Most deck collapses do not start with a rotten post or a cracked joist. They start where the deck meets the house. A ledger board for deck framing carries roughly half the load of an attached deck, and when it is nailed on, bolted into the wrong material or left without flashing, it can pull away with no warning while the deck is full of people.
Part of our Decks & Outdoor guide — explore the full guide →
The short answer: use a pressure-treated ledger at least as deep as your joists (2×8 is the usual minimum, 2×10 or 2×12 for larger decks), fasten it to a solid house rim joist with 1/2 inch through-bolts, lag screws or code-listed structural ledger screws in a staggered pattern, flash it so water never reaches the rim, and add lateral load tension ties that connect the deck joists to the house floor framing. Never rely on nails alone, and never hang a ledger on brick veneer, stucco over foam, or a cantilevered floor overhang.
- How a Ledger Board for Deck Framing Works
- Ledger Size: 2×6 vs 2×8 vs 2×10
- What the House Side Must Be
- Tools and Materials
- Step-by-Step: Attaching Ledger Board to House
- Deck Ledger Bolts and Screw Spacing
- Lateral Load Tension Ties
- Flashing and Water Management
- Troubleshooting Common Ledger Problems
- Cost Ranges
- When to Call a Licensed Professional
- Frequently Asked Questions
- What size ledger board for deck framing do I need?
- Can I use lag screws instead of through-bolts?
- Do I need to remove siding to install a ledger?
- How many tension ties does a deck need?
- Is a 2×6 ledger board ever allowed?
- What is the difference between a deck ledger and a rim joist?
- Should deck ledger flashing be metal or vinyl?
Building departments look at the ledger first on almost every deck inspection, so getting it right also keeps your permit moving. Sizing, fastener choice and spacing, flashing, tension ties and the cases where a freestanding deck is the smarter choice all matter.
How a Ledger Board for Deck Framing Works
A ledger is a single board bolted flat against the house band (rim) joist. Joist hangers attach the deck joists to its face, so every pound of decking, furniture, snow and people on the house half of the deck passes through the hangers, into the ledger, through the fasteners and into the house framing. That chain is only as strong as its weakest link, and the weakest link is usually the fasteners or the rim they bite into.
Two different forces act on the connection. Vertical load pushes straight down and tries to shear the bolts. Lateral load, from people moving, swaying or a crowd shifting to one side, tries to pull the deck away from the house. Bolts and screws handle the vertical load well. Lateral load is why modern codes call for separate tension ties.
Ledger Size: 2×6 vs 2×8 vs 2×10
A simple rule works for nearly every residential deck: the ledger should be at least as deep as the joists it supports. If your joists are 2×8, use a 2×8 ledger. If they are 2×10, the ledger should be 2×10 or deeper so the full joist hanger has solid wood behind it.
- 2×6 ledger board: Most prescriptive deck codes do not allow it for a typical attached deck because there is not enough depth for a staggered bolt pattern with proper edge distance. You may see 2×6 ledgers on small landings or on old decks, but they are usually a red flag at inspection.
- 2×8 ledger board: The common minimum. Works with 2×8 joists on decks with modest spans.
- 2×10 and 2×12: Used with deeper joists and longer spans, and they give more room for fastener rows.
Use pressure treated ledger board lumber rated for ground contact or at least for exterior use where it will stay damp. Even with good flashing, the ledger lives in a wet zone next to the siding line. Choose a straight board with no large knots in the bolt zone, and crown it so any slight bow faces up.
What the House Side Must Be
The fasteners need something solid to grab. The house band joist should be solid-sawn 2x lumber or an engineered rim board at least about 1 inch thick, sitting on a foundation or a bearing wall. Check from inside the basement or crawlspace before you drill a single hole.
Do not attach a ledger to:
- Brick or stone veneer, which is only a facing tied loosely to the wall.
- Hollow concrete block without engineered anchors and approval.
- A cantilevered floor or bay window overhang, where the joists are not supported below.
- Thin or damaged rim boards, or rims you cannot see and verify.
If any of those apply, build a freestanding deck with its own beam and posts a short distance from the house, and simply let it sit close to the wall. It costs a little more in footings but removes the riskiest connection entirely.
