run looks steep, feels steep, and often lands in the middle of a lawn or garden.

Other common triggers for outdoor deck stairs with landing layouts include:

  • A turn in direction. L-shaped and U-shaped (switchback) stairs need a landing at each turn.
  • A door at the top. A swinging door generally needs a landing on each side, and the deck itself usually serves as the top landing.
  • Limited yard depth. A long straight run might need 14 to 18 feet of horizontal space. A switchback can cut that in half.
  • Property lines and setbacks. Turning the stairs can keep the bottom step inside your buildable area.

The bottom of every flight also needs a landing, which on most decks is a level pad of concrete, pavers or compacted gravel at least as wide as the stairs and roughly 36 inches deep in the direction of travel.

Code-Typical Dimensions to Confirm Locally

Inspectors look at the same handful of numbers on nearly every set of exterior stairs. These are the values found in many model codes; your local version may differ, so verify each one.

  • Riser height: 7 3/4 inches maximum is common, with no more than 3/8 inch variation between the tallest and shortest riser in a flight.
  • Tread depth: 10 inches minimum is common, measured nosing to nosing, again with no more than 3/8 inch variation.
  • Stair width: 36 inches minimum clear width is typical.
  • Landing size: at least as wide as the stairs it serves and at least 36 inches deep in the direction of travel.
  • Handrails: required on at least one side once a flight has four or more risers, usually set 34 to 38 inches above the tread nosing, with a graspable profile and continuous along the flight.
  • Guards: required on open sides of stairs and landings that sit more than about 30 inches above the grade below, with openings small enough that a 4 inch sphere cannot pass through.
  • Open risers: if risers are open, the gap is typically limited so a 4 inch sphere cannot pass.

Keep riser heights uniform. A single step that is half an inch taller than its neighbors is one of the most common trip hazards on any staircase, because your foot memorizes the rhythm of the first two or three steps.

Tools and Materials

  • Framing square with stair gauges, 4 foot level, string line and line level or a laser level
  • Circular saw, jigsaw or handsaw for finishing stringer cuts, and a drill/driver
  • A framing nailer speeds up joist and blocking work on the landing platform; use nails rated for treated lumber and for the hangers you install
  • Post hole digger or auger, concrete mix, tube forms and post bases
  • Ground-contact pressure-treated lumber for posts, beams, joists and stringers (2×12 for stringers is standard)
  • Joist hangers, post caps, stringer brackets and structural screws rated for treated wood
  • Decking for treads and landing surface, plus railing and baluster material
  • Safety glasses, gloves, hearing protection and a dust mask for cutting treated lumber

Step-by-Step: Planning and Building the Landing

1. Measure total rise accurately

Run a level from the top of the deck surface out past where the stairs will end, then measure straight down to finished grade. On sloped yards, measure at the actual spot where the bottom step will land, since a few inches of slope changes the riser count. Divide the total rise by 7.5 and round up to get a starting riser count, then divide total rise by that count to get the exact riser height.

2. Decide where the landing breaks the run

Split the risers between two flights. For a 10 foot rise (120 inches) and 16 risers at 7.5 inches each, you might put 8 risers above the landing and 8 below. The landing surface then sits 60 inches below the deck surface. Note that the landing surface counts as a riser step, so lay out the numbers on paper and check that each flight lands on a whole riser.

3. Lay out the footprint and call 811

Mark the landing corners with stakes and string, square it with the 3-4-5 method, and mark post locations. Before digging, call 811 at least a few business days ahead so utility lines get marked. Gas, electric and fiber lines often run right through side yards where stairs go.

4. Dig and pour footings below the frost line

Footings for the landing must go below your local frost depth, which can range from a few inches in the Deep South to 48 inches or more in northern states. Shallow footings heave in winter and pull the landing out of level, which twists the stringers. Size footings to the soil and load per your local requirements; 12 inch diameter tube forms over a flared base are common for small landings. Set post bases in the wet concrete or anchor them after cure.

5. Frame the landing platform

Set posts, mark the landing height with a laser or string, and attach beams with post caps or notched connections approved locally. Hang joists at 12 or 16 inches on center depending on the decking you plan to use. Diagonal bracing between posts and beams helps resist sway, especially on platforms more than a few feet tall. The finished landing should be dead level side to side and within a slight slope for drainage.

6. Cut and test-fit stringers

Lay out the upper and lower stringers with stair gauges set to your exact rise and run. Remember to subtract one tread thickness from the bottom cut so the first step matches the others. Cut one stringer, test-fit it in place, check every riser with a level and tape, then use it as a pattern for the rest. Space stringers no more than about 16 inches apart for wood treads; composite treads often require 12 inches or less, so follow the tread maker’s span chart.

