Home Improvement

Laundry Closet Dimensions: Side-by-Side and Stacked Sizes

Laundry Closet Dimensions: Side-by-Side and Stacked Sizes

The most common laundry closet mistake is measuring for the machines and forgetting the hoses, the dryer vent and the door. Practical laundry closet dimensions for a full-size side-by-side pair start around 60 inches wide, 32 to 36 inches deep and 48 inches tall at the opening. A stacked full-size set needs only about 30 inches of width but 80 inches or more of height and roughly 34 to 36 inches of depth.

Those figures include the few inches behind the machines that the water valves, drain hose, power cord and dryer duct demand. Skip that space and the washer sticks out past the door frame, the vent crushes, or the bifold doors refuse to close. Compact 24-inch machines shrink the footprint further, making a closet as narrow as 27 to 30 inches workable.

Laundry Closet Dimensions at a Glance

Appliance sizes vary by model, so always check the installation guide for your specific washer and dryer. These ranges cover the vast majority of machines sold in the US and include working clearance.

Setup Width Depth Height
Full-size side-by-side (27 in. units) 56 to 62 in. 32 to 36 in. 42 to 48 in. min.
Full-size stacked (27 in. units) 30 to 32 in. 34 to 36 in. 80 to 84 in.
Compact side-by-side (24 in. units) 50 to 54 in. 27 to 30 in. 36 to 40 in.
Compact stacked (24 in. units) 27 to 30 in. 27 to 30 in. 72 to 76 in.
All-in-one washer/dryer combo 27 to 30 in. 28 to 32 in. 36 to 40 in.

If you plan to add a shelf, cabinet or folding counter over side-by-side machines, raise the height target. Top-loading washers need open space above the lid, often 20 inches or more beyond the cabinet height, so they rarely fit under a shelf.

Width: Side-by-Side vs Stacked

Full-size front-load washers and dryers are usually 27 inches wide. Side by side, that makes 54 inches of appliance. Add about 1 inch between the machines for vibration and airflow, plus 1 to 3 inches at each side wall so you can slide units in and out. That brings the practical minimum to 56 inches and a comfortable target to 60.

Stacking cuts the width in half. A stackable washer dryer pair with a stacking kit needs only the width of one machine plus an inch or two on each side, so a 30 to 32 inch closet works well. This makes stacking the go-to choice for hallway closets, apartments and second-floor conversions. Compact 24-inch units can squeeze into a 27-inch opening, though 28 to 30 inches makes installation far easier.

Door Frame Width vs Interior Width

Measure the finished door opening as well as the closet interior. A closet can be 60 inches wide inside but have a 48-inch opening framed by return walls. Machines must pass through the opening, and you need hand space to guide them. If the opening is narrower than the interior, check that each machine fits through diagonally and can still be rotated into place.

Depth: The Dimension Most People Underestimate

Front-load washers typically run 30 to 34 inches deep with the door closed, and the door adds several inches when open. Dryers are similar. Behind the machines you need room for the following:

  • Water supply hoses: 4 to 6 inches so the hoses can bend without kinking.
  • Dryer vent duct: 4 to 6 inches for a rigid or semi-rigid elbow. Periscope-style vent connectors can trim this to about 2 to 3 inches.
  • Power plug and outlet: enough room that the plug is not crushed against the wall.

Add those to a 32-inch machine and you need 36 to 38 inches from the back wall to the front of the door frame for the closet doors to close. Recessed washer outlet boxes and recessed dryer vent boxes, set into the wall between studs, can recover 3 to 4 inches. They are one of the best upgrades for a tight closet.

If depth is limited, look at shallower models. Some compact and stackable units are only 24 to 26 inches deep.

Height and Shelving Above the Machines

Side-by-side front-loaders stand about 38 to 40 inches tall. Pedestals add 12 to 15 inches. A shelf above them should sit at least 4 inches over the machine tops, so plan for 44 to 56 inches of clear height depending on pedestals.

Stacked units reach roughly 76 to 80 inches for full size. Leave a few inches above the dryer for airflow and to tip the top machine forward during service. A standard 80-inch closet door opening can be too short for a tall stack, so measure the header height before you buy. Dryer controls at the top of a stack can be hard for shorter adults to reach, which is worth considering for anyone in the household.

