Home Improvement

Fireplace Grate With Blower: Tube Grates That Heat the Room

Fireplace Grate With Blower: Tube Grates That Heat the Room

Most open wood fires send the bulk of their heat straight up the chimney, and a standard masonry fireplace can even pull warm air out of the house while it burns. A fireplace grate with blower fights that loss by running cool room air through a set of hollow steel tubes that wrap around the fire, then pushing the heated air back into the room with a small fan. It will not turn an open hearth into a sealed stove, but it can noticeably warm the space in front of the fireplace.

Expect a realistic improvement rather than a miracle. A plain log grate might deliver a small share of the wood’s energy to the room, mostly as radiant heat you feel only when sitting close. A tubular grate adds convection: air leaving the tube outlets can run well above 200°F once the fire is established, and a fan moves enough of it to warm a medium living room instead of just the first few feet of floor. Homeowners commonly report the room running several degrees warmer than with an ordinary grate on the same load of wood.

Getting that result depends on three things: a grate sized to your firebox, a fire built in the right spot, and a blower that is wired and placed safely. Each one is simple once you know what to look for, and none of them requires special tools.

How a Fireplace Grate With Blower Works

A tube grate is a row of C-shaped steel pipes, usually 1 1/4 to 2 inches in diameter, welded together so the curve cradles the logs. Cool air enters the lower openings at the front of the hearth, travels down and back under the fire, rises up the rear of the firebox and exits from the upper openings above the fire, now much hotter. Even with no fan, that natural rise creates some flow. This is why some people call any of these units a fireplace grate heater.

Adding a fan turns a gentle trickle into a steady stream. A fireplace grate fan typically mounts in a small manifold attached to the lower tube inlets, sitting on the hearth just outside the firebox opening. When it runs, it forces air through every tube at once, so the steel stays cooler, the air picks up more heat, and the warmed air throws farther into the room. Most fans are variable speed, with a rheostat or a thermostatic switch that turns the blower on once the tubes reach temperature.

Tube Grates Versus a Standard Fireplace Wood Grate

A basic fireplace wood grate is a cast iron or bar steel cradle that lifts logs off the floor so air can reach the underside of the fire. It improves combustion but does nothing to capture heat. A tube grate does both jobs. The tradeoff is that the tubes take up room in the firebox, need a reasonably deep opening, and cost more.

How This Differs From a Blower Insert

A fireplace insert is a closed, glass-fronted firebox that slides into the masonry opening and usually has its own built-in blower. Inserts are far more efficient, but they are a larger project that requires a properly sized chimney liner and professional installation. A tube grate with a fan is the open-fire option: no doors, no liner, and it moves from the hearth to the garage at the end of the season. If you want a fireplace blower for wood burning without the cost of an insert, this is the usual answer.

Tools and Materials

  • Tube grate sized to your firebox (measure first, see the sizing section)
  • Blower manifold and fan kit, if the grate does not include one
  • Tape measure and flashlight
  • Fireplace gloves rated for high heat
  • Ash shovel and a metal ash bucket with a tight lid
  • Flexible fire-resistant cord cover or hearth-safe cord routing clips
  • Working smoke alarm and carbon monoxide alarm near the room
  • Fire screen or mesh curtain that closes fully across the opening

Sizing the Grate to Your Firebox

Getting the size right matters more than any other choice. Measure three things: the width of the opening at the front, the width at the back wall (most fireboxes taper), and the depth from the opening to the rear wall. Also measure the height of the opening.

  1. Front width: The grate should leave at least 3 to 4 inches of clearance on each side so you can place logs and so the tubes do not touch the side walls.
  2. Rear width: Because the back is narrower, check the grate’s rear dimension too. A grate that fits the front but jams against the tapered sides will not sit flat.
  3. Depth: Most tube grates need 16 to 20 inches of depth. Shallow fireboxes, common in older homes, may only fit models with fewer or shorter tubes.
  4. Height: The tube outlets should sit below the lintel so hot air flows into the room instead of being drawn straight up into the smoke chamber.

Tube count usually runs from 5 to 9. More tubes move more air but need a wider opening. For a typical 36-inch fireplace, a 7-tube unit is a common fit; a 30-inch box often takes 5 or 6.

Setting Up a Fireplace Grate With Blower Step by Step

Do the first setup with the fireplace completely cold, ideally a full day after the last fire.

  1. Clean out the firebox. Shovel ash into a metal bucket with a lid and store it outdoors on a noncombustible surface, away from the house, for several days. Hot coals can hide in ash for longer than most people expect.
  2. Inspect the firebox. Look for cracked firebrick, gaps in mortar joints, or a damaged damper. A cracked firebox is a fire risk with or without a grate.
  3. Place the grate. Center it with the curved tubes facing into the room and the lower inlets at the front. Leave room at the back so the rear tubes do not press against the brick.
  4. Attach the blower manifold. Slide it over the lower inlets and secure it with the supplied clips or bolts. The fan housing should sit on the hearth extension, not inside the firebox.
  5. Route the cord. Run the cord along the floor away from the opening and away from where embers might land. Keep it off the hearth surface in front of the screen.
  6. Plug in directly. Plug the fan directly into a wall outlet. Do not use an extension cord or a power strip.
  7. Close the screen. Confirm your fire screen still closes fully with the manifold in place. Some setups need a screen with a notch or a slightly wider frame.
  8. Build the first fire small. Light a modest fire, let the tubes heat for 15 to 20 minutes, then switch the blower on low and work up.