Tools and Materials
- Pressure-treated ledger board sized to the joists
- 1/2 inch hot-dip galvanized or stainless through-bolts with washers and nuts, or 1/2 inch lag screws, or code-listed structural ledger screws
- Self-adhering flashing membrane and metal or vinyl Z-flashing
- Joist hangers rated for the joist size, with the specified hanger nails or screws
- Two lateral load tension ties and the fasteners they require
- Impact driver (a cordless impact driver makes driving structural screws and lag screws far easier and less likely to strip), drill with long bits, socket set
- Circular saw, oscillating tool or siding removal tool, level, chalk line, clamps or temporary blocks
- Safety glasses, gloves and hearing protection
Step-by-Step: Attaching Ledger Board to House
- Pull a permit. Most jurisdictions require one for an attached deck. The plan review will tell you the joist span, fastener schedule and footing depth they expect. Call 811 before digging any footings for the outer beam.
- Mark the height. Set the top of the ledger so the finished deck surface lands 1 inch or so below the door threshold, accounting for decking thickness. Snap a level chalk line.
- Remove the siding. Cut out the siding along the ledger zone so the ledger bears directly on the sheathing and rim. Never bolt over siding: it crushes, traps water and leaves a gap that weakens the bolts.
- Flash the wall. Apply self-adhering membrane to the exposed sheathing, lapping up behind the house wrap and down past the bottom of the ledger zone. Shingle-lap every layer so water runs out, never in.
- Tack the ledger in place. Hold it on the line with temporary screws or clamps. Leave a little gap at each end where needed for trim and drainage.
- Drill and fasten. Follow a staggered fastener pattern sized to your joist span. For through-bolts, drill clean holes through the ledger, sheathing and rim, then install bolts with washers on both sides. For lag screws, predrill a clearance hole in the ledger and a smaller lead hole in the rim. For structural screws, follow the manufacturer’s spacing and drive them with the impact driver until the head seats flat.
- Install top flashing. Slide Z-flashing or a formed cap over the ledger and under the house wrap or siding so water sheds over the top edge and away.
- Hang the joists with full-depth hangers and every specified nail hole filled. Then install the tension ties.
Deck Ledger Bolts and Screw Spacing
Fastener spacing depends on joist span: the longer the joists, the more load each foot of ledger carries and the closer the fasteners go. Your local deck guide or permit sheet will list exact spacing. As a general picture of what prescriptive codes call for:
- Through-bolts can be spaced farther apart than lag screws because a nut and washer clamp both sides.
- For short joist spans (about 6 feet), spacing can be in the range of 2 to 2.5 feet on center.
- For long spans (16 to 18 feet), spacing tightens to roughly 8 to 12 inches on center.
Stagger the fasteners in two rows: one row about 2 inches down from the top edge and the next about 2 inches up from the bottom edge, alternating along the length. Keep the end fasteners 2 to 5 inches from each end of the ledger. Staggering spreads the load and avoids splitting the board along a single grain line.
For deck ledger bolts, use 1/2 inch diameter hot-dip galvanized or stainless steel with a washer under the head and the nut. Match the coating to treated lumber; electro-plated hardware corrodes quickly in contact with modern treated wood. Structural ledger screws are a strong alternative, especially when you cannot reach the back of the rim, but they must be a type listed for ledger attachment, installed exactly at the spacing on their evaluation report.
Nails are not an acceptable ledger fastener. A ledger nailed to the rim is the classic failure behind many collapse reports.
Lateral Load Tension Ties
Bolts keep the ledger from sliding down. They do much less to stop the whole deck from pulling outward. Modern prescriptive codes add at least two lateral load connections per deck, each rated around 1,500 pounds, placed within about 24 inches of each end of the deck.
The common version is a steel tension tie. Generically, it is a heavy angle bracket with a threaded rod. One bracket bolts or screws to a deck joist; a matching bracket attaches to a house floor joist or blocking inside the basement or crawlspace; a threaded rod passes through the ledger and rim to connect the two. Some designs use a bracket on the outside face of the rim instead. Follow the tie maker’s fastener schedule exactly, since the rated capacity depends on it.
