The biggest mistake with a slot drain is not the drain itself. It is setting the body at the wrong height, so the tile ends up proud of the grate or the grate sits in a puddle. Installing a linear drain is mostly a game of planning heights and slopes before any mortar is mixed, then bonding the waterproofing to the drain flange so water has nowhere to go but down the channel.
Part of our Bathroom Remodeling & Flooring guide — explore the full guide →
Here is the core sequence: choose wall or entry placement, connect the drain body to a properly vented 2-inch drain line, set its height so the finished tile will sit flush with or just above the grate, build a single-plane slope from the far wall down to the channel, then bond the shower membrane to the drain’s flange and flood test. A linear strip drain lets you use large-format tile on the floor because the floor slopes in only one direction, which is a big part of its appeal.
The buying decision (cost, looks, cleaning) is a separate topic. The steps here assume you have already chosen a linear drain and want to install it correctly.
Installing a Linear Drain: Planning Placement
Linear drains come in two main placements, and each changes how you build the floor.
Wall placement
The drain runs along the back or side wall of the shower. The floor slopes away from the entry toward the wall, which keeps water away from the glass and the bathroom floor. Some drains have a flange that ties directly into the wall waterproofing, and a few designs use a tile-in grate that nearly disappears. Wall placement is the most popular choice for walk-in showers.
Entry placement
The drain runs across the shower entry, usually in curbless designs, so the floor slopes from the back wall toward the opening. It captures water before it reaches the bathroom floor, but it also means stepping on the grate as you enter. Entry placement often requires recessing the subfloor so the bathroom floor and shower floor meet at the same height.
Whichever you pick, the channel should span the full width of the shower, or within a couple of inches of each wall. A shorter channel forces the floor into a more complex compound slope and reduces the main benefit of a linear strip drain. Check the drain’s flow rating against your showerhead output, especially if you plan multiple heads or body sprays.
Tools and Materials
- Linear drain body with grate (a stainless steel linear shower drain is the most common and corrosion-resistant choice)
- Drain pipe and fittings sized to code, typically 2-inch, plus a trap
- Laser level or long spirit level, tape measure and pencil
- Screed rails or wood guides for floating the mortar bed
- Dry-pack mortar (deck mud) or a preformed sloped foam tray made for linear drains
- Waterproofing membrane compatible with the drain flange, plus seam band and preformed corners
- Thinset rated for the membrane and tile, margin trowel, notched trowel
- Painter’s tape to protect the grate and channel
Many shower slot drain systems are sold as part of a matched kit that includes the sloped foam tray, membrane and bonding collar. Using a matched system makes the waterproofing much more predictable.
Single-Plane Slope Explained
Slope planning is the heart of installing a linear drain. A center drain needs four sloped triangles meeting at a point, which forces small tiles or many cuts. A linear drain needs only one plane: the entire floor tilts in one direction toward the channel. That is why large porcelain tiles work so well with them.
The standard target is 1/4 inch of fall per foot. On a shower that is 5 feet from the far wall to the drain, the floor at the far wall sits about 1 1/4 inch higher than the floor at the drain. Do the math for your shower before setting anything, because it determines both the drain height and how much the floor rises at the far side, which affects the curb or the transition to the bathroom floor in curbless builds.
A common error is sloping the floor perpendicular to the channel but forgetting to keep it flat along the channel’s length. The floor at the drain must be level side to side, or water will collect at one end of the grate.
Step-by-Step Install
- Rough-in the plumbing. Position the drain outlet so the channel lands where your layout calls for it. Many linear drains have the outlet at one end or the center of the channel, so confirm the outlet location before cutting joists or subfloor. The trap and vent must meet local plumbing code.
- Set drain height. Calculate finished floor height at the drain: subfloor plus mortar bed or foam tray at its thinnest point, plus membrane, thinset and tile. Adjust the drain body with its leveling feet or shims so the top of the grate frame ends up flush with or very slightly below the finished tile surface. Level it in both directions.
- Secure the drain. Lock the body in place with mortar or the supplied brackets so it cannot shift while the floor is built.
