Home Improvement

Double Kitchen Sink Sizes: Widths, Bowl Splits, and Cabinets

Double Kitchen Sink Sizes: Widths, Bowl Splits, and Cabinets

Two bowls sound like twice the convenience, but a double sink that is too narrow for your cabinet or your cookware can feel like two half sinks. Most homeowners only discover this after the counter is templated and the first sheet pan will not lie flat. Understanding double kitchen sink sizes means looking at three things together: the overall width, how that width is split between the bowls, and the cabinet that has to hold it.

The short version: standard double sinks run from 30 to 36 inches wide, with 33 inches being the classic size for drop-in models and 32 to 33 inches common for undermount. Larger double sinks of 36 to 42 inches exist for big kitchens. Pair a 33 inch double sink with a 36 inch base cabinet and a 36 inch sink with a 39 or 42 inch base, and you are on solid ground.

Standard Double Kitchen Sink Sizes

When people search for standard double sink dimensions, they usually want to know which widths are stocked and what cabinet each one needs. Here are the most common sizes:

Overall width Typical front to back Minimum base cabinet
30 in 18 to 22 in 33 in
32 to 33 in 19 to 22 in 36 in
36 in 19 to 22 in 39 to 42 in
42 in and up 20 to 22 in 45 to 48 in

A standard double sink width of 33 inches by 22 inches has been the default drop-in size in American kitchens for decades. If you are replacing an old stainless double sink in a laminate counter, there is a good chance the existing cutout was made for that footprint, which makes a like for like swap easy.

Front to back, double sinks typically measure 18 to 22 inches. That leaves room for a faucet behind the bowls on a standard 25 inch deep countertop. Deeper sinks can crowd the faucet, especially with an undermount mounted close to the backsplash.

Bowl Splits: 50/50, 60/40 and Low-Divide

The split describes how the overall width is shared. It affects daily use more than the outside measurement does.

50/50 equal bowls

Two bowls of the same size. This works well if you wash in one side and rinse in the other, or if two people work at the sink together. In a 33 inch sink, each bowl is roughly 14 to 15 inches wide, which can be tight for large roasting pans.

60/40 offset bowls

One larger bowl and one smaller bowl. In a 33 inch sink, the large side is often 17 to 18 inches wide, enough for most pots, while the small side handles rinsing produce or holds a disposal. Many cooks find 60/40 the most practical split.

70/30 and 80/20 bowls

These favor a big main bowl with a small prep bowl. They suit people who mostly use one side and want the second bowl for draining or garbage disposal duty.

Low-divide sinks

A low-divide double sink has a center wall roughly half the height of the bowls, often 5 to 6 inches tall instead of the full depth. Water and soap stay separate for everyday tasks, but large pans and baking sheets can lie across both bowls. It is a good compromise if you want two bowls without giving up the ability to soak oversized cookware.

Bowl Depth and Double Sink Measurements

Most double sinks have bowls 8 to 10 inches deep. Deeper bowls hide dishes and reduce splashing, but they place the drain lower in the cabinet, which matters if you plan a garbage disposal. Some 60/40 sinks pair a 10 inch deep main bowl with a 7 or 8 inch prep bowl to save room under the smaller side.

When you read double sink measurements on a spec sheet, look for the outside length and width, each bowl’s interior size, bowl depth and the minimum cabinet size. Interior bowl dimensions are what matter for your cookware. Measure your largest pot, sheet pan and cutting board, then compare them to the bowl sizes before you choose a split.

Matching Double Sink Width to the Base Cabinet

The cabinet’s listed width is its outside dimension. Side panels and face frames reduce the usable opening by roughly 1.5 to 3 inches. The common rule is that a sink should be at least 3 inches narrower than the cabinet, which is why a 33 inch double sink usually goes in a 36 inch base.

  • 33 inch base: fits a 30 inch double drop-in or a compact undermount.
  • 36 inch base: fits a 32 to 33 inch double sink, the most common pairing.
  • 39 inch base: fits a 36 inch drop-in and some 36 inch undermounts in frameless cabinets.
  • 42 inch base: fits a 36 inch undermount comfortably or a 39 inch drop-in.
  • 48 inch base: fits large double or workstation sinks up to about 45 inches.

Undermount sinks need more care than drop-ins because the whole bowl plus flange has to pass between the cabinet sides and face frame stiles. A double bowl undermount kitchen sink in stainless steel or granite composite is a popular choice for stone counters, but confirm the minimum cabinet listed by the maker, and if your cabinets are framed, measure the clear opening between stiles.

Step-by-Step: Choosing a Double Sink Size

  1. Measure the base cabinet. Note the outside width, interior width and face frame opening.
  2. Measure the counter depth. Standard counters are 25 inches; confirm there is space behind the sink for the faucet, soap pump and any air gap.
  3. List your largest items. Sheet pans run about 18 by 13 inches; large stock pots are often 12 to 14 inches across. Make sure the main bowl handles them.
  4. Pick a split. Choose 50/50 for equal tasks, 60/40 for most cooks, and low-divide if you soak big pans often.
  5. Decide on a disposal. Plan which bowl gets it, usually the smaller one in a 60/40, and confirm under-sink clearance.
  6. Check the cutout. For replacements, measure the existing cutout and choose a sink whose rim covers it fully.
Looking to buy Double Kitchen Sink Sizes? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Troubleshooting Common Double Sink Sizing Mistakes

Pans do not fit either bowl. A 50/50 split in a 30 or 33 inch sink leaves bowls too narrow for large cookware. A 60/40 or low-divide model fixes this without changing the cabinet.

The new sink does not cover the old cutout. Drop-in replacements must be at least as large as the hole. Measure the cutout, not the old sink’s rim, and add a little margin. If the hole is too large, a laminate counter may need replacing.

The undermount will not fit between face frame stiles. Choose a narrower sink or a frameless cabinet. Trimming stiles is possible but weakens the frame if overdone.

The faucet hits the backsplash or the bowl rim. Deep front to back sinks leave little room for the faucet. A sink 19 to 20 inches deep, or a wall mounted faucet, may solve it.

The drain sits too low. Deep bowls plus a disposal can force the trap lower than the wall drain outlet. A rear offset drain or shallower prep bowl helps.

Double Kitchen Sink Sizes for Larger Kitchens

Big kitchens open up more options. Double kitchen sink sizes of 36 to 42 inches let both bowls reach a useful width, so a 60/40 model at 36 inches gives a main bowl around 20 inches across, wide enough to lay a sheet pan flat. Workstation doubles in the 42 to 45 inch range add a ledge for a sliding cutting board, drying rack and colander, turning the sink into a prep station. If you have an island and a perimeter run, some homeowners put a large double sink on the perimeter for cleanup and a small single prep sink on the island instead of one oversized double.

Keep the dishwasher in mind as you size up. A standard dishwasher is 24 inches wide and sits next to the sink base, so a wide sink cabinet can push the dishwasher, trash pullout and corner cabinets around. Sketch the whole run before choosing among the larger double kitchen sink sizes so the layout still works on both sides of the sink.

Typical Cost Ranges

Basic stainless double sinks in thinner gauges sit at the affordable end of the market. Thicker 16 or 18 gauge stainless, granite composite and fireclay double sinks cost more, and large low-divide or workstation designs land higher still. Installation adds labor for plumbing the continuous waste, connecting a disposal and, for undermounts, the fabricator’s cutout and polishing fees. Budget for a new basket strainer for each bowl and a fresh drain kit when you replace the sink.

When to Call a Pro

A same size drop-in replacement is a manageable DIY job if you are comfortable with slip joint plumbing. Changing from a single to a double sink, moving the drain or adding a disposal circuit is more involved. A licensed plumber can rework the continuous waste and trap height, and a licensed electrician should add any new outlet or circuit. Hire a stone fabricator to cut undermount openings, since a mistake in quartz or granite is expensive to fix.

Standard Double Sink Width: Outside, Bowl and Cutout Measurements

The standard double sink width for a kitchen is 33 inches overall, set in a 36 inch base cabinet. That outside number is not the same as the space inside the bowls or the hole in the counter, and mixing them up is the most common ordering mistake. Every spec sheet lists several widths, and each one answers a different question.

The Widths on a Spec Sheet

Measurement What it tells you Typical value for a 33 inch double
Overall width Outside edge to outside edge, including rim 33 inches
Bowl interior width (50/50) Usable space in each bowl About 14 to 15 inches each
Bowl interior width (60/40) Large and small bowl About 17 to 18 inches and 11 to 12 inches
Cutout width Hole in the counter Slightly less than overall width for a drop-in
Minimum base cabinet Cabinet the sink is designed to fit 36 inches

Drop-In vs Undermount Width

A drop-in sink’s rim rests on the counter, so its overall width is larger than the cutout by the rim on each side. Undermount sinks hang under the counter, so the overall width is the bowl assembly plus a small flange, and the counter opening is cut close to the bowl edge. That is why undermount doubles of 32 to 33 inches fit the same 36 inch cabinet as a 33 inch drop-in.

How to Measure Double Sink Width for a Replacement

  • Measure the existing sink rim edge to edge for the overall width.
  • Remove the sink, or check from inside the cabinet, to measure the actual counter cutout.
  • Measure the cabinet’s clear opening between face frame stiles for undermounts.
  • Note the drain spacing if you want to reuse the existing waste kit.

Double Sink Width in Bathrooms

The phrase also comes up for bathroom double vanities, which follow different standards. Double vanities are commonly 60 or 72 inches wide, and each basin is usually 16 to 20 inches across. At 60 inches, two people can use the sinks but elbow room is tight; 72 inches allows counter space between basins. Plan about 30 inches between sink centers for comfortable use, and check local code for required side clearances before setting the plumbing.

Frequently Asked Questions

What is the standard size of a double kitchen sink?

The classic size is 33 inches wide by 22 inches front to back. Undermount double sinks commonly run 32 to 33 inches. Both usually fit a 36 inch base cabinet.

Is a 60/40 or 50/50 double sink better?

A 60/40 split suits most home cooks because the larger bowl handles big pots while the smaller bowl rinses produce. A 50/50 split works well for washing and rinsing in separate equal bowls.

What size cabinet do I need for a 36 inch double sink?

A 39 inch base works for many drop-ins, but a 42 inch base is safer for a 36 inch undermount, especially in framed cabinets where the face frame narrows the opening.

What is a low-divide double sink?

It has a center divider about half the height of the bowls. You still get two separate basins, but large pans and baking sheets can rest across both sides for soaking.

How deep are double kitchen sinks?

Most bowls are 8 to 10 inches deep. Some designs use a deeper main bowl and a shallower prep bowl to leave more room for a disposal and plumbing under the sink.