Home Improvement

Ready Seal Natural Cedar: Color, Coverage and Application

Ready Seal Natural Cedar: Color, Coverage and Application

Freshly applied, Ready Seal Natural Cedar often looks darker and more orange than people expect, and plenty of first-time users worry they picked the wrong can. Give it time. This semi-transparent, oil-based exterior stain and sealer soaks into the wood rather than forming a film, and the color settles lighter over the following days as the oil penetrates. The finished look is a warm, reddish tan that brings out the natural tone of cedar and gives pine and pressure-treated lumber a cedar-like glow.

Natural Cedar is one of eight factory colors in the Ready Seal lineup, sitting between the lightest shade, Natural, and the medium browns such as Pecan. It is sold in 1-gallon cans (product 112) and 5-gallon pails (product 512). Retail listings for the 5-gallon pail commonly give about 625 square feet of coverage, or roughly 125 square feet per gallon on cedar, with real-world coverage depending on how thirsty the wood is.

The manufacturer’s FAQ says it can be applied with no temperature restrictions as long as the wood is clean and dry, which makes it more forgiving than many deck stains.

Ready Seal Natural Cedar on Cedar, Pine and Pressure-Treated Wood

This table describes how ready seal natural cedar typically looks and covers on common deck and fence woods. Coverage figures are planning estimates based on retail listings; rough, weathered or very porous wood uses more. Always test on a scrap or hidden board and judge the color after it cures.

Wood Typical look Coverage estimate Notes
Western red cedar, new Warm reddish tan; grain and color variation stay visible About 125 sq ft per gallon Let new cedar dry 2 to 4 weeks first
Cedar, weathered gray Richer and darker after cleaning Lower; weathered wood absorbs more Clean and brighten before staining
Pine, spruce or fir Golden cedar tone over a lighter base Often similar to slightly more per gallon Let new boards dry 1 to 3 weeks
Pressure-treated pine Warms and hides the green cast Varies widely by board Wait at least 1 month, 2 to 3 months recommended
Rough-sawn lumber Darker, more rustic Lowest; rough surfaces drink stain No pretreatment needed if dry and unfinished
One 5-gallon pail Fence or mid-size deck About 625 sq ft on cedar Buy extra for railings and second coats

For a quick estimate, multiply deck length by width, add board faces for railings and stairs, then divide by about 125. A 12 by 16 foot deck is 192 square feet of surface, so plan on roughly 2 gallons for the floor alone and more for rails, stairs and a second coat.

Product Facts to Know Before You Buy

Spec Value What it means
Type Semi-transparent, oil-based penetrating stain and sealer Grain shows; no film to crack or peel
Finish Flat, natural looking No gloss or plastic look
Sizes 1 gallon (112) and 5 gallon (512) Pails save money on fences and large decks
VOC Less than 250 g/L, per the manufacturer Compliant in many regulated areas; check local rules
Application temperature No restrictions, per the manufacturer Wood must be clean and at 12 percent moisture or less
Expected life 1 to 3 years horizontal, 3 to 5 years vertical Decks need recoating sooner than fences
Color mixing Can be mixed with other Ready Seal colors Blend with Natural or Pecan for a custom shade

Tools and Materials

  • Ready Seal Natural Cedar, plus about 10 percent extra for porous wood
  • Deck cleaner for weathered wood and a wood brightener for new smooth or pressure-treated boards
  • Pump sprayer for fast, even coverage on decks and fences
  • Roller with 3/8-inch nap (1/4-inch for smooth decks) or a stain pad on an extension pole
  • Natural bristle brush for rails, spindles and tight spots
  • Moisture meter (two-prong) to confirm 12 percent or less
  • Drop cloths and painter’s tape to protect siding, concrete and plants
  • Chemical-resistant gloves, eye protection and a metal can with a lid for used rags

