Most homeowners pay between $300 and $1,400 per opening for a replacement single hung window, installed. The single hung window cost for the unit alone usually lands between about $150 and $900, and the spread comes down to three things: the size of the opening, the frame material and the glass package. A basic white vinyl window in a standard bedroom size sits at the low end, while a large fiberglass or clad wood unit with upgraded glass sits at the top.
Part of our Windows & Doors guide — explore the full guide →
Single hung windows have one fixed upper sash and one lower sash that slides up. With fewer moving parts than a double hung, they cost less to build, so they often run 10 to 25 percent cheaper than a double hung of the same size and material. That makes them a common pick for budget replacements, rental properties, new construction and second-floor rooms where cleaning the outside of the top sash is less of a concern.
- Single Hung Window Cost by Size
- Price by Frame Material
- Glass Package Upgrades and What They Add
- Installation Labor and Hidden Costs
- How to Measure and Price Your Openings
- Single Hung vs Double Hung and Other Choices
- Troubleshooting Common Quote Problems
- Safety When Handling and Installing Windows
- When to Call a Pro
- Frequently Asked Questions
Labor adds anywhere from about $100 to $500 per window for a straightforward insert replacement, and more if the installer has to remove rotted framing or replace exterior trim. Expect to pay more per window for a single replacement than for a whole-house job, since crews price in setup time.
Single Hung Window Cost by Size
Size drives price more than any other factor because larger windows use more glass, longer frame extrusions and heavier balance hardware. Window sizes are usually listed width first, then height, in inches, and the figures are rough-opening or unit sizes rounded to common stock dimensions. The ranges reflect a standard double-pane, low-E vinyl unit, which is the most common replacement choice.
| Common size (W x H) | Typical use | Unit only (vinyl) | Installed (vinyl) |
|---|---|---|---|
| 24 x 36 in | Bathrooms, small kitchens | $150 to $300 | $300 to $600 |
| 24 x 48 in | Hallways, narrow walls | $170 to $330 | $320 to $650 |
| 28 x 54 in | Bedrooms, dining rooms | $200 to $380 | $350 to $700 |
| 32 x 54 in | Bedrooms, living rooms | $220 to $420 | $380 to $750 |
| 36 x 60 in | Living rooms, egress bedrooms | $260 to $500 | $420 to $850 |
| 36 x 72 in | Tall living room walls | $320 to $600 | $500 to $1,000 |
| Custom size | Older homes, odd openings | Add 15 to 40 percent | Add 15 to 40 percent |
Older homes often have openings that do not match stock sizes. Many manufacturers build replacement windows to the exact inch at little or no premium, but some charge more for anything outside their standard grid, and lead times stretch from a few days to six or eight weeks.
Price by Frame Material
Frame material is the second big lever. It affects not only the purchase price but also maintenance, lifespan and how well the window insulates.
| Frame | Unit only | Installed | Notes |
|---|---|---|---|
| Vinyl | $150 to $600 | $300 to $1,000 | Lowest cost, no painting, good insulation |
| Aluminum | $100 to $400 | $250 to $800 | Slim frames, conducts heat, common in mild climates |
| Wood | $350 to $900 | $600 to $1,400 | Classic look, needs paint or stain upkeep |
| Clad wood | $400 to $1,000 | $700 to $1,500 | Wood inside, low-upkeep cladding outside |
| Fiberglass | $350 to $900 | $600 to $1,400 | Very stable, paintable, long service life |
| Composite | $300 to $800 | $550 to $1,300 | Wood-fiber blends, stiff and low upkeep |
Vinyl
Vinyl dominates the single hung market because it is cheap to make, never needs paint and insulates well thanks to hollow chambers in the frame. White is the cheapest color. Tan, clay and dark exterior colors cost more, and dark exterior vinyl needs a heat-resistant formulation or a laminate to avoid warping in strong sun.
Aluminum
Aluminum single hung windows are still common in the South and Southwest, in manufactured homes and in budget new builds. They are strong and slim, but aluminum moves heat quickly. If you buy aluminum in a climate with real winters, look for a thermally broken frame, which adds cost but cuts condensation and heat loss.
Wood, clad wood and fiberglass
Wood windows suit historic homes and rooms where the interior trim matters. Clad wood adds an exterior shell that sheds water and holds its finish. Fiberglass costs about the same as wood but expands and contracts at a rate close to glass, so seals stay tight over decades. Single hung designs are less common in these premium materials, so your choices may be narrower than with vinyl.
Glass Package Upgrades and What They Add
The glass is where a window earns its energy savings. Most replacement single hung windows come standard with double-pane, low-E glass and argon gas fill, and that is the right baseline for most of the country.
- Double-pane, low-E, argon: the standard package; included in most quotes.
- Triple-pane: adds roughly $50 to $200 per window; worth it in cold northern climates or next to busy roads where you want sound reduction.
- Climate-tuned low-E coatings: coatings that block more solar heat help in hot, sunny regions; some cost $20 to $80 extra.
- Tempered glass: adds roughly $40 to $150 per window and is often required near tubs and showers, near doors and in very low windows. Your installer or local building department will tell you which openings need it.
- Obscure or privacy glass: adds about $30 to $100, common in bathrooms.
- Grilles between the glass: add about $30 to $120 per window, depending on pattern.
Look at the energy performance label on any window you price. A lower U-factor means better insulation, and a lower solar heat gain coefficient means less heat from the sun. Matching those numbers to your climate does more for comfort than chasing the most expensive glass.