7. Connect stringers to deck and landing

Attach the upper flight to the deck rim with stringer hangers or a ledger board, and attach the lower flight’s top end to the landing rim the same way. The bottom of the lower flight rests on a concrete pad or treated kicker plate anchored to a footing so it cannot slide. Never rest stringers directly on soil.

8. Install treads, handrails and guards

Fasten treads with structural screws, leaving small gaps for drainage. Install guard posts with through-bolts or approved post connectors into the framing, not just the decking. Continuous handrails should be graspable and secure enough to stop a fall, so check them by leaning hard on every section.

Connecting Two Stringer Runs Cleanly

Most problems with exterior stairs with landing layouts show up at the transitions. The upper flight’s bottom riser must land exactly one riser height above the landing surface, and the lower flight’s top riser must step down exactly one riser height. If your landing ends up even an inch too high or low, one of those transitions will be off, so set landing height from your calculated numbers rather than from what looks right.

For a 90 degree L turn, the landing is usually square, matching the stair width in both directions. For a 180 degree switchback, the landing must be at least twice the stair width plus any gap between flights, and often 36 to 48 inches deep. Plan guard and handrail posts so they do not crowd the walking path at the turn.

Need help with your decking project? Get a free quote by phone.
📞 Call (888) 268-1507
Free, no-obligation quote · Connect with a local pro

Slip and Trip Safety

Outside stairs with landing platforms see rain, leaves, ice and algae, so plan for traction from day one. Choose textured decking or add slip-resistant strips to tread nosings. Keep treads gapped so water drains instead of pooling. Light the stairs with low-voltage step or post lights so every tread edge is visible at night, and keep landings clear of planters or furniture that narrow the path. Sweep off wet leaves, and in winter use a plastic shovel and a deck-safe ice melt instead of metal tools that gouge the surface.

Troubleshooting Common Problems

  • Uneven riser at the top or bottom: usually from forgetting tread thickness or measuring rise to sloped grade. Adjust the bottom pad height rather than cutting a single odd step.
  • Bouncy landing: add blocking between joists, check beam size, and add diagonal bracing to posts.
  • Stringers twisting or cracking: often from poor support at the landing connection or stringer spacing that is too wide. Add a center stringer and proper hangers.
  • Landing sinking on one corner: a footing that was too shallow or set on loose fill. This needs a footing repair, not shims.
  • Wobbly handrail: posts fastened only through decking. Rebolt into framing with blocking behind.

General Cost Ranges

DIY materials for a single landing and two short flights in pressure-treated lumber commonly run from several hundred dollars to roughly $1,500, depending on height, footing count and railing style. Composite treads and aluminum or glass railings can double that figure. Hiring a deck contractor for outdoor steps with landing construction often runs a few thousand dollars for a basic build and more for tall, multi-turn stairs, plus permit fees that vary widely by town.

When to Call a Professional

Pull a permit before you start. Most jurisdictions require one for deck stairs, and an inspector will usually want to see the footing holes before you pour. Hire a licensed deck builder or structural engineer when the landing is more than a few feet tall, when you are attaching to an older deck with unknown framing, when soil is soft or sloped, or when you live in a high wind or heavy snow region. A pro is also worth the cost for tall switchback stairs, where small layout errors add up fast. If any lighting needs new line-voltage wiring, that part belongs to a licensed electrician.

Frequently Asked Questions

How tall can deck stairs be before a landing is required?

Many model codes limit a single flight to roughly 12 feet of vertical rise. Above that, a landing is required. Check your local code, since the exact figure depends on the edition adopted in your area.

How big should a deck stair landing be?

Plan for a landing at least as wide as the stairs and at least 36 inches deep in the direction of travel. Switchback landings must be wider to fit both flights side by side.

Does a stair landing need its own footings?

Yes. A landing is a small structure and needs posts on footings that extend below the local frost line, or it will heave and shift over time.

Do exterior steps with landing platforms need guards?

Guards are typically required on open sides of stairs and landings more than about 30 inches above the grade below. Handrails are usually required on flights with four or more risers.

Can I build deck stairs with a landing myself?

Many confident DIYers can, provided they pull a permit, call 811, set proper footings and follow the inspector’s requirements. Tall or multi-turn stairs are often better left to a licensed builder.

Get Free Deck Building Quotes from Local Pros