Cost Guides

Window Reglazing Cost: Restore Old Sashes or Replace?

Window Reglazing Cost: Restore Old Sashes or Replace?

Cracked, crumbling putty around old single-pane windows makes many homeowners assume the whole window is shot. Usually it is not. The wood sash underneath is often old-growth lumber that will outlast any replacement if it is kept sealed. Understanding window reglazing cost helps you decide whether to restore those sashes for a fraction of the price of new windows or move on to replacement.

The quick answer: as a general range, professional reglazing typically runs about $100 to $400 per sash, depending on size, number of panes, condition and paint. A full restoration that adds wood repair, new weatherstripping and rebalanced sash cords often lands around $300 to $800 per window. A DIYer can reglaze a sash for roughly $20 to $50 in materials plus a few hours of work. Full window replacement, by comparison, commonly runs $600 to $1,500 or more per opening installed.

Reglazing makes the most sense when the sash wood is sound and you value the original character. Replacement wins when the frames are badly rotted, you need major energy upgrades, or lead hazards make restoration impractical.

What Affects Window Reglazing Cost

Reglazing means removing old glazing putty and glazier’s points, cleaning the rabbet (the ledge the glass sits on), priming the wood, setting the glass with new points, and applying fresh glazing compound. Several factors push the price up or down:

  • Number of panes (lights): A one-over-one sash is far quicker than a six-over-six or a divided-light sash with twelve small panes. Pros often price per pane for divided lights.
  • Condition of the old putty: Brittle putty pops out quickly. Hard, well-bonded putty may need heat or careful chiseling, which takes time.
  • Broken glass: Replacing a cracked pane adds glass cost, and restorers often try to source wavy antique glass, which costs more.
  • Paint and lead: Lead-safe containment, testing and cleanup add labor and disposal cost.
  • Wood repair: Rot at the bottom rail or joints requires epoxy consolidation or dutchman patches.
  • Access: Upper-story sashes that must be removed and carried down cost more.
  • Curing and painting: Glazing compound needs time to skin over before paint, which can require a second visit.

Reglaze Window Cost: DIY vs Professional

Doing it yourself is very affordable in materials. A typical DIY shopping list runs $20 to $50 per sash, though the first one or two take much longer than later ones. Expect two to four hours per sash for a beginner, not counting paint dry time.

A pro handles removal, glass repair, priming and glazing, and may offer painting. Many restoration specialists work in their shop, which improves quality and lets them handle several sashes at once. Here is a general comparison:

  • DIY reglazing: About $20 to $50 per sash in materials; time is the main cost.
  • Pro reglazing only: Roughly $100 to $400 per sash.
  • Full window restoration cost: Often $300 to $800 per window, including wood repair, weatherstripping and sash cord work.
  • Sash replacement kit: New sashes and jamb liners in the existing frame, often $300 to $900 per window.
  • Full replacement window: Commonly $600 to $1,500 or more installed.

Adding interior or exterior storm windows to a restored sash can bring energy performance close to a double-pane unit for less money, and storms protect the new putty.

Lead and Asbestos: Test Before You Scrape

This is the most important safety step. Paint on windows in homes built before 1978 frequently contains lead, and windows are one of the worst sources because friction and scraping create fine dust. Older glazing putty itself can also contain lead, and some older putty and caulks contain asbestos.

  • Test first. Use a lead test kit on the paint and putty, or hire a certified inspector. For asbestos, send a sample of the old putty to an accredited lab before disturbing it.
  • Use lead-safe practices. Work on plastic sheeting, mist surfaces to keep dust down, and avoid dry sanding, open-flame torches and high-temperature heat guns (above about 1,100°F). Low-temperature infrared heaters and steam are safer for softening putty.
  • Protect yourself. Wear a properly fitted P100 respirator, disposable coveralls and gloves. Keep children and pregnant people away from the work area.
  • Clean properly. Use a HEPA vacuum and wet wipes. Never sweep or use a household vacuum on lead dust.
  • Hire certified help. If you hire a contractor for pre-1978 homes, choose an EPA lead-safe certified firm. If asbestos is confirmed, use a licensed abatement professional.

