A 1/8-inch gap around a standard entry door leaks about as much air as a 6-inch-square hole punched straight through the wall. That is why door insulation pays back faster than almost any other weatherization project — the Department of Energy pegs air sealing savings at 10 to 20 percent of heating and cooling costs, and doors are the worst offenders per square foot. The trick is thinking of the door as a system with four leak paths: the slab itself, the perimeter seal, the bottom gap, and the threshold. Fix all four, in the right order, and the draft disappears.
Part of our Windows & Doors guide — explore the full guide →
Find the Leaks Before You Buy Anything
Diagnose first, shop second. On a windy day, hold a lit incense stick or a strip of tissue paper around the door perimeter and watch for movement. At night, have someone shine a flashlight around the closed door from outside — any light you see inside is an air path. The classic dollar-bill test works on the seals themselves: close the door on a bill at several points around the perimeter. If it slides out with no resistance, the weatherstripping at that spot is not sealing.
Map what you find. Gaps at the sides and top point to worn perimeter seals or a door that needs hinge adjustment. A glow under the door means sweep or threshold. Cold radiating through the center of a closed, well-sealed door means the slab itself is the problem.
The Door Slab: R-Value Starts at the Core
An old solid-wood door insulates to about R-2 or R-3. A hollow-core door — never appropriate for an exterior opening, but common on garage-to-house doors in older homes — is closer to R-1. Modern insulated steel and fiberglass doors carry polyurethane foam cores rated R-5 to R-13, which is why replacing a 1960s wood slab is sometimes the honest answer when the door is also warped or cracked.
If replacement is not in the budget, you can still improve the slab. Add a storm door ($150 to $500) to create a dead-air buffer that adds roughly R-1 to R-2 and shields the weatherstripping from wind. For doors with single-pane glass lites, an interior acrylic insert or even seasonal window film cuts the loss through the glass, which is always the weakest part of the slab.
Seal the Perimeter: Sides and Top
The jamb seal does most of the work, and it wears out every 5 to 10 years. Modern prehung doors use kerf-mounted bulb weatherstripping that pulls out of a slot and replaces in minutes for about $15 a kit. Older doors take nail-on or adhesive seals. Choosing among V-strip, foam, silicone bulb, and felt is its own topic — our weatherstripping for doors guide covers each product and how to install it correctly. The strategic point here: replace the whole perimeter at once, not just the section that failed, because compression set ages all of it at the same rate.
Before installing new seals, fix the geometry. A door that has sagged on its hinges will crush the seal at one corner and miss it entirely at the opposite one. Tighten hinge screws, or swap one screw per hinge for a 3-inch screw driven into the stud, and check that the gap between slab and jamb is an even 1/8 inch all around. Adjustment is free; no seal compensates for a crooked door.
The Bottom Gap: Sweeps and Shoes
The gap under the door leaks the most air because wind pressure and stack effect both concentrate there. A door sweep — an aluminum strip with a vinyl or brush fin screwed to the door’s interior face — closes gaps up to about 1 inch for $10 to $25. Door shoes wrap the bottom edge of the slab and seal against the threshold with a vinyl bulb; they are more durable but require pulling the door off its hinges to install. For rental units or quick fixes, an under-door draft stopper (the twin-tube foam kind) works without tools, though it drags on carpet and falls off eventually.
Thresholds and Sills
Most exterior thresholds since the 1980s are adjustable: four or five screws along the top raise or lower a strip to meet the door’s bottom seal. Turn them counterclockwise a half turn at a time until the dollar-bill test shows even resistance across the width. If the threshold’s vinyl insert is cracked or flattened, replacement inserts cost $8 to $15 at any big-box store — measure the width and profile before you go. Rotted wood thresholds under old doors should be replaced outright, and while it is open, add a bead of sealant where threshold meets sill to stop water as well as air.
Do Not Forget the Odd Doors
Whole-house draft-proofing means covering the doors nobody thinks about. The attic hatch is often a bare piece of drywall or plywood venting conditioned air into a 130°F or 20°F attic — glue rigid foam board to its back (R-10 worth costs about $15) and add foam tape to the lip. The garage-to-house door is a fire-rated door that still needs perimeter seals and a sweep. The garage door itself takes a $60 to $80 foam panel insulation kit plus a new bottom seal, worthwhile if the garage is attached or heated. Pet doors deserve a look too; upgrade flimsy single flaps to a dual-flap or airtight-insert model in winter.
What Draft-Proofing Actually Saves
Air sealing is one of the few efficiency upgrades with a payback measured in months. Sealing the leaks around two exterior doors typically trims $30 to $80 a year off combined heating and cooling bills in a mixed climate — more in Minnesota, less in San Diego — against a material cost under $50. Compare that to a new insulated door at $500 to $2,500 installed, which mostly makes sense when the slab is failing anyway. Comfort gains arrive faster than the dollar savings: eliminating the cold air river across a floor near an entry often matters more to how a room feels than two points of thermostat.
Draft-proofing also fixes problems that are not on the utility bill. Sealed doors block dust, pollen, and insects riding the same air paths, quiet street noise noticeably, and stop the winter condensation that forms when warm indoor air leaks into a cold jamb and feeds mold in the weatherstripping groove. If any door in the house whistles in the wind, that is free diagnostic information — whistling requires a gap and pressure, and a $12 seal ends it.
One caution while you seal: houses need controlled ventilation. If your home has a fuel-burning furnace or water heater in the living space, aggressive whole-house air sealing should come with a combustion-safety check, and very tight homes rely on mechanical ventilation. Door sealing alone will not get a leaky older house anywhere near that threshold, but it is worth knowing where the project fits in the bigger air-sealing picture.
A Sensible Order of Attack
Budget from cheapest fix to most expensive, testing as you go:
- Adjust hinges and threshold so the door sits square — free
- Replace perimeter weatherstripping — $10 to $25 per door
- Add or replace the door sweep — $10 to $25
- Insulate the attic hatch and garage door — $15 to $90
- Add a storm door on the weather-facing entries — $150 to $500
- Replace the slab with an insulated fiberglass or steel unit — $500 to $2,500 installed
Most homes get 80 percent of the improvement from the first three steps and less than $50 in materials. An afternoon with a screwdriver, a utility knife, and a stick of incense is one of the highest-return projects in home improvement — and unlike attic insulation, you feel the result the same evening.