A failed window seal on a double-pane unit can raise your heating and cooling costs by 10 to 25 percent for that single window, and once condensation collects between the panes it never fully dries out. Window seal replacement sounds like a weekend DIY project, but the term actually covers two very different repairs: replacing the insulated glass unit (IGU) inside the frame or replacing the weatherstripping gaskets around the sash. Understanding which one you need determines whether you spend $90 or $900 per window.
Part of our Windows & Doors guide — explore the full guide →
- How to Tell Which Seal Failed
- IGU Replacement: What It Costs
- Weatherstripping Replacement as DIY
- When the Whole Window Needs Replacing
- DIY IGU Replacement for the Handy Homeowner
- Common Mistakes That Shorten New Seal Life
- Warranty Considerations
- Window Sealant Replacement: Redoing the Caulk Around the Frame and Glass
How to Tell Which Seal Failed
Two kinds of seals exist on most residential windows. The first is the hermetic seal between the two or three panes of glass, filled with argon or krypton gas for insulation. The second is the perimeter weatherstripping between the movable sash and the frame. Each fails differently and requires a different fix.
Signs of a failed IGU seal include persistent fog or moisture between panes, cloudy film or streaks that cannot be wiped away, and a noticeable decrease in insulation performance. You will feel cold radiating off the glass in winter even if no air is leaking.
Signs of failed perimeter weatherstripping include visible drafts when you hold your hand near the sash, whistling noises on windy days, rain infiltration at the sill, and daylight visible around the sash when closed.
IGU Replacement: What It Costs
If only the sealed glass unit failed, you do not need a whole new window. A glass shop can pop out the old IGU and install a new one in the existing frame. Expect to pay:
- $180 to $380 per window for standard double-pane IGUs under 30 by 48 inches
- $300 to $650 for larger units up to 36 by 72 inches
- $450 to $1,100 for triple-pane units or tempered safety glass
- $80 to $150 labor per unit if the frame is accessible from inside
Turnaround from ordering to installation runs 2 to 4 weeks since glass shops fabricate units to size. Get measurements in thirty-seconds of an inch; anything off causes installation headaches.
Weatherstripping Replacement as DIY
Replacing perimeter gaskets is within reach for most homeowners with basic tools. Double-hung, casement, and slider windows each use slightly different strip profiles.
- Identify the profile. Bring a 2-inch section of the old stripping to a big-box store or match the manufacturer’s part number online. Pella, Andersen, and Marvin all sell OEM replacements.
- Open the sash fully and peel the old weatherstripping out of its track. Most snap into a kerf cut into the sash or frame.
- Clean the channel with isopropyl alcohol to remove old adhesive residue and dirt.
- Measure and cut the new stripping to length. Allow about 1/8 inch of compression at each corner.
- Press the new strip into the channel starting at one corner. Work toward the opposite end with steady pressure.
- Close and latch the sash. Check for uniform compression by holding a flashlight outside at night.
Cost per window runs $8 to $35 for materials. Plan 45 to 90 minutes per window for first-timers.
When the Whole Window Needs Replacing
Some situations make partial repairs a waste of money. Replace the entire window if:
- The frame shows rot, warping, or structural damage
- The window is more than 25 years old and single-pane
- Multiple windows have failed on the same elevation, pointing to systemic installation issues
- The sash balance, operator, or hardware is obsolete and parts are unavailable
- You are already repainting, residing, or doing a major remodel
A full vinyl replacement window installed runs $450 to $1,200 for standard sizes. Fiberglass and wood replacements run $800 to $2,400. Andersen 400 Series, Marvin Elevate, and Pella Impervia all perform well in the $900 to $1,600 range.
DIY IGU Replacement for the Handy Homeowner
Replacing a sealed glass unit yourself saves the $80 to $150 installation labor. The process is straightforward but requires patience and the right tools.
- Remove the interior stops or glazing beads with a stiff putty knife. Work carefully to avoid splitting the wood or snapping vinyl clips.
- Cut any remaining silicone or glazing compound around the IGU perimeter.
- With a helper, lift the old unit straight out and set it on a padded surface.
- Test-fit the new IGU. Leave roughly 1/8 inch of gap around the perimeter.
- Apply setting blocks at the bottom corners to support the unit’s weight.
- Bed the IGU in a bead of 100 percent silicone or butyl glazing tape.
- Reinstall the stops and secure with brads or vinyl clips.
- Tool the exterior glazing with a caulk smoothing tool for a weathertight finish.
Skip DIY if the window is on an upper story where ladder work gets dangerous, or if the IGU weighs over 50 pounds. Professional installers use suction cups and lift aids that prevent cracked glass.
Common Mistakes That Shorten New Seal Life
A fresh seal can fail within 12 months if installation details get ignored. Watch for these pitfalls:
- Sealing in a damp or dusty frame, which prevents adhesion
- Overtightening stops against the IGU and pinching the perimeter seal
- Skipping setting blocks, which lets the unit’s weight crack the seal over time
- Using the wrong silicone. Only neutral-cure silicones rated for glazing work. Acid-cure bathroom silicone will attack the IGU’s spacer
- Painting over weep holes in the sill, which traps moisture inside the frame
Warranty Considerations
Most major window manufacturers offer 10 to 20-year IGU warranties, but the warranty only covers the glass unit, not labor. File a claim with the manufacturer before ordering third-party replacements. Andersen, Pella, and Marvin all have online portals where you enter the etched identification code from the spacer bar. If the window is under warranty, the new IGU ships free.
Window Sealant Replacement: Redoing the Caulk Around the Frame and Glass
There is a third seal on most windows that often fails first: the exterior caulk between the window frame and the siding or trim, plus the cap bead where glass meets sash on some windows. If you feel drafts around the outside of the frame, see water stains on the interior trim, or notice cracked, shrunken, or missing caulk outside, window sealant replacement is often the right fix, and it costs far less than a new IGU.
How to Replace Window Seals on a House Exterior
- Pick a dry day within the temperature range printed on the sealant label. Most sealants will not bond well to cold or damp surfaces.
- Cut out the old caulk completely with a utility knife or caulk removal tool. New sealant does not bond reliably to old, weathered caulk.
- Clean and dry the joint. Brush out debris and wipe the surfaces so they are free of dust and residue.
- Use backer rod in wide or deep gaps so the sealant forms a proper bead instead of filling a deep cavity.
- Apply an exterior-rated sealant compatible with your window frame material. Check your window manufacturer’s guidance, since some recommend specific sealant types, and as noted above, acid-cure bathroom silicone should not be used where it touches an IGU.
- Tool the bead smooth and leave the weep holes at the bottom of the frame open so water inside the frame can drain.
How to Reseal a Glass Window
To reseal a glass window, first identify how the glass is held. Older single-pane wood sashes usually use glazing putty, which dries, cracks, and falls out over time. Replace it with fresh glazing compound, not silicone, so it can be painted and matches the original method. Modern double-pane windows typically use a factory seal and glazing tape or beads. A thin exterior cap bead can be renewed with a compatible sealant, but no sealant will fix fog between the panes; that is an IGU replacement.
Safety note for older windows: Homes built before 1978 may have lead-based paint on window frames, sashes, and old glazing putty. Test before scraping or sanding, work wet rather than dry, and hire a lead-safe certified contractor if the test is positive. Use a stable ladder for exterior work, and leave upper-story windows to a professional.