If you cannot reach the house floor framing from inside, your inspector may accept an alternative detail, such as diagonal hold-downs or a freestanding design. Ask before you build.
Flashing and Water Management
Rot behind the ledger is silent. The board can look fine from outside while the house rim behind it turns soft. Good flashing has three parts: membrane on the sheathing, the ledger bearing tight against that membrane, and a top flashing that laps under the siding and over the ledger. Some builders also add a thin spacer or washer stack to create a small drainage gap; if you do, the fastener schedule may change, so confirm with your plans.
Leave a small gap between the first deck board and the house so water can drain. Seal bolt penetrations with flashing tape or sealant patches before the ledger goes on.
Troubleshooting Common Ledger Problems
- Rim joist is not where you expected: Measure from a window or door opening inside and out. If the ledger line falls on a floor sheathing edge or a sill plate instead of the rim, adjust the deck height or go freestanding.
- Bolts hit wiring or pipes: Check the inside before drilling. If a cable runs along the rim, turn off the breaker for that circuit and confirm the power is off with a non-contact voltage tester before working near it, then shift the fastener location within the allowed pattern. Never work on powered wires.
- Old ledger looks dark or soft: Probe with an awl. If the house rim behind it is damaged, it needs repair by a carpenter before any new ledger goes on.
- Ledger bows between fasteners: Pull it tight with clamps as you go and use a straighter board next time.
- Uneven foundation wall: Shim behind the ledger only with solid, treated material and only if your fastener spec allows the gap.
Cost Ranges
For a typical 12 to 16 foot ledger, materials (treated lumber, flashing, bolts or structural screws, hangers and two tension ties) often run roughly $150 to $400. Permits vary widely by town, from under $100 to several hundred dollars for a full deck. Having a contractor install or replace a ledger on an existing deck usually costs several hundred to a couple thousand dollars, more if the house rim needs repair or siding has to be patched.
When to Call a Licensed Professional
Bring in a licensed contractor or structural engineer when:
- The deck is more than one story up, very large or will carry a hot tub or heavy planters.
- The house has veneer, block, an engineered I-joist rim or any framing you cannot verify.
- You find rot, insect damage or an old nailed-on ledger.
- The permit office asks for engineered drawings.
Anchoring into framing and footings, wind and snow loads and HOA approval all affect a deck build, so get the plan approved before work starts. Any electrical work for deck lighting or outlets belongs to a licensed electrician, and outdoor outlets need GFCI protection.
Frequently Asked Questions
What size ledger board for deck framing do I need?
Use a ledger at least as deep as your joists. A 2×8 is the common minimum, and 2×10 or 2×12 pairs with deeper joists and longer spans.
Can I use lag screws instead of through-bolts?
Yes, 1/2 inch lag screws are allowed in most prescriptive codes, but they need closer spacing than through-bolts and proper pilot holes. Listed structural ledger screws are another option.
Do I need to remove siding to install a ledger?
Yes. The ledger must bear on the sheathing and rim with flashing behind it. Bolting over siding traps water and weakens the connection.
How many tension ties does a deck need?
Prescriptive codes typically call for at least two lateral load connections, each placed within about 24 inches of the ends of the deck.
Is a 2×6 ledger board ever allowed?
Rarely for an attached deck. It lacks the depth for a staggered fastener pattern, so most inspectors expect 2×8 or larger.
What is the difference between a deck ledger and a rim joist?
The ledger is the board bolted to the house that carries one end of the joists, while the deck rim joist, also called the band board, runs across the outer ends of the joists on the far side. The rim ties the joist ends together and often carries the fascia. The ledger handles the house connection and needs flashing and structural fasteners.
Should deck ledger flashing be metal or vinyl?
Vinyl, plastic, copper, or stainless flashing are the safer choices against modern pressure-treated lumber. The copper-based preservatives in treated wood can corrode aluminum flashing that touches it. If metal flashing is used, choose a type the lumber treater rates as compatible, and always pair it with self-adhering membrane behind the ledger.