- Build the slope. Install screed rails from the far wall to the drain, then pack and screed deck mud to a single sloped plane, or set a preformed sloped tray. Keep the floor flat along the length of the channel.
- Bond the membrane. Once the mortar is cured enough to walk on, apply the membrane over the floor and lap it onto the drain’s bonding flange per the maker’s instructions. This is the most important seal in the shower, so use the full overlap specified and reinforce inside corners.
- Tie into the walls. Carry the floor membrane up the walls and lap the wall membrane down over it, shingle-style, so water always flows over joints rather than into them.
- Flood test. Plug the drain outlet and fill the floor to just below the curb or threshold for 24 hours, or per the membrane maker’s guidance. Mark the water line and check for drops and leaks underneath.
- Tile. Start tile at the drain edge so full or near-full tiles meet the channel neatly. Keep the tile at the drain flush with the grate frame. Grout, then seal movement joints with flexible sealant.
For a tile-in grate, set a strip of matching tile into the grate tray with thinset so the drain nearly disappears. Keep the strip slightly below the frame edge so water can still reach the slot.
Waterproofing and Mold Prevention
Linear drains use bonded waterproofing, meaning the membrane sits directly under the tile and attaches to the drain flange. Older center-drain showers used a liner under the mortar bed with a clamping ring, and mixing the two methods is a recipe for leaks. Choose one system and follow it exactly.
Moisture that gets past a poorly bonded flange soaks the mortar bed and subfloor, where it feeds mold you cannot see. Fix any existing leaks and dry out framing before starting. If demolition uncovers mold larger than about 10 square feet, or rot in joists, stop and bring in a remediation pro and possibly a carpenter. Wear an N95 respirator and gloves during tear-out, and wet-cut tile or mortar to limit dust.
Troubleshooting Linear Drain Problems
- Water pools at one end of the grate: the channel is not level or the floor slopes along the channel. Usually only fixable by removing tile and adjusting.
- Tile sits above the grate: drain body set too low. The grate frame should be flush with finished tile.
- Water runs past the drain: undersized channel for the flow, or too little slope. Check flow rating against fixtures.
- Slow draining or odor: hair in the channel or a dry trap. Lift the grate and clean the hair catcher regularly.
- Stains on the ceiling below: failure at the flange bond or a supply leak. Stop using the shower and investigate right away.
Costs and When to Call a Licensed Professional
Linear drain bodies range from under a couple hundred dollars for basic models to several hundred or more for premium stainless and tile-in designs. A professionally installed linear drain in a new tile shower often adds several hundred to over a thousand dollars compared with a center drain, mostly due to plumbing changes and precise floor prep. Curbless builds that require recessing the subfloor cost more.
Installing a linear drain in a remodel often means relocating the drain line. Moving a drain, re-trapping or re-venting is plumbing work that typically needs a permit and, in many areas, a licensed plumber. Cutting or notching floor joists to recess a curbless shower is structural and should be reviewed by a contractor or engineer. Shut off water and relieve pressure before working near supply lines. If you are unsure about the slope math, the drain height or the flange bond, a tile installer experienced with bonded waterproofing systems will often warranty the work, which is worth a lot on a second-floor bathroom.
Frequently Asked Questions
How much slope does a linear drain shower need?
Plan for 1/4 inch of fall per foot from the far wall to the drain. The floor stays level along the length of the channel.
Should a linear drain go at the wall or the entry?
Wall placement keeps water away from the glass and is the most common. Entry placement suits curbless showers and catches water before it reaches the bathroom floor.
Can I install a linear drain with a traditional mortar bed and liner?
Some drains support both methods, but most are designed for bonded waterproofing tied to a flange. Follow the drain maker’s approved method and do not mix systems.
How high should the linear drain grate sit?
The grate frame should end up flush with or very slightly below the finished tile so water flows straight in without catching on a tile edge.
Do I need a plumber to install a linear drain?
You can build the floor and waterproofing yourself, but moving the drain line, trap or vent is plumbing work that often requires a permit and a licensed plumber.