Home Improvement

1×3 Actual Size: Real Dimensions of 1×3 Furring Strips and Boards

1×3 Actual Size: Real Dimensions of 1×3 Furring Strips and Boards

The 1×3 actual size is 3/4 inch thick by 2-1/2 inches wide, not 1 inch by 3 inches. That gap catches a lot of people the first time they plan a batten wall or a furring grid and their math comes up short. The “1×3” label is a nominal size, the dimension of the rough board before it was dried and planed smooth at the mill.

Length is the one dimension that matches the label. An 8-foot 1×3 is 8 feet long, sometimes with a fraction of an inch extra. So when you plan spacing, use 2-1/2 inches for the face width and 3/4 inch for the depth, and use the stated length as is.

There is one wrinkle: inexpensive furring strips are graded and milled for hidden work, so their thickness and width can vary a little more than a clear select board. Measure a few from the stack before you commit to a tight layout.

1×3 Actual Size Chart

Here are the real dimensions you can expect, along with nearby sizes for comparison. All of these follow the same rule: nominal 1-inch boards dress to 3/4 inch thick, and widths up to 6 inches lose 1/2 inch.

Nominal size Actual size (inches) Typical lengths Common uses
1×2 3/4 x 1-1/2 4, 6, 8 ft Small trim, cleats, edging
1×3 furring strip About 3/4 x 2-1/2 (can vary slightly) 8 ft most common Furring walls and ceilings, hidden backing
1×3 select or common board 3/4 x 2-1/2 6, 8, 10, 12 ft Battens, window and door trim, frames
1×3 primed finger-joint 3/4 x 2-1/2 8, 12, 16 ft Painted trim, board and batten
1×4 3/4 x 3-1/2 6, 8, 10, 12 ft Casing, baseboard caps, wider battens
2×3 1-1/2 x 2-1/2 8 ft and stud lengths Non-load-bearing partition walls

One quick way to remember it: a 1×3 is the same width as a 2×3 stud, just half as thick. That makes it handy for packing out a wall or building shallow frames that line up with 2×3 framing.

Why a 1×3 Is Not 1 Inch by 3 Inches

Lumber is sawn green from the log at close to its nominal size. Drying shrinks it, and then the mill planes all four faces smooth so the boards are straight and consistent. Those two steps remove about 1/4 inch from the thickness and about 1/2 inch from the width. The industry kept the old nominal names because everyone already used them, and grading standards set the dressed sizes that stores sell today.

Rough-sawn lumber from a small sawmill is the exception. A rough 1×3 might really measure close to 1 inch by 3 inches, with a fuzzy, uneven surface. If you are matching old work or buying from a local mill, measure rather than assume.

Furring Strips vs Select 1×3 Boards

The same nominal size is sold in very different grades, and choosing the right one saves money or saves frustration depending on the job.

Furring strips

Furring strips are the economy grade. They are usually softwood such as spruce, pine or fir, and they may have knots, wane (bark edges), slight twist and rough patches. They are meant to be covered by drywall, paneling or siding. They are sold in big bundles at the lowest price per foot, and they are often stacked outside or in open racks, so their moisture content can be higher.

Select and common boards

Select boards are clear or nearly clear pine or poplar with sharp, square edges. They are straighter and more consistent in size, which is what you want for anything visible. Common boards sit in between: fewer defects than furring, but more knots than select.

Primed finger-joint boards

Finger-joint boards are short pieces glued end to end and primed. They stay straight, cost less than clear select pine, and are ideal for painted trim and batten walls. They are not for stain, since the joints show.

How to Measure and Plan With 1x3s

  1. Measure the actual stock. Use a tape measure on three or four pieces. Furring strips in particular can run a hair under 3/4 inch or a bit narrow.
  2. Plan spacing with the real width. For a batten wall, add 2-1/2 inches per batten, not 3 inches. On a 120-inch wall with 7 battens, the battens alone cover 17-1/2 inches.
  3. Allow for the 3/4-inch depth. Furring adds 3/4 inch to the wall or ceiling thickness, which changes window and door jamb depth, outlet box depth and trim reveals.
  4. Buy 10 percent extra. Knots, splits and twisted pieces are common in furring bundles. Select boards need less waste allowance.
  5. Acclimate the wood. Let boards sit in the room for a few days before you install them, especially furring strips that were stored outside.
  6. Fasten into framing. For furring, nail or screw into studs or joists at 16 or 24 inches on center. For battens, use construction adhesive plus finish nails.

