Home Improvement

Kohler Underscore Bathtub: Sizes, Depths and Install Types

Kohler Underscore Bathtub: Sizes, Depths and Install Types

Two tubs can share the same 60 by 32 inch footprint and still hold very different amounts of water, because depth, overflow height and install type change everything inside the shell. The Kohler Underscore bathtub family shows this clearly: it is a line of rectangular acrylic soaking tubs with straight, clean lines, integral lumbar support and a slotted overflow that lets the water sit higher than a standard overflow plate allows.

The short answer for most remodels: the Underscore alcove models (60 by 30 and 60 by 32 inches) replace a standard tub-shower combo with roughly 15-1/2 inches of water depth, while the drop-in models (60 by 30 up to 72 by 42 inches) sit in a deck or platform and offer deeper soaks, from about 15 inches in the smallest to 19 inches in the largest. All are acrylic and carry the maker’s plastic bath lifetime limited warranty.

The sections that follow give the specs by model, explain alcove versus drop-in and undermount, and cover installation, care and costs.

Kohler Underscore Bathtub Sizes and Specs

These figures come from the manufacturer’s current specification sheets. Model numbers end in suffixes for drain side and color, and the maker revises specs without notice, so download the sheet for your exact model before framing or ordering a door.

Model Size (L x W) Install type Water depth Capacity Drain
K-1121 60 x 30 in Drop-in or undermount 15-1/16 in 59.8 gal Reversible
K-20201 60 x 30 in Alcove, 19 in step-over 15-1/2 in 68 gal Left (LA version)
K-1956 60 x 30 in Alcove, 21 in tall 15-1/2 in 68 gal Left or right versions
K-20202 60 x 32 in Alcove, 19 in step-over 15-1/2 in 68 gal Left (LA version)
K-1130 60 x 32 in Drop-in or undermount 17-1/8 in 81 gal Reversible
K-1848 60 x 36 in Drop-in or undermount 17-1/8 in 81.1 gal Reversible
K-1136 66 x 36 in Drop-in or undermount 17-3/4 in 102 gal Reversible
K-1137 72 x 42 in Drop-in or undermount 19 in 139 gal Center

All of these shells are acrylic. Every model needs a slotted overflow bath drain, sold separately, in brass or PVC. The drop-in models are listed in White, Biscuit, Dune, Ice Grey, Thunder Grey and Black Black, while the 19-inch step-over alcove models are listed in White only. Some sizes are also sold in versions with a heated surface, which changes the model number and adds an electrical requirement.

Alcove, Drop-In and Undermount Explained

Alcove models

An alcove tub fits between three walls, with a finished front apron and a tiling flange on the back and sides. The Underscore alcove models have an integral apron and an integral flange that helps prevent water from seeping behind the wall. This is the type to pick when you are replacing a standard tub in a tub-shower combo. Searchers looking for a kohler underscore alcove tub usually want one of the 60 by 30 or 60 by 32 inch versions.

The K-20201 and K-20202 use a 19-inch step-over height while keeping the depth of a standard 21-inch bath, which makes getting in and out easier. The K-20202 is listed as ADA compliant when installed to the specific requirements of those regulations. The K-1956 alcove model stands about 21 inches tall.

Drop-in models

A drop-in tub has a rim that rests on top of a framed deck or platform, which you then finish with tile or stone. You frame the deck to a cutout size listed on the spec sheet: for example, 59-1/2 by 28-1/2 inches for the K-1121, 58-1/2 by 30-1/2 inches for the K-1130, 59-1/2 by 35-1/2 inches for the K-1848, 65 by 35 inches for the K-1136, and 70-1/2 by 40-1/2 inches for the K-1137.

Undermount option

The same drop-in shells can be undermounted, with the deck material overlapping the rim for a cleaner edge. This requires a separate undermount installation kit and a deck built from a material that can be cut and finished at the opening, such as stone or solid surface. Undermounting adds fabrication cost but makes the deck far easier to wipe clean.

Choosing the Right Model

  • Replacing a tub-shower combo: choose an alcove model in the width of your existing opening. Most older tubs are 60 by 30 inches, so measure before assuming 32.
  • Easier entry: the 19-inch step-over alcove models help children, older adults and anyone with limited mobility.
  • A deeper soak in a standard length: the 60 by 32 inch drop-in holds about 17-1/8 inches of water, noticeably deeper than the alcove versions.
  • Two bathers: the 72 by 42 inch drop-in is described as accommodating up to two people, with a center drain so both ends are comfortable.
  • Tight on hot water: the spec sheets note the hot water supply should be 70 percent of the bath’s capacity or more. A 102-gallon or 139-gallon tub can outrun a standard tank heater.