Door Types and How They Affect Closet Size

The closet door changes how much usable depth you have.

  • Bifold doors: the most common choice. Folded panels take up 4 to 6 inches inside the opening on each side, which can block a machine door or narrow the opening.
  • Sliding bypass doors: take little depth but only expose half the opening at a time, so side-by-side machines cannot both be open at once.
  • Pocket doors: disappear into the wall and leave the full opening clear. They require an empty wall cavity on one or both sides.
  • Swinging doors: need floor space outside the closet equal to the door width.
  • Louvered or vented doors: help the dryer pull in makeup air, which many manufacturers require for closet installs.

Check the dryer installation guide for minimum closet ventilation. Many require a set number of square inches of open vent area in the door, top and bottom, when the dryer sits in an enclosed space.

Looking to buy Laundry Closet Dimensions? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Utility Clearances: Water, Drain, Vent and Power

Utilities make or break a closet laundry, and they add inches to the laundry closet dimensions you planned around the machines alone. Plan for these before framing or buying machines.

  1. Water valves: mount the hot and cold shutoffs where you can reach them without pulling the washer out, usually 42 to 48 inches above the floor for side-by-side or to one side for stacked units. Quarter-turn valves close fast in an emergency.
  2. Drain: a standpipe of the size required by your local plumbing code, with a trap, typically set so its top is above the washer’s maximum water level.
  3. Dryer vent: run to the exterior with rigid or semi-rigid metal duct, as short and straight as possible. Never use plastic or foil accordion duct, and never vent into an attic or the closet itself.
  4. Electrical: washers use a standard 120-volt outlet, while electric dryers need a dedicated 240-volt circuit and outlet. Gas dryers need a gas line plus a 120-volt outlet.
  5. Floor protection: a drain pan under the washer, especially on upper floors, plus a water leak sensor.

Electrical Safety in a Laundry Closet

Before you plug in, move or work behind any machine, turn off the breaker and confirm power is off with a non-contact voltage tester. Plug the washer and dryer directly into their wall outlets, never into extension cords or power strips. Laundry area outlets generally require GFCI protection under current code, so confirm yours has it. Adding a new 240-volt dryer circuit or moving an outlet is a job for a licensed electrician, and never test or probe a live circuit yourself. If your dryer uses gas, the gas connection must be made and leak tested by a licensed professional. If you ever smell gas, leave the home and call the utility.

How to Measure Your Laundry Closet

Accurate laundry closet dimensions come from several measurements, not one.

  1. Measure interior width at the back, middle and front. Use the smallest number.
  2. Measure the finished door opening width and height.
  3. Measure depth from the back wall to the inside face of the door frame.
  4. Note the height and position of the valves, outlet, drain and vent.
  5. Check the hallway or route to the closet, since machines must travel through every turn.
  6. Compare those numbers to the installation guide for your chosen models, adding the clearances listed there.

Troubleshooting Tight Laundry Closets

  • Doors will not close: install recessed valve and vent boxes, use a low-profile vent connector, or switch to curtains or a pocket door.
  • Closet too narrow for side by side: stack the machines or choose 24-inch compact units.
  • No outside wall for venting: consider a ventless heat pump or condenser dryer, which needs only a drain or water tank.
  • Machines walk or vibrate: level the feet and leave an inch of space on each side so they do not knock the walls.
  • Dryer runs hot and slow: check for a crushed or long vent and add ventilation to the closet door.

Typical Costs for Laundry Closet Upgrades

Simple fixes are inexpensive. A recessed washer box or dryer vent box usually costs under a hundred dollars in parts. A new set of louvered bifold doors falls in the low hundreds. Bigger changes cost more: a new 240-volt dryer circuit typically runs a few hundred dollars, and relocating water lines and a drain to create a new closet laundry can reach the low thousands. Building a closet from scratch with framing, plumbing, electrical and venting often runs several thousand dollars depending on distance to existing lines.

When to Call a Licensed Professional

If your laundry closet dimensions require moving plumbing or wiring, bring in the right trades. Hire a licensed plumber for new supply lines or drains, a licensed electrician for any new circuit or outlet, and a licensed gas fitter for gas dryer hookups. Many areas require permits for these changes. A contractor can also reframe a closet opening, add a pocket door or route a dryer vent through an exterior wall correctly