Common Uses for 1×3 Lumber

Furring walls and ceilings. Strips fastened across joists or a masonry wall give drywall or paneling a flat, nailable surface. On concrete or block basement walls, use treated or rot-resistant strips where moisture is possible, and fasten with masonry screws.

Board and batten. A 2-1/2-inch batten is a popular proportion on interior accent walls and on exterior siding, wide enough to read clearly but not bulky.

Window and door trim. A 1×3 works for simple flat casing on smaller openings or as a stool apron. Many people prefer 1×4 for main doors and 1×3 for closets.

Frames and cleats. Picture frames, cabinet face frames, shelf cleats, screen frames and light-duty boxes all make good use of the size.

Rain screens and siding battens. Furring strips create the vented air gap behind some siding systems. Use treated or naturally durable wood outdoors and follow the siding maker’s instructions.

Looking to buy 1×3 Actual Size? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Reading Labels and Picking the Right Grade

Store labels list the nominal size, so a tag that reads “1 in. x 3 in. x 8 ft.” still means the 1×3 actual size of 3/4 by 2-1/2 inches. Some stores now add the actual dimensions in smaller print, which helps when you compare boards from different bins. Species and grade are usually printed too: furring, common, select or primed finger-joint.

Match the grade to how the board will be seen and how it will be finished:

  • Hidden backing or furring: furring strips. Straightness matters more than looks, so sight down each piece and reject badly bowed ones.
  • Painted trim or battens: primed finger-joint stock for straightness and lower cost.
  • Stained trim or furniture-style frames: select pine or poplar, chosen for grain you like.
  • Exterior battens or rain-screen strips: treated or naturally rot-resistant wood, or a composite trim board in the same 1×3 actual size.

Before you check out, run a tape measure across the width and thickness of one board from each grade. A few seconds of checking avoids a layout that is off by an inch across a long wall.

Troubleshooting Common Problems

The boards are not all the same width. Furring strips are not held to tight tolerances. Sort the bundle and use the most consistent pieces where a gap or reveal will show, and keep the odd ones for hidden backing.

Battens bowed after installation. Usually the wood was not acclimated or was fastened only with adhesive. Add finish nails every 12 to 16 inches into studs and use straighter finger-joint stock next time.

Splitting when nailing near the ends. Thin 3/4-inch stock splits easily. Predrill near the ends, keep fasteners at least 3/4 inch from the end, or use a brad nailer with thinner fasteners.

Drywall screws missing the furring. At 2-1/2 inches wide, a furring strip gives you a decent target, but mark the strip centers on the floor and ceiling before hanging sheets.

General Cost Ranges

Furring strips are the cheapest 1×3 option, typically priced at roughly a dollar or two for an 8-foot piece, with bundles cheaper per foot. Common pine 1×3 boards cost more, and clear select pine or poplar can run several times the price of furring per foot. Primed finger-joint boards usually sit between common and select. Prices swing with region and lumber markets, so compare per linear foot, not per piece.

For a typical 12-foot accent wall in board and batten, the 1×3 battens themselves are usually a modest part of the budget compared with paint, adhesive and a backer panel if you use one.

When to Call a Pro

Most 1×3 projects are friendly to a careful DIYer. Bring in a carpenter if furring a ceiling or wall changes how doors, windows or cabinets fit, or if you are furring out a wall to add insulation and need to plan vapor and moisture control. For exterior siding or rain-screen work, a siding contractor will know the flashing and fastening details your local code expects. Any change that involves moving outlets, switches or boxes forward to meet the new wall surface should be handled by a licensed electrician.

Frequently Asked Questions

What is the actual size of a 1×3?

A standard dressed 1×3 measures 3/4 inch thick by 2-1/2 inches wide. The length matches the label, such as 8 feet.

Are 1×3 furring strips the same size as 1×3 boards?

Nominally yes, about 3/4 by 2-1/2 inches. Furring strips are a lower grade with looser tolerances, so individual pieces can be slightly thinner or narrower.

How long are 1×3 furring strips?

Eight feet is the most common length. Select and primed 1×3 boards come in more lengths, often 6 to 12 feet and sometimes 16 feet.

Is a 1×3 the same width as a 2×3?

Yes. Both are 2-1/2 inches wide. The 2×3 is 1-1/2 inches thick, twice the 3/4-inch thickness of a 1×3.

Can I use 1x3s for board and batten?

Yes, a 2-1/2-inch batten is a common size. Primed finger-joint stock stays straight and takes paint well for painted walls.

Why do 1x3s measure smaller than their name?

The name is the rough-sawn size. Drying and planing all four faces smooth reduce the board to its finished 3/4 by 2-1/2 inch size.