Tools and Materials for DIY Reglazing

  • Window glazing compound (oil-based putty or acrylic glazing)
  • Glazier’s points and a point driver
  • Stiff putty knife, 5-in-1 tool and a glazing knife
  • Low-temperature softening tool or steam setup
  • Boiled linseed oil or oil-based primer for the rabbet
  • Cut-resistant gloves and safety glasses
  • Replacement glass cut to size if a pane is cracked
  • Plastic sheeting, HEPA vacuum and a P100 respirator
  • Exterior paint for the finished glazing

How to Reglaze an Old Wood Sash

  1. Test for lead and asbestos and set up containment based on the results.
  2. Remove the sash from the frame if possible and lay it flat on a padded bench.
  3. Soften and remove old putty gently. Pull glazier’s points with pliers.
  4. Remove the glass carefully. Wear gloves and eye protection. Lift the pane straight out without flexing it, and carry large panes with two people.
  5. Clean and prime the rabbet. Scrape loose material, then apply linseed oil or primer so the wood does not suck the oil out of new putty.
  6. Bed the glass. Lay a thin bead of compound in the rabbet, press the glass in, and set points every 6 to 8 inches.
  7. Apply the glazing. Roll compound into a rope, press it along the edge, and tool a clean 45-degree bevel with the glazing knife.
  8. Let it cure and paint. Wait the time the compound requires, often one to three weeks for oil putty, then paint, lapping the paint about 1/16 inch onto the glass to seal it.

If the sash must be worked in place, practice ladder safety: firm level footing, a 4-to-1 ladder angle and three points of contact. Leave second-story exterior work to a pro with staging.

Looking to buy Window Reglazing Cost? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Ways to Keep Window Reglazing Cost Down

Several simple choices can lower the window reglazing cost without cutting corners. Batch the work: restorers often charge less per sash when they take a whole elevation or the entire house at once, because setup, containment and travel are spread across more units. Saving and reusing the original glass also helps, since antique wavy panes are expensive to replace.

You can split the work with a pro, too. Some homeowners remove and reinstall the sashes themselves and pay a specialist only for the glazing and glass repair in the shop. Others have the pro reglaze and then handle the final painting after the compound has cured. Ask any contractor whether they offer this kind of partial service.

Maintenance is the cheapest strategy of all. Inspect the putty every year or two and touch up small cracks and bare spots before water gets behind the glazing. A sash that is repainted on schedule may go decades before it needs a full reglaze.

Restore or Replace: A Decision Guide

  • Restore if the sash wood is mostly solid, the house has historic character, and you can add storms for efficiency.
  • Use a sash kit if the frame is good but the sashes are badly rotted.
  • Replace if the frames and sill are rotted through, the window is far out of square, or you want maintenance-free units.

Troubleshooting Common Reglazing Problems

  • Putty cracking quickly: The rabbet was not primed, or the compound was painted too soon or too late. Prime bare wood every time.
  • Putty will not stick: Surface was dusty or damp. Clean and dry before applying.
  • Paint peeling off glazing: Compound had not skinned over. Follow cure times closely.
  • Rattling glass: Too few points. Add more before glazing.

When to Call a Pro

Bring in a window restoration specialist for divided-light sashes, rotted joints, antique glass you want to save, or upper-floor windows. If testing confirms lead or asbestos and you are not equipped for containment, hire certified professionals. Their price is often far less than full replacement, and the result can last decades.

Frequently Asked Questions

How much does it cost to reglaze a window?

As a general range, pros charge about $100 to $400 per sash for reglazing, while DIY materials run roughly $20 to $50 per sash. Divided-light sashes and lead-safe work raise the price.

Is reglazing cheaper than replacing windows?

Usually yes. Reglazing and restoration typically cost a fraction of a full replacement window, especially if the original wood sash is in good shape.

How often do windows need reglazing?

Well-applied, well-painted glazing often lasts 20 years or more. Repainting the exterior every several years extends its life significantly.

Can old window putty contain asbestos?

Some older glazing putty and caulk does contain asbestos, and old window paint often contains lead. Test before scraping or heating it.

How long does glazing compound take to cure before painting?

Traditional oil-based putty often needs one to three weeks to skin over, while some acrylic glazing can be painted much sooner. Always follow the product label.