Order a door an inch off and you will fight it every day, or worse, own an expensive slab that does not fit the hole. Getting interior door measurements right the first time is simple once you know which numbers matter: the slab size, the rough opening, the jamb width, and the swing clearances. Doors come in a handful of standard sizes, but old houses love to throw non-standard openings at you. This guide covers the standard dimensions, exactly how to measure for both slab and pre-hung doors, and the clearances that keep a door swinging freely.
Part of our Windows & Doors guide — explore the full guide →
- Standard Interior Door Sizes
- Slab vs Pre-Hung, and Why It Changes Measuring
- Measuring for a Slab Door
- Measuring the Rough Opening for Pre-Hung
- Jamb Width Matters
- Swing Clearances and Floor Gaps
- Handedness and Swing Direction
- Non-Standard and Old-House Openings
- Tools and Tips for Accurate Measuring
- How to Measure Door Size for a Replacement
Standard Interior Door Sizes
Most interior doors in American homes come in a predictable set of widths. Standard height is 80 inches, often called a 6-foot-8 door. Common widths, listed as feet and inches, are:
- 2 feet 0 inches (24 inches) for closets and small baths
- 2 feet 4 inches (28 inches) for secondary rooms
- 2 feet 6 inches (30 inches), a very common bedroom size
- 2 feet 8 inches (32 inches), the width that meets accessibility guidelines
- 2 feet 10 inches and 3 feet 0 inches (34 and 36 inches) for main and wider passages
Standard slab thickness is 1-3/8 inches for interior doors. Knowing these sizes helps you tell instantly whether your opening is standard or a custom situation.
Slab vs Pre-Hung, and Why It Changes Measuring
A slab door is just the door panel, which you hang in an existing jamb using the old hinges and hardware. A pre-hung door comes already mounted in its own frame, ready to set into a rough opening. Which one you buy completely changes what you measure.
For a slab, you measure the existing door. For a pre-hung, you measure the rough opening in the framing plus the wall thickness. Confusing the two is the most common ordering mistake, so decide your path before you pull out the tape.
Measuring for a Slab Door
If you are replacing just the door and keeping the frame, measure the old door itself, not the opening. Record the width at the top, middle, and bottom, and the height on both edges, then use the largest consistent reading. Note the thickness and the hinge locations and swing direction.
Match the new slab to those dimensions and transfer the hinge and knob positions, or buy a pre-bored slab matching your hardware layout. Order the same size or slightly larger so you can trim to a precise fit, since you can shave a door down but you cannot add wood back.
Measuring the Rough Opening for Pre-Hung
For a pre-hung door, you measure the rough opening, which is the framed hole before the jamb goes in. The rough opening is typically the door width plus 2 inches and the door height plus about 2.5 inches, to leave room for the jamb and shimming. So a 30-inch door needs roughly a 32-inch-wide rough opening.
Measure the width between the framing studs and the height from the subfloor to the header. Also measure the wall thickness, since the door’s jamb must match it; standard 2×4 walls with half-inch drywall on each side give a 4-9/16-inch jamb.
Jamb Width Matters
Jamb width is the depth of the door frame, and it must match your wall’s total thickness. The two most common jamb widths are 4-9/16 inches for standard 2×4 walls and 6-9/16 inches for 2×6 walls, both assuming half-inch drywall. Measure your actual wall thickness from finished surface to finished surface.
Get this wrong and the jamb sits proud of the wall or recessed behind it, leaving you fussing with jamb extensions or trimming. A quick wall-thickness measurement before ordering saves that headache entirely.
Swing Clearances and Floor Gaps
A door needs breathing room to operate. Leave about 1/8 inch at the top and sides and a gap at the bottom sized for your flooring. Over hard flooring, a half-inch bottom gap is typical, but bump it up for thick carpet so the door clears the pile without dragging.
Check the swing path too. A door must clear light switches, other doors, and furniture through its full arc. If two doors would collide, consider changing a swing direction or switching to a pocket or barn door instead.
Handedness and Swing Direction
Doors have a handedness that you must specify when ordering pre-hung units. Stand facing the door from the side it swings toward you. If the hinges are on the left, it is a left-hand door; hinges on the right make it right-hand. Getting this backward means the door swings the wrong way and the hardware lands on the wrong side.
Sketch the room and mark which way you want the door to open before ordering. It is a small note that prevents a big return.
Non-Standard and Old-House Openings
Older homes frequently have openings that fall between standard sizes, or heights other than 80 inches. For a slightly off opening, a standard slab trimmed to fit usually works. For a significantly non-standard hole, you may need a custom door or to reframe the opening to a standard size, which is often cheaper than custom millwork.
Always measure twice and compare against the standard chart before ordering. Ten minutes with a tape measure is the cheapest insurance against a door that does not fit and cannot be returned.
Tools and Tips for Accurate Measuring
A quality tape measure and a level are all you truly need, but a few habits sharpen your numbers. Measure to the nearest sixteenth of an inch and always record width at three heights and height at both jambs, because old openings are rarely perfectly square. Note the out-of-square amount, since a badly racked opening may need reframing before a pre-hung will sit plumb. When ordering a slab, buy pre-bored for your hinge and bore layout if you can, which spares you from chiseling new hinge mortises by hand. Write every measurement down rather than trusting memory, and bring the sketch to the store so a salesperson can confirm your read before you commit to a door you cannot return.
How to Measure Door Size for a Replacement
To measure door size for a replacement, measure the existing door slab itself: width from edge to edge, height from top to bottom, and thickness. Most interior doors match a standard size such as 30 by 80 inches, so round your readings to the nearest standard and confirm with the jamb opening. If the door is missing or damaged, measure between the jambs and subtract the normal gaps.
Reading the Measurements
A door is named by its slab size, not by the hole. A slab that measures 29-3/4 or 30 inches wide is sold as a 30-inch door, written 2/6 in feet and inches. Many doors also carry the size stamped or penciled on the top edge or the hinge edge, which is worth checking before you reach for the tape.
| Width between jambs | Likely door width | Nominal size |
|---|---|---|
| About 24-1/4 inches | 24 inches | 2/0 |
| About 28-1/4 inches | 28 inches | 2/4 |
| About 30-1/4 inches | 30 inches | 2/6 |
| About 32-1/4 inches | 32 inches | 2/8 |
| About 36-1/4 inches | 36 inches | 3/0 |
The roughly 1/4-inch difference comes from the 1/8-inch gap left on each side. For height, measure from the underside of the head jamb to the floor; on a standard opening this is a little over 80 inches once the bottom gap for flooring is added.
Measuring a Door for Replacement Step by Step
- Measure the slab width at the top, middle and bottom, and the height on both edges.
- Measure thickness; interior doors are normally 1-3/8 inches.
- Measure hinge positions from the top of the door to the top of each hinge, plus the hinge height.
- Measure the knob bore from the door edge to the center of the hole, called the backset, usually 2-3/8 or 2-3/4 inches.
- Note which side the hinges are on and which way the door swings.
When the Numbers Do Not Match a Standard Size
If the slab is a fraction off, order the next standard size up and trim it. If the opening between jambs is out of square by more than about 1/4 inch from top to bottom, a new slab will not fix the rub or gap, and a pre-hung unit with a new jamb is the better route. Openings that are inches away from any standard size usually need a custom door or reframing.