A surprising number of homeowners buy a screen door, carry it home and find it is half an inch too wide for the opening. Custom screen doors solve that problem by building the frame to your exact measurements, but they are not always necessary. Most exterior doorways in American homes match one of a handful of stock sizes, and a standard door costs much less and ships right away.
Part of our Windows & Doors guide — explore the full guide →
The quick answer: if your opening measures close to 32 by 80 or 36 by 80 inches for a hinged door, or 48 by 80 inches for one panel of a sliding patio door, start with a standard size. Most stock doors include expander strips or adjustable frames that absorb small differences. Go custom when the opening is narrower or wider than the expanders allow, taller than 80 inches, out of square by more than a small amount, or when you want a specific style, color or heavy duty frame that stock lines do not offer.
- Standard Sizes Before You Order Custom Screen Doors
- How to Measure Your Opening
- What Custom Adds Beyond Fit
- Standard vs. Custom: A Decision Guide
- Installing a Screen Door
- Troubleshooting Fit Problems
- Cost Ranges
- When to Call a Pro
- Large Screen Doors for Wide and Tall Openings
- Frequently Asked Questions
Measuring is where most mistakes happen, so it gets its own section. Get those numbers right and the standard versus custom decision usually makes itself.
Standard Sizes Before You Order Custom Screen Doors
Manufacturers build to the most common door openings, which is why the same few sizes show up on every store shelf. Knowing them saves you from paying for custom work you do not need.
Hinged screen doors
- 32 by 80 inches: common on back doors, side doors and older homes. An aluminum screen door 32 x 80 is one of the most widely stocked sizes.
- 36 by 80 inches: the standard modern front entry. A hinged screen door 36 x 80 fits most newer homes built in the last few decades.
- 30 by 80 and 34 by 80 inches: less common but still available in many product lines.
Stock 36×80 screen door models are usually designed for an opening a bit larger or smaller than the nominal number. Many have a Z-bar or expander that lets them fit openings within roughly half an inch to an inch of the listed size. Check the box or spec sheet for the actual fit range before buying.
Sliding screen doors
Sliding patio doors use a separate screen panel that rides in a track. A 48 x 80 sliding screen door matches one panel of a common 8 foot wide (96 inch) slider. Other frequent widths are 36 and 60 inches, and many adjustable sliding screens fit a height range of about 77 to 81 inches. Because patio door brands use slightly different track profiles, measuring the track height accurately matters as much as the width.
How to Measure Your Opening
Take three width measurements and two height measurements. Openings are rarely perfectly square, especially in older houses, and the smallest numbers are the ones that count.
- Find the mounting surface. Hinged screen doors usually mount to the outside edge of the door jamb or brick molding. Measure between the inside edges of the jamb where the screen door will sit.
- Measure width at top, middle and bottom. Use a steel tape and record each number to the nearest eighth of an inch.
- Measure height on the left and right. Go from the top of the threshold (sill) to the underside of the head jamb.
- Check for square. Measure both diagonals, corner to corner. If they differ by more than about a quarter inch, the opening is out of square and an expander or custom frame will help.
- Note the hinge side. Decide which side the hinges go on and whether the handle will clear the main door knob and any storm hardware.
- For sliders, measure the track. Measure from the bottom of the upper track channel to the top of the lower track rail, then measure the opening width where the screen panel will cover it.
Write everything on one sheet with a quick sketch. When you order custom, the supplier will ask if your numbers are the opening size or the finished door size. Give opening sizes unless they specifically ask otherwise, and let them deduct the clearance.
What Custom Adds Beyond Fit
Fit is the main reason people order custom, but the made-to-measure route opens up other choices that stock doors rarely offer.
- Frame material and thickness. Heavier extruded aluminum, solid wood or steel frames instead of thin roll-formed aluminum. Thicker frames resist bending and last longer on busy doors.
- Screen type. Standard fiberglass, fine mesh for small insects, solar screen for sun control, or heavy pet-resistant mesh.
- Style. Mid-rails, kick panels, decorative grilles, arched tops or full view designs that match the house architecture.
- Color matching. Custom powder coat colors to match trim, rather than the three or four stock finishes.
- Hardware upgrades. Better closers, keyed latches, heavier hinges and adjustable bottom sweeps.
For historic homes, custom wood screen doors are often the only way to match period details. Wood doors need paint or finish and more upkeep, but they give the traditional look that aluminum cannot imitate.
Standard vs. Custom: A Decision Guide
| Your situation | Best choice |
|---|---|
| Opening within the expander range of a stock size | Standard |
| Opening more than an inch off any stock size | Custom |
| Opening taller than 81 inches | Custom |
| Diagonals differ noticeably | Custom or stock with wide expanders |
| Rental or budget project | Standard |
| Historic home or specific design | Custom |
If you are close to a standard size, one trick is to adjust the opening rather than the door. Adding a strip of trim to one side of a slightly oversized opening lets a stock door fit cleanly. Planing a jamb to widen an opening is riskier, so leave it to experienced hands.
Installing a Screen Door
Standard and custom hinged doors install much the same way. Gather a drill, screwdriver bits, a level, a tape measure, a hacksaw (for trimming expanders), shims and the hardware included with the door.