Check the floor too. Spec sheets list a minimum floor load for each model, and a large tub filled with water and a bather is heavy. The dry shells weigh from about 71 pounds (K-1121) to 105 pounds (K-1956), which makes them easier to carry upstairs than cast iron.

Installation Overview

Installation of a Kohler Underscore bathtub follows the same pattern as most acrylic tubs, but the details on the installation guide matter for the warranty. Tools and materials usually include a level, drill, framing lumber, mortar or setting compound as specified, the slotted overflow drain, plumber’s putty or gasket per the drain instructions, and a mildew-resistant silicone bathtub caulk.

  1. Shut off the water at the fixture or main and open a lower faucet to relieve pressure before disconnecting the old tub.
  2. Remove the old tub and inspect the subfloor for rot or water damage. Repair and level before going further.
  3. Confirm drain location. Alcove models are drain-specific (left or right), so match the drain end to your existing plumbing or plan to move it.
  4. Build ledgers or a deck. For alcove models, install ledger boards as the installation guide directs. For drop-in models, frame the platform to the cutout size and confirm it is level and square.
  5. Dry-fit and set. Test fit the tub, connect the drain and overflow, then set the tub in the bedding material the guide specifies so the bottom is fully supported.
  6. Fill and test. Fill the tub and check every drain joint for leaks before closing walls or tiling the deck. Leave it full while any bedding material cures if the guide calls for it.
  7. Finish and caulk. Tile down over the flange (alcove) or finish the deck (drop-in), then caulk where tile meets tub. Let the caulk cure fully before the first bath.

Plumbing changes such as moving the drain, adding a new valve or running new supply lines often need a permit and must meet local plumbing code. If you are unsure, hire a licensed plumber. Heated-surface versions also need a dedicated electrical supply, which is work for a licensed electrician; any bathroom outlet must be GFCI protected.

Looking to buy Kohler Underscore Bathtub? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Care and Cleaning

Acrylic is warm to the touch and holds heat well, but it scratches more easily than enameled cast iron. Clean with a soft cloth or sponge and a mild, nonabrasive bathroom cleaner, then rinse and dry. Avoid scouring powders, abrasive pads, and solvents such as acetone, which can dull or damage the surface. Keep hair dye and nail polish remover away from the shell. Fine surface scratches on acrylic can often be buffed out with a product made for acrylic fixtures.

Recaulk when the bead pulls away or darkens. Cut out the old caulk, clean and dry the joint, then run a fresh bead of silicone bathtub caulk with the tub filled with water so the joint is caulked at its loaded width.

Troubleshooting

The tub flexes or creaks underfoot

The bottom is not fully supported. This usually means the bedding material was skipped or did not fill the gap. It can cause cracking over time, so address it before the floor finish goes down if possible.

Water drains out before reaching full depth

Check that the slotted overflow drain is the type the spec sheet calls for. A standard overflow plate sits lower and reduces usable depth.

Gaps at the tile flange

Uneven studs or a tub that is out of level leave gaps. Shim the ledgers, re-level, and use cement board set to the flange per the installation guide.

Tub runs cold before it fills

Your water heater is too small for the tub capacity. Consider a larger or tankless heater, or choose a smaller model.

Cost Ranges and When to Call a Pro

The Underscore line sits in the mid-range for acrylic tubs. Alcove models and the smaller drop-ins are generally the most affordable, while the 66 and 72 inch drop-ins and heated-surface versions cost more. Budget separately for the drain, framing, deck materials and tile, and for labor, which often exceeds the tub price on a full tub replacement. Undermount installs with a stone deck sit at the top of the range.

Call a licensed plumber if you are relocating the drain or valve, if the old tub had leaks that damaged framing, or if you are adding a heated-surface model that needs a circuit. A general contractor helps when a drop-in deck, tile surround and floor reinforcement all need to come together.

Pick the Underscore model by your opening and soak depth, confirm the drain side and hot water capacity, and follow the installation guide closely, and the tub will feel deep, solid and quiet for years.

Frequently Asked Questions

How deep is the Kohler Underscore 60 x 32 alcove tub?

The K-20202 alcove model lists a water depth of 15-1/2 inches and a capacity of 68 gallons, with a 19-inch step-over height.

Is the Underscore available as a drop-in tub?

Yes. Drop-in models include 60 by 30, 60 by 32, 60 by 36, 66 by 36 and 72 by 42 inch sizes, and these can also be undermounted with a separate kit.

What material is the Kohler Underscore bathtub?

The Underscore models covered here are acrylic, which is lighter than cast iron and holds heat well.

What colors does the Underscore come in?

Drop-in models are listed in White, Biscuit, Dune, Ice Grey, Thunder Grey and Black Black. The 19-inch step-over alcove models are listed in White.

Does the Underscore need a special drain?

Yes. The spec sheets call for a slotted overflow bath drain, sold separately in brass or PVC, which allows the deeper water level.