Electrical and Fire Safety Near the Hearth

Combining a live flame and an electric motor in the same spot calls for care. Use a fan rated for fireplace use and listed by a recognized testing lab such as UL or ETL. The motor should sit outside the firebox where it stays cool, and the cord should never touch hot steel. Check the cord before each season for cracked insulation, melted spots or a loose plug, and replace the fan rather than taping a damaged cord.

Plug the blower directly into a wall outlet. If no outlet is near the fireplace, do not run a long extension cord across the floor. Adding a new outlet is a job for a licensed electrician, who can also tell you whether a GFCI or AFCI outlet is required in that location. If you ever need to work on an existing outlet or swap a switch, turn off the breaker and confirm power is off with a non-contact voltage tester before touching anything, and never work on powered wires. Hardwired blower kits should be installed by an electrician as well.

Fire and Carbon Monoxide Precautions

  • Keep combustibles such as rugs, furniture, baskets of kindling and holiday decor at least 3 feet from the opening.
  • Install carbon monoxide alarms on every level and near sleeping areas. Open fires can spill smoke and CO into the room when the draft is weak.
  • Have the chimney inspected and cleaned annually by a certified chimney sweep. Faster, hotter fires with a tube grate can loosen creosote.
  • Never leave the fire unattended, and switch off the blower before you go to bed or leave the house.
  • Burn only seasoned hardwood. Wet wood creates more creosote and coats the tubes, which reduces heat transfer.
Looking to buy Fireplace Grate With Blower? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Getting the Most Heat From the Grate

A few habits make a big difference. Build the fire toward the back of the grate so flames lick the rear tubes, which is where most of the heat exchange happens. Keep the fire moderately sized; an oversized fire just sends more heat up the flue and can overheat the steel. Open the damper fully while lighting, then partly close it once the fire is established if your fireplace drafts well, but never close it so far that smoke enters the room.

Glass doors, if your fireplace has them, can be left open with the screen closed while the blower runs. Some homeowners add a tempered glass door set designed to work with tube grates, but check the manufacturer’s directions; many glass doors are not meant to stay closed against a roaring open fire. Cracking a nearby window slightly can also help if the house is tight and the fire struggles to draw.

Troubleshooting Common Problems

The Blower Runs but the Air Is Barely Warm

The fire may be too small or sitting too far forward. Rebuild it toward the rear tubes and give it more time to heat the steel before turning on the fan. Also check that the outlets are not blocked by ash or a log.

Smoke Comes Out of the Tube Outlets

This usually means a tube has cracked or rusted through, or the outlets sit too high in the opening. Stop using the grate and inspect it cold. A cracked tube should be replaced, not patched.

The Fan Is Noisy or Rattles

Ash and dust build up on fan blades. Unplug the fan, let everything cool, and vacuum the housing. A grinding sound often means worn bearings, and the motor should be replaced.

The Fan Stops Mid-Burn

Many fans have a thermal cutoff that shuts the motor down if it overheats. Move the manifold farther from the opening if possible and make sure the motor housing is not sitting in direct radiant heat.

Cost Ranges

Expect these general ranges, which vary by tube count, steel thickness and region:

Item Typical Range
Tube grate without fan About $100 to $300
Tube grate with blower kit About $250 to $600
Add-on fan or replacement motor About $80 to $200
New outlet near the hearth (electrician) About $150 to $400
Annual chimney sweep and inspection About $150 to $350

Heavier steel tubes last longer and resist warping, so a mid-priced unit with thick walls is often a better value than a thin bargain model that sags after a season or two.

When to Call a Professional

Call a certified chimney sweep before the first season with a new grate if your chimney has not been inspected recently, if you see cracked firebrick, or if smoke regularly spills into the room. Call a licensed electrician if you need an outlet near the fireplace or want a hardwired fan. If you want much more heat than an open fire can provide, a hearth professional can evaluate whether an insert or freestanding stove makes more sense for your home.

Frequently Asked Questions

Do tube grates really heat a room?

Yes, within limits. A tube grate with a fan can warm a living room by several degrees compared with a regular grate, but it will not heat a whole house the way a closed insert or stove can.

Can I use a fireplace grate with blower in a gas fireplace?

No. Tube grates are designed for wood fires in masonry or wood-rated fireplaces. Gas fireplaces have their own log sets and burners, and adding a grate can interfere with safe combustion.

Is it safe to leave the blower running overnight?

No. Turn the blower off and never leave an open fire unattended or burning while you sleep.

Will a tube grate work without a fan?

It will, through natural convection, but the heat output is noticeably lower. A fan multiplies the airflow and makes the warm air reach farther into the room.

How long does a tube grate last?

A heavy-walled steel grate used normally can last many seasons. Thin tubes may warp or crack sooner, especially if fires are consistently oversized.