Draining a pool sounds simple until you watch a fiberglass shell pop out of the ground or a vinyl liner shrink and crack in the sun. Learning how to drain pool water correctly means understanding hydrostatic pressure, picking the right pump for your volume, and knowing exactly where to send tens of thousands of gallons without flooding your neighbor’s basement. This guide walks through residential pool draining from prep through refill, with safety notes you do not want to skip.
A typical 16-foot by 32-foot inground pool holds 17,000 to 24,000 gallons. Renting a 1/2 HP submersible pump runs $40 to $70 per day, and drainage takes 10 to 18 hours at standard flow rates.
When You Actually Need to Drain
Full pool draining is rarely necessary and always carries risk. Most water-quality issues can be fixed with shock, flocculant, and aggressive filtration without removing the water. Drain only for these specific reasons.
- Calcium hardness above 1,000 ppm that cannot be corrected with partial drains
- TDS (total dissolved solids) above 3,000 ppm causing cloudy water that resists treatment
- Liner replacement on vinyl pools
- Resurfacing or major repair on plaster or fiberglass pools
- Winterization in regions where pools are drained below the skimmer line
For routine season-ending winterization, you typically lower the water 6 to 12 inches below the skimmer rather than draining completely. Save full draining for legitimate need.
Critical Warning About Pop-Up Risk
Inground fiberglass pools and some vinyl-lined pools can float out of the ground when emptied if the surrounding water table is high. The shell becomes a boat in a sea of soil-bound groundwater. Spring drains after heavy rain are the highest risk.
Check the hydrostatic relief valve (the small fitting in the main drain or deepest part of the floor) before draining. If your pool has one, it should be opened during a full drain. If it does not, drain only when the water table is verified low, usually mid-summer after a dry stretch.
Selecting the Right Pump
Your pool pump is designed to move clean water through a filter, not to fully drain the shell. Use a separate submersible pump for the job. Rental yards stock these in the $40 to $90 per day range.
A 1/2 HP submersible moves about 50 gallons per minute, draining a 20,000-gallon pool in roughly 7 hours of run time. A 1 HP pump cuts that to 4 hours but costs more to rent and requires a 20-amp circuit. For most residential drains, the 1/2 HP unit is the sweet spot.
Where to Send the Water
Local regulations dictate this. Many municipalities prohibit draining chlorinated water directly into storm drains or onto neighboring property. Sanitary sewer cleanouts accept the water in most jurisdictions but check before connecting.
If sewer discharge is allowed, hook the discharge hose to the cleanout in your yard or basement. If not, you may need to dechlorinate the water in batches by holding it in a kiddie pool with sodium thiosulfate for 24 hours before letting it run into the yard. Spreading the discharge across the lawn over many hours (not all at once) prevents drowning the grass.
Step-by-Step Draining Process
Turn off the pool pump and disconnect power at the breaker for any equipment that should not run dry. Place the submersible pump in the deep end of the pool, ideally on a milk crate or piece of plywood to keep the intake from sucking up sediment.
Route the discharge hose to your approved drainage point. Verify the hose is not kinked and the route does not climb more than 25 vertical feet (most rental pumps cannot lift higher). Plug the pump into a GFCI-protected outlet. Start the pump and watch the first 5 minutes for hose kinks, leaks, and pump performance.
Monitoring the Drain
Check on the pump every 60 to 90 minutes during draining. Look for the water level dropping evenly, the hose route holding steady, and the pump motor not overheating. Most submersibles are rated for continuous duty but failed hose connections can flood basements within minutes.
As the water gets low, the pump may start sucking air. Reposition it to the very deepest point of the pool floor. Once the pump cavitates and cannot pick up more water, switch to a smaller utility pump or a wet/dry shop vac for the final inches.
Protecting the Shell After Draining
An empty pool is vulnerable. Vinyl liners shrink in sunlight and can pull away from the track within 48 hours of full draining. Cover a drained vinyl pool with a tarp or get the new liner installed immediately.
Fiberglass and plaster pools can sit empty longer but should be inspected for hydrostatic issues daily. If you see groundwater seeping in through the main drain or shell cracks, refill the pool partially to counterbalance the pressure. Time the drain so you can complete any work and start refilling within 72 hours.
Refilling and Rebalancing
Most municipalities allow a meter-bypass credit when refilling a pool. Call your water utility before refilling to set up the sewer credit; otherwise you will be billed for sewer treatment on water that never entered the sewer.
Fill at full pressure from one source (typically a garden hose at 5 to 7 gallons per minute) for 30 to 50 hours total. Test and balance pH, alkalinity, calcium hardness, and chlorine as the water reaches operating level. Shock the pool once you reach skimmer height and run the filter continuously for 24 hours before swimmers return.