- Dry-fit the door in the opening and confirm the hinge side.
- Attach the hinge rail or Z-bar to the jamb, keeping it plumb with a level.
- Hang the door and check the gap along the latch side. Adjust the hinge rail if the gap tapers.
- Cut the latch-side expander or drip cap to length if supplied, then fasten it.
- Install the handle and latch, then position the strike so the latch catches without slamming.
- Mount the closer to the door and the jamb, and set the speed so the door closes fully without banging.
- Adjust the bottom expander or sweep to close the gap at the threshold.
Sliding screens are simpler. Set the top of the panel into the upper track, lift it, swing the bottom in and lower it onto the lower rail. Adjust the rollers with the screws at the corners until the panel glides evenly and closes against the jamb.
Troubleshooting Fit Problems
- Gap at the latch side. The hinge rail is out of plumb. Loosen, shim and re-fasten.
- Door rubs the threshold. Raise the bottom expander or check for a sagging top hinge.
- Latch will not catch. Move the strike slightly or add a shim behind it.
- Sliding screen jumps the track. Clean the track, then raise the bottom rollers so they ride firmly on the rail.
- Screen bows out. Re-roll the spline with fresh spline cord one size larger, or order replacement mesh cut to size.
Cost Ranges
Basic stock aluminum screen doors are among the most affordable exterior upgrades, often costing under a few hundred dollars. Mid-range stock doors with heavier frames and better hardware cost more. Custom screen doors typically start at a few hundred dollars and climb to well over a thousand for solid wood, decorative designs or heavy duty frames with specialty mesh. Sliding screen panels follow a similar pattern, with stock adjustable panels far cheaper than custom ones built to a specific track.
Installation by a handyman or door company generally adds a modest labor charge for a straightforward opening. Custom orders also include a measuring visit in many cases, and lead times of a few weeks are common, so plan ahead of bug season.
When to Call a Pro
Most homeowners can measure for and install a stock screen door in an afternoon. Bring in a pro if the opening is badly out of square, the jamb is soft or rotted, you are ordering an expensive custom door (many suppliers guarantee fit only when they measure), or the door mounts to brick or stucco. A pro measurement is cheap insurance against a custom door that arrives the wrong size and cannot be returned.
Large Screen Doors for Wide and Tall Openings
Large screen doors cover openings wider than a single 36 inch door or taller than 80 inches, such as French doors, double entry doors, oversized sliders and garage openings. Most need a custom frame, a pair of hinged doors, or a retractable or roll-up screen. The right choice depends on the width, how often the opening is used and whether the screen must stay out of sight when not in use.
Options by opening size
| Opening | Typical size range | Common screen solutions |
|---|---|---|
| Oversized single entry | 38 to 42 inches wide, or taller than 81 inches | Custom hinged screen door with a heavy frame |
| Double or French doors | About 60 to 72 inches wide | Pair of hinged screen doors, or a double retractable screen meeting in the middle |
| Wide sliding patio doors | Three- and four-panel sliders, 9 feet and wider | Multiple sliding screen panels or custom panels built to the track |
| Folding or multi-slide glass walls | Often 10 feet and wider | Motorized or manual retractable screens in a side or head housing |
| Garage doors | Single or double garage width | Roll-up or zippered garage screen systems |
What changes as doors get bigger
- Frame strength: Thin roll-formed aluminum flexes on a wide or tall door. Choose extruded aluminum, steel or solid wood, and add a mid-rail or kick panel to stop racking.
- Hinges and closers: A large door is heavier, so use three or four hinges and a closer rated for the door weight. Pairs of doors need an astragal or overlapping strip where they meet.
- Screen tension: Wide panels of mesh bow more. Heavier pet-resistant mesh or a mid-span support keeps it flat.
- Wind: Large screens catch wind. Retractable systems with side guides and hinged doors with good latches resist being blown open.
Measuring large openings
Follow the same three-width, two-height method, but also check that the head jamb is level across the full span, since a slight sag over 6 or more feet affects fit. For retractable screens, measure the depth of the jamb or trim where the housing mounts. For any custom large door, many suppliers prefer to measure on site, which also secures their fit guarantee. Expect costs at the upper end of custom pricing, and longer lead times than standard sizes.
Frequently Asked Questions
What size screen door do I need for a 36 inch door?
A 36×80 screen door is designed for a standard 36 inch entry. Measure the actual opening between the jambs, because many stock doors are sized to fit an opening slightly larger than 36 inches.
Can I cut down a screen door to fit?
Expander strips and drip caps can be trimmed, but the main frame of an aluminum door generally cannot be cut without weakening it. If the opening is too far off, order a custom door.
How long do custom screen doors take?
Lead times vary by maker and season, commonly from one to several weeks. Order in late winter or early spring to beat the rush.
Are custom screen doors worth the extra cost?
They are when the opening is an odd size, you want a specific look, or you need a sturdier frame. For a standard opening, a quality stock door is usually the better value.
What is a standard sliding screen door size?
A common size is 48 by 80 inches for one panel of an 8 foot patio door, with 36 and 60 inch widths also available. Always measure the track height before ordering.