Installation Labor and Hidden Costs
Labor depends on the installation method. An insert, or pocket, replacement sets a new window inside the existing frame and is the fastest and cheapest option, typically $100 to $300 per window. A full-frame replacement strips the opening to the rough framing, which costs more, roughly $250 to $600 per window, but lets the installer fix rot, add insulation around the frame and flash the opening properly.
Other charges that show up on quotes:
- Exterior trim or capping: $50 to $200 per window to wrap the old wood trim in aluminum or install new trim.
- Interior trim and stool repair: $50 to $150 per window if the old casing is damaged during removal.
- Rot repair: $100 to $500 or more per opening, depending on how far the damage goes.
- Disposal: often $10 to $50 per window, sometimes bundled.
- Upper-story access: second-floor windows can add $50 to $150 each for ladders or staging.
- Permits: some towns require a permit for window replacement, especially when the opening size changes; fees vary widely.
A whole-house job of 10 to 15 vinyl single hung windows commonly lands between $4,000 and $12,000 installed, depending on sizes, glass and how much trim work the house needs.
How to Measure and Price Your Openings
Accurate measurements make quotes comparable and prevent ordering the wrong size. A good locking window measuring tape with a stiff blade makes the job faster and more precise.
- Measure the width of the existing frame from jamb to jamb at the top, middle and bottom. Use the smallest number.
- Measure the height from the head jamb down to the sill at the left, center and right. Again, use the smallest number.
- Check for square by measuring both diagonals. If they differ by more than about 1/4 inch, mention it to the installer, since the opening may need shimming or full-frame work.
- Note the glass needs for each opening, such as tempered glass near a tub or privacy glass in a bathroom.
- List the room and floor for each window, which helps the installer plan access and egress requirements.
- Get at least three quotes that spell out frame material, glass package, installation method, trim work and warranty, so you can compare like for like.
Your measurements help you budget, but most installers re-measure before ordering. That is normal and protects you from paying for a window that does not fit.
Single Hung vs Double Hung and Other Choices
Choosing single hung over double hung saves money, but it is worth knowing what you give up. The fixed upper sash cannot tilt in, so cleaning the outside glass on upper floors takes a ladder or a long-handled tool. Ventilation is also limited to the bottom half of the window. On the plus side, the fixed top sash seals tightly, which can mean slightly better air-tightness than a double hung of similar quality.
Sliding windows cost about the same as single hung and suit wide, short openings. Casement windows cost more, often 20 to 50 percent above single hung, but seal tightly and open fully for ventilation. Picture windows are cheaper per square foot because they do not open at all, and they pair well with operable single hung units on either side.
Troubleshooting Common Quote Problems
- Quotes vary wildly: check whether one quote is insert installation and another is full-frame. That alone can explain a gap of several hundred dollars per window.
- The price seems low: confirm the quote includes low-E glass, argon, screens, disposal and exterior trim. Missing items get added later.
- The sash will not stay up after installation: the balance may be set wrong for the sash weight; this is a warranty adjustment, not a reason to accept a faulty unit.
- Drafts around the new window: gaps between the frame and the opening were likely not insulated or sealed fully. Low-expansion foam and exterior sealant should be part of the job.
- Condensation between panes: a failed seal. Most reputable makers cover glass seal failure for many years, so keep your paperwork.
Safety When Handling and Installing Windows
Glass is heavy and unforgiving. Wear cut-resistant gloves and eye protection when removing old sashes, and carry larger units with two people. Never flex a glass unit or set it down on a corner, and never strike the edge of a pane, since edge damage can cause it to break later. Openings near tubs, showers, doors and floors usually require tempered glass, so do not swap in plain glass to save money.
For upper-floor windows, ladder safety matters. Set the ladder on firm, level ground at about a 4-to-1 angle (one foot out for every four feet of height), keep three points of contact and never overreach. Windows on the second story and above are best left to a pro with proper staging or interior-access methods.
When to Call a Pro
A handy homeowner can install an insert single hung window on the ground floor in an hour or two once the old sashes are out. Call a professional installer when you see soft or rotted framing, when the opening is out of square, when the window is on a second story, when you need to change the size of the opening or when the wall holds a header you cannot see behind. A pro also handles flashing and egress requirements for bedroom windows, which matter for both safety and code compliance. Factory warranties sometimes require certified installation, so read the warranty before deciding to do it yourself.
Frequently Asked Questions
How much does a single hung window cost installed?
Most installed prices run from about $300 to $1,400 per window. Standard vinyl sizes with double-pane, low-E glass usually fall between $300 and $1,000, while wood, clad wood and fiberglass units reach the top of the range.
Are single hung windows cheaper than double hung?
Yes. A single hung window typically costs 10 to 25 percent less than a double hung of the same size and material because only the bottom sash moves and the hardware is simpler.
What is the cheapest single hung window material?
Aluminum and white vinyl are the least expensive. Vinyl usually offers better insulation for a similar price, which makes it the more popular choice in most climates.
Is triple-pane glass worth the extra cost?
It pays off most in cold climates and noisy locations. In mild regions, a good double-pane, low-E window with argon gives most of the comfort benefit for less money.
How long do single hung windows last?
Quality vinyl and fiberglass single hung windows commonly last 20 to 40 years. Wood windows can last longer with regular painting and caulking, while bargain units may show worn balances or failed seals sooner.