The part of installing tankless water heater systems that trips up most homeowners is not the mounting or the plumbing, it is the gas and venting. A gas tankless unit like the Rinnai RU199 or the Navien NPE-240A demands far more fuel flow than the old tank it replaces, which often means upsizing the gas line from half-inch to three-quarter-inch pipe and running dedicated stainless-steel venting. Skip those requirements and the unit starves for gas or vents dangerously. This guide walks the full sequence, from planning the utilities to the final leak check, so your installation is safe and passes inspection.
Plan the Gas, Vent, and Water Path First
Before you buy anything, confirm your home can feed the unit. A typical gas tankless heater consumes 150,000 to 199,000 BTUs, roughly four times a standard tank. That load frequently requires a larger-diameter gas line and adequate meter capacity.
Map three paths on paper: the gas supply route, the intake-and-exhaust venting route to the outside, and the cold-in, hot-out water connections. Locating the unit on an exterior wall shortens the vent run and simplifies the whole job. Getting this planning right before you cut anything is the difference between a smooth day and installing tankless water heater problems that cascade all afternoon.
Verify your gas meter can supply the extra load before you commit. A whole-home tankless unit adds roughly 150,000 to 199,000 BTUs on top of your furnace, range, and dryer. If the sum of everything running at once exceeds your meter’s capacity, the gas company may need to upsize the meter, a free but scheduling-dependent step you want to discover during planning rather than on install day. Call your utility early if you have any doubt.
Gather Tools and Materials
Assemble everything in advance so a stalled step does not leave your water off for hours. A gas install needs more specialized parts than an electric swap.
- Category III stainless-steel vent pipe and termination, or concentric venting per the model.
- Three-quarter-inch black iron pipe or CSST for the upsized gas line, plus fittings.
- Two isolation service valves with hose ports for future descaling.
- A sediment trap, gas shutoff, and thread sealant rated for gas.
- A pressure-relief valve, mounting bracket, and lag bolts into studs.
- A combustion analyzer or a manometer to verify gas pressure, plus soapy water for leak checks.
Mount the Unit
Choose a solid interior or exterior wall that keeps vent and pipe runs short and leaves the manufacturer’s required clearances. Most units specify several inches of clearance on the sides and front for service access and combustion air.
Locate the studs, attach the mounting bracket level, and hang the unit securely on lag bolts rated for its weight, typically 60 to 80 pounds. A level mount matters because the internal condensate drain relies on gravity in condensing models. Take the time to get it plumb rather than eyeballing it.
Consider what sits behind and around the unit as you position it. In an unconditioned garage or a space that can freeze, you need a model with built-in freeze protection and a plan to keep power on, since a frozen heat exchanger can crack and void the warranty. Outdoor-rated units mount on an exterior wall and skip the venting entirely, which is a popular choice in mild southern climates where freezing is rare. In freezing regions, keep the unit indoors in a conditioned space.
Connect Gas and Venting
The gas connection is the step that most demands respect. Run the properly sized supply line to the unit, install a sediment trap and a shutoff valve at the heater, and use gas-rated pipe dope on every joint. Then verify the gas pressure with a manometer under load; the burner needs the pressure the manufacturer specifies, often around 3.5 to 10.5 inches of water column.
Venting on condensing units uses Category III stainless or approved PVC per the model, terminated the required distance from windows, doors, and soffits. Never vent a gas tankless heater into an old masonry chimney unless the manufacturer explicitly allows it. Because this stage carries carbon-monoxide and fire risk, many jurisdictions require a licensed pro for the gas and venting portion of installing tankless water heater setups.
Plumb the Water Connections
With the unit mounted and gas roughed in, connect the water. Cold water ties to the inlet and hot water to the outlet, each through an isolation service valve so you can flush the heat exchanger later without draining the house.
- Install the cold-side isolation valve on the inlet, hot-side on the outlet.
- Connect the pressure-relief valve and route its discharge safely.
- For condensing units, run the acidic condensate line to a drain with a neutralizer if required.
- Open a hot fixture and purge air from the lines before firing the unit.
The isolation valves are not optional in practice; without them, the annual vinegar descaling that keeps the unit alive becomes a major plumbing chore.
Water quality deserves attention at this stage too. If your home has hard water above about 7 grains per gallon, plan to install a scale filter or a whole-home softener upstream of the heater. Scale is the number-one enemy of a tankless heat exchanger, and hard water can shorten its life dramatically even with diligent descaling. Adding a $50 inline scale cartridge now, or tying the unit into an existing softener loop, protects a heater that costs well over a thousand dollars and preserves its efficiency for years.
