Nothing dates or cheapens a kitchen faster than doors that sag, gap, or slam, and the culprit is almost always the cabinet hardware hinges. Choose the right style, mount them correctly, and a set of doors hangs dead-straight for 20 years. Get them wrong and you’ll be chasing crooked reveals every few months. After hanging thousands of doors, here’s what actually matters.
Part of our Kitchen Remodeling guide — explore the full guide →
This guide breaks down the main hinge types, how overlay differs from inset, what the 35mm cup measurement means, and the step-by-step for measuring, adjusting, and replacing cabinet hardware hinges without a service call.
- The Main Hinge Types
- Overlay vs. Inset: Know Which You Have
- Understanding the 35mm Cup
- How to Measure for Replacement
- Adjusting Hinges in 3 Directions
- Replacing Hinges Step by Step
- Opening Angles and Special Situations
- Add-On Soft-Close vs. Built-In
- Tools and Prep Before You Start
- When to Replace vs. Repair
The Main Hinge Types
Walk into any hardware aisle and the choices look overwhelming. In practice, nearly every kitchen uses one of these:
- Concealed (European) hinges: The modern standard. The entire hinge hides inside the cabinet when the door is closed. It seats in a 35mm bored cup on the door and clips to a mounting plate on the cabinet. Runs $2 to $8 per hinge.
- Face-frame hinges: Built for cabinets that have a solid wood frame around the box opening. The mounting plate screws to the frame edge rather than the interior side wall.
- Frameless (full-overlay) hinges: For European-style boxes with no face frame, the plate mounts directly to the cabinet’s interior side panel.
- Wrap-around and semi-concealed: Older or budget styles where part of the hinge shows. Common on Shaker and traditional builds.
The single most useful upgrade you can buy is a soft-close concealed hinge. The built-in hydraulic damper catches the door in the last few inches and closes it silently. A set of soft-close hinges runs $4 to $10 apiece and eliminates slamming for good.
Overlay vs. Inset: Know Which You Have
Hinges are specified by how the door sits relative to the cabinet box. Buy the wrong overlay and the door either won’t close or leaves a huge gap.
- Full overlay: The door covers almost the entire box edge. Doors sit nearly edge to edge with little gap. Most common in new frameless kitchens.
- Half (partial) overlay: Two doors share a center partition, each covering half of it. Typical in older framed cabinets.
- Inset: The door sits flush inside the frame opening, level with the face. The most precise, most expensive look. Requires a hinge specifically rated for inset.
To identify yours, open a door and look at the closed neighbor. If the door face sits proud of the frame, it’s overlay. If it drops flush into the opening, it’s inset. Concealed hinges are sold with a “crank” number (0mm, 9mm, 16mm) that sets the overlay, so match it.
Understanding the 35mm Cup
Almost every concealed hinge on the market uses a 35mm cup, the round recess drilled into the back of the door. This is the industry standard, and it’s why replacement hinges swap in so easily.
- The cup bore is 35mm in diameter and roughly 11mm to 13mm deep.
- The center of the cup sits about 3mm to 6mm from the edge of the door (the “bore distance”), which affects how the door clears the box.
- Boring a fresh cup takes a 35mm Forstner bit and a drill press or a jig, but if a cup already exists, you can drop a new hinge straight in.
If your existing doors already have 35mm cups, you can upgrade plain hinges to soft-close in an afternoon with a screwdriver, no drilling required.
How to Measure for Replacement
Bringing the right hinge home saves a second trip. Before you buy, record these:
- Frame vs. frameless: Reach inside. A solid wood lip around the opening means face-frame; a bare box edge means frameless.
- Overlay measurement: Close the door and measure how far it laps over the box edge, from door edge to where the box begins.
- Cup diameter: Measure the round recess. If it’s 35mm, you’re on the standard.
- Opening angle: Standard hinges open to 110 degrees. If your cabinet sits next to a wall or in a corner, you may need a 155-degree hinge.
Take an old hinge to the store and match it. Brand matters less than most people think, since the 35mm cup and standard plate spacing make many brands interchangeable.
Adjusting Hinges in 3 Directions
The best feature of European hinges is that they adjust after installation. Two or three small screws let you dial the door in without unmounting anything. Give yourself 10 minutes with a Phillips driver:
- Side to side (depth/overlay): The rear screw moves the door left or right to even out the center gap between paired doors. A quarter turn shifts it roughly 1mm to 2mm.
- In and out (depth): The middle screw pulls the door tight to the box or pushes it out, fixing a door that rubs or stands proud.
- Up and down (height): On many hinges this is set at the mounting plate. Loosen the plate screws, nudge the door, retighten.
Work one door at a time and eyeball the reveal lines against the neighboring door. A whole kitchen of misaligned doors can be squared up in under an hour.
Replacing Hinges Step by Step
Swapping tired hinges for new soft-close units is one of the easiest kitchen upgrades there is:
- Open the door and unclip or unscrew the hinge arm from the mounting plate.
- Remove the two screws holding the cup in the door and the two holding the plate to the box.
- Seat the new hinge cup in the existing 35mm bore and drive the screws.
- Screw the new plate to the box using the old holes, or shift slightly and pre-drill fresh pilots.
- Clip the arm to the plate, close the door, and run the three-way adjustment until the reveals are even.
Budget $30 to $80 to re-hinge an average kitchen of 20 doors with soft-close hardware. It’s a Saturday job that makes a whole kitchen feel new.
Opening Angles and Special Situations
Standard hinges open to about 110 degrees, which works for most doors. But real kitchens have corners, appliances, and tight spots where the standard hinge fails. Match the hinge to the location:
- 155-degree wide-angle hinges: For cabinets beside a wall or a fridge, where a door needs to swing clear so drawers or pull-outs fully extend.
- Corner and bi-fold hinges: For blind-corner or lazy-Susan cabinets where two doors fold together.
- Zero-protrusion hinges: For inset doors next to a wall so the door doesn’t bind on the trim.
- Push-to-open hinges: For handleless, slab-front designs. A light press pops the door instead of a pull.
Before you buy a whole set, walk the kitchen and note any door that opens next to an obstruction. Those spots need the wide-angle version even if the rest of the room takes standard hinges.
Add-On Soft-Close vs. Built-In
If your existing hinges are fine but you just want the quiet, you have two paths. The choice comes down to budget and how much you value a clean look:
- Built-in soft-close hinges: Replace the whole hinge with a unit that has the damper integrated in the arm. Cleanest result, nothing visible, $4 to $10 each.
- Clip-on damper adapters: Small cylinders that snap onto an existing hinge arm and cushion the close. Around $2 to $4 each, no hinge swap needed, but they’re visible when the door is open.
For a kitchen you’re keeping, I go with full built-in soft-close hinges. The adapters are a fine quick fix for a rental or a fast flip where budget rules.
Tools and Prep Before You Start
A hinge job goes smoothly with the right handful of tools on the bench. You don’t need a shop full of equipment, but skipping these turns a quick swap into a frustrating afternoon:
- #2 Phillips screwdriver: The workhorse. A stubby version helps in tight cabinet corners.
- Cordless drill with a clutch: Set it low so you seat screws without stripping the softwood inside the cabinet.
- 35mm Forstner bit: Only if you’re boring fresh cups. Pair it with a hinge-boring jig to control depth and edge distance.
- Painter’s tape and a pencil: Mark plate positions so a full row of cabinets ends up consistent.
- A 4-foot level or a straightedge: To sight your reveals across a run of doors.
Lay the doors on a padded surface, not the floor, so the finish doesn’t scratch while you work. Label each door with tape if you remove several, because even matched doors have slightly different adjustment once they’re back up.
When to Replace vs. Repair
A hinge that squeaks or slams doesn’t always need replacing. A drop of oil silences a squeak, and the adjustment screws fix most sag. Replace the hinge outright when the metal is bent, the cup has stripped out of the door, or you simply want the soft-close feature. Because they’re cheap and standardized on the 35mm cup, replacing a full set of cabinet hinges is usually the smarter move over fighting with worn-out ones door by door.