Choosing the right window style affects everything from your monthly energy bill to how the room feels when you walk in. The different kinds of windows on the market today range from the workhorse double-hung that has dominated American homes for a century to specialty bay and bow units that turn a kitchen wall into a focal point. Style choice should follow three priorities: ventilation needs, ease of cleaning, and how the window relates to the architecture of the house.
Part of our Windows & Doors guide — explore the full guide →
Double-Hung Windows
Double-hung windows have two sashes that slide vertically within the frame. Both the upper and lower sashes operate, which gives you flexible ventilation. Lower the top sash and raise the bottom for stack-effect airflow that pulls warm air out near the ceiling while drawing cooler air in below. Most modern double-hung windows from Pella, Andersen, and Marvin also tilt inward for cleaning the exterior glass from inside the house.
Expect to pay $400 to $900 per window installed for a vinyl double-hung in the 32-by-54-inch standard size. Wood-clad versions from the Andersen 400 Series or Pella Reserve run $900 to $1,800 installed. Double-hung windows fit almost any architectural style from Colonial to Craftsman to Contemporary, which is why they remain the default choice in remodels.
Single-Hung Windows
Single-hung windows look identical to double-hung from the outside, but only the bottom sash moves. The upper sash is fixed. They cost roughly 15 to 25 percent less than double-hung, which adds up across a whole-house replacement. The trade-off is harder exterior cleaning on second-story windows and slightly less ventilation flexibility.
Single-hung windows make sense in second-floor bedrooms where you rarely open the top half anyway. A typical installed price runs $300 to $700 for a vinyl unit. Pella, Simonton, and ProVia all offer reliable single-hung lines.
Casement Windows
Casement windows hinge on the side and swing outward, operated by a hand crank. They seal tighter than any hung style because the sash compresses against weatherstripping when closed. That makes them the top performer for energy efficiency. Marvin Ultimate casement windows can hit U-factors as low as 0.18 with their Tripane glass option, which translates to dramatic heating bill savings in cold climates.
Casement windows catch breezes that double-hung windows miss because the open sash acts like a scoop. The downside is they cannot be used behind walkways or decks where the swing would obstruct traffic. Installed cost runs $500 to $1,200 for a single vinyl unit, more for wood-clad and triple-pane options.
Awning Windows
Awning windows hinge at the top and open outward at the bottom, forming a small awning when open. The geometry sheds rain, which lets you keep them cracked during a storm for ventilation. They are common above and below larger fixed windows, in bathrooms, and in basements where ground-level placement makes other styles impractical.
Awning units typically measure 24 by 36 inches or smaller and cost $300 to $700 installed. Pairing two awnings stacked above or below a picture window creates an attractive architectural detail and gives you ventilation without sacrificing the view.
Sliding and Picture Windows
Sliding windows operate horizontally, with one or both sashes moving along a track. They are wider than they are tall, making them suitable for spaces above kitchen sinks or in bedrooms where a horizontal opening makes more sense than a vertical one. Installed cost ranges from $400 to $900 for a standard two-panel slider.
Picture windows do not open at all. They are pure glass framed for the largest possible view with the smallest possible frame profile. Andersen, Pella, and Milgard offer picture windows up to 96 inches wide. They cost less per square foot than operable windows because there are no moving parts, but they require pairing with operable units somewhere in the room to meet egress and ventilation code.
Bay and Bow Windows
A bay window combines three units, typically a fixed picture window in the center flanked by two operable casements or double-hung windows at angles. A bow window uses four to six units in a gentle arc. Both project outward from the house, creating a window seat or display area inside. They add architectural drama and visible square footage to a room.
Cost climbs steeply. A bay window installed runs $2,500 to $6,500 depending on size and unit quality. Bow windows can hit $4,500 to $9,000. Both require careful flashing and structural support, since the projection adds load to the exterior wall. Always hire a contractor experienced with these specific installations rather than treating it like a flat-wall replacement.
Specialty Shapes
Round, half-round, octagon, hexagon, and trapezoid windows show up in gables, stairwells, and over front doors. They are almost always fixed units used for daylight and architectural accent rather than ventilation. Custom shapes from Andersen, Marvin, or Pella add lead time of six to ten weeks and a 30 to 60 percent premium over rectangular units of similar size.
For Craftsman and Tudor homes, diamond-pattern leaded glass inserts maintain period detail. Modern and contemporary homes lean toward clean rectangular geometry without grilles or muntins.
Frame Material Decisions
Frame material is as important as window style. Vinyl is the budget pick at $300 to $800 per window installed, low maintenance, and reasonably energy efficient. Fiberglass from Pella Impervia or Marvin Elevate runs $700 to $1,400 and outperforms vinyl on dimensional stability through temperature swings. Wood-clad windows from Andersen 400 Series or Marvin Signature offer the warmth of real wood interior with a maintenance-free aluminum or fiberglass exterior, priced at $900 to $1,800.
Solid wood windows like the Marvin Ultimate line are the premium choice for historic homes and high-end builds, but they require repainting or restaining every five to seven years. Budget for $1,200 to $2,500 per window installed.
Energy Performance Numbers That Matter
Look at three NFRC numbers on every window label. The U-factor measures heat loss, where lower is better. The Solar Heat Gain Coefficient measures how much solar heat passes through the glass, where lower is better in hot climates and higher is better in cold ones. Visible Transmittance shows how much light comes through. Energy Star qualified windows in northern climates hit U-factor 0.27 or lower, while southern climate Energy Star windows prioritize SHGC at 0.40 or lower.
Triple-pane glass adds roughly 15 percent to the window cost but cuts heating loss by 20 to 30 percent compared to dual-pane. In climates with sustained winter temperatures below 20 degrees Fahrenheit, the payback is typically 8 to 12 years.