How to Apply Ready Seal Natural Cedar

  1. Let new wood dry. Per the manufacturer: cedar about 2 to 4 weeks, pine, spruce or fir 1 to 3 weeks, and pressure-treated lumber at least 1 month with 2 to 3 months recommended.
  2. Prep the surface. Rough-cut, dry, unfinished lumber needs no pretreatment. Smooth-milled or pressure-treated boards should be brightened to open the pores, then rinsed with a hose or a pressure washer at 1,000 psi or less. Weathered gray wood should be cleaned, rinsed and brightened.
  3. Remove other finishes. Old paint, varnish or other stains must be stripped; Ready Seal will not bond over them.
  4. Wait for dry wood. Allow at least 48 hours after cleaning, longer in cool or humid weather, and check knots, corners and soft spots with the meter.
  5. Stir thoroughly. Reach the bottom of the can; shaking alone may leave pigment settled. Mix multiple containers together for consistent color.
  6. Protect surroundings. Cover plants and nearby surfaces. The stain penetrates porous concrete and stone, and overspray is hard to remove once it dries.
  7. Apply. Spray, roll or brush along the full length of a few boards at a time. The product is marketed as not leaving laps, runs or streaks, but working full board lengths still gives the most even look.
  8. Do not flood. Many projects take two coats, but over-application can leave a sticky residue, especially on dense or new wood with mill glaze.
  9. Judge color later. Expect the color to look darker at first and settle over the next couple of weeks.

A pump sprayer is the fastest tool for fences and deck floors. Work on a calm day, keep the wand low, and back-roll or pad any spots that look heavy.

Fire Safety and Oily Rags

Rags, pads and paper towels soaked with oil-based stain can heat up and catch fire on their own as they dry. Never bunch them in a pile, trash can or bag. Lay them flat outside to dry, or place them in a metal container filled with water and sealed with a lid, then dispose of them according to local rules. Keep open cans, rags and sprayer residue away from grills, fire pits, water heater pilot lights and other heat sources. If you use a battery-powered sprayer, charge it on a hard, nonflammable surface away from stain and solvents, and store the battery out of direct sun.

Use gloves and eye protection when spraying, ventilate if you stain anything in a garage or shed, and clean overspray promptly with mineral spirits while it is still wet. Store unopened product somewhere temperate; the manufacturer warns that very hot or very cold storage can separate the oils and pigments.

Looking to buy Ready Seal Natural Cedar? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Maintenance Coats

One reason homeowners like this stain is that recoating is simple. Because it penetrates rather than forming a film, there is nothing to peel or scrape when the color fades. The manufacturer recommends a light cleaning and a fresh coat about every 2 years on decks and other horizontal surfaces and every 3 to 4 years on fences and siding. After a light cleaning, allow 48 to 72 hours of drying before reapplying. You only need to strip the wood if you plan to change to a different color. Dense tropical hardwoods such as ipe may need a coat every year.

Troubleshooting

  • Too orange or red: Wait two weeks for the color to settle. For the next coat, blend in some Natural to soften it.
  • Sticky or tacky surface: Too much stain; wipe excess with a rag dampened in mineral spirits and apply lighter coats next time.
  • Blotchy pressure-treated boards: Wood was still wet or not brightened. Let it dry and recoat the light areas.
  • Footprints days later: A sign of over-application; wipe and let it cure.
  • Fading on the deck after a year: Normal for horizontal surfaces. Clean lightly and apply a maintenance coat.

Cost Ranges

A 5-gallon pail costs noticeably less per gallon than buying single cans, which is why most fence and deck projects use pails. Expect a mid-size deck to need one pail including rails and a light second coat. Professional deck staining usually runs a few dollars per square foot including cleaning and prep, with fences priced by linear foot or by side.

When to Call a Pro

Staining a deck or fence is a manageable DIY job. Consider a pro for second-story decks, large privacy fences next to neighbors’ cars or houses (overspray risk), or wood that needs stripping before it can be stained. A pro can also replace rotten boards and check deck framing and ledger attachment before you seal everything in.

Frequently Asked Questions

How much does a 5 gallon of Ready Seal Natural Cedar cover?

Retail listings commonly state about 625 square feet, or roughly 125 square feet per gallon on cedar. Weathered, rough or porous wood uses more.

Why does Ready Seal Natural Cedar look so dark at first?

The color appears darker right after application and settles lighter as the oil penetrates over the following days, so judge it after it cures.

Can I use Ready Seal Natural Cedar on pressure-treated wood?

Yes. Let new pressure-treated lumber dry at least a month, ideally 2 to 3 months, brighten the surface, and confirm 12 percent moisture or less first.

Do I need to back brush Ready Seal?

It is marketed as not leaving laps or runs, but brushing or padding heavy spots after spraying helps the stain penetrate evenly.

How long does Ready Seal Natural Cedar last?

The manufacturer estimates 1 to 3 years on decks and other horizontal surfaces and 3 to 5 years on fences and other vertical surfaces.