Electrical, Permits, and Startup
Even gas tankless units need a 120-volt outlet nearby to power the control board, igniter, and fan. Plug it in or wire the dedicated circuit per the manual. Then pull your permits; nearly every jurisdiction requires both gas and plumbing permits, and the inspection protects your insurance and resale.
At startup, open the gas, restore water, and power the unit. Check every gas joint with soapy water for bubbles and every water fitting for drips. Run hot water at two fixtures to confirm capacity and watch the display for fault codes. Set the temperature to 120°F for a safe balance of scald protection and bacteria control.
Give the first firing your full attention, because the initial startup reveals most installation errors. Listen for the igniter clicking and the burner catching smoothly rather than surging. A unit that short-cycles, throws an ignition fault, or delivers wildly swinging water temperature usually points to a gas-supply issue, either an undersized line or low pressure. Better to catch that on day one with your tools still out than to discover it during the family’s first cold shower a week later. Confirm steady temperature at a low flow as well as a high one.
DIY Versus Hiring a Professional
A confident DIYer can handle the mounting and water plumbing, but the gas line and venting are where I draw the line for most people. Improper gas work risks leaks and carbon monoxide, and improper venting can pull combustion gases back into the home. A hybrid approach works well: do the mounting and water connections yourself, and hire a licensed plumber for the gas and vent portion for a few hundred dollars.
Done right, installing tankless water heater equipment rewards you with endless hot water, lower energy bills, and an 18-to-20-year service life. Plan the utilities carefully, respect the gas and venting requirements, add isolation valves for easy maintenance, and pull the permits.
First-Year Maintenance and Break-In
Your job is not finished when the hot water flows. Register the unit with the manufacturer within the warranty window, often 30 to 90 days, or you risk losing coverage on the pricey heat exchanger. Note the model and serial number and keep the manual where you can find it, since fault codes on the display refer back to it.
Plan your first descaling for the one-year mark, sooner if your water is hard. Close the isolation valves, hook a submersible pump and a bucket of white vinegar to the service ports, and circulate it through the exchanger for 45 minutes to clear mineral scale. Clean the cold-water inlet screen at the same time, since sediment collects there and starves the flow. Homeowners who build this annual ritual into their routine are the ones whose units reach twenty years; those who skip it are the ones replacing heat exchangers early. Those habits turn a daunting project into a durable, code-compliant upgrade that pays back for two decades.
Frequently Asked Questions
How much does it cost to install a tankless water heater?
Most professionally installed whole-home gas units land in the low-to-mid thousands of dollars once the heater, labor, venting, and permits are added. The biggest swing factors are whether the gas line must be upsized, how long the new vent run is, and whether a condensate drain is needed. Electric units cost less to buy, but a large whole-house model can require new circuits or a panel upgrade that narrows the gap.
How long does it take to install a tankless water heater?
A like-for-like swap of one tankless unit for another usually takes a pro about half a day. Converting from a tank to tankless typically takes a full day or longer, because the job adds a new gas line, new venting, wall mounting, and water piping changes. Plan for inspection scheduling on top of that, since most jurisdictions require gas and plumbing permits before the work is signed off.
Can you replace a tank water heater with a tankless in the same spot?
Often yes, but rarely as a direct swap. Most gas tankless models cannot reuse the old tank’s vent, so a new vent sized and rated for the unit is needed, and the gas line frequently has to be upsized to 3/4 inch. The unit also needs a nearby 120-volt outlet and wall framing to mount on. Moving it to an exterior wall can shorten the vent run and lower the total cost.
Can you install an electric tankless water heater yourself?
The plumbing side is manageable for a confident DIYer, but the electrical side belongs to a licensed electrician. Whole-house electric tankless units draw very high current and often need two or more dedicated 240-volt circuits with heavy-gauge wire, which many older panels cannot supply without an upgrade. An electrician can confirm panel capacity, size the breakers and wire to the manufacturer’s specs, and pull the electrical permit.
Can a tankless water heater run on propane?
Yes. Buy a model built for propane (LP) or one the manufacturer allows to be converted with its own kit, since propane and natural gas units use different gas valves and orifices. Propane is supplied at a different pressure than natural gas, so the regulator and line sizing must match the unit’s rating. Gas line and regulator work should be done or checked by a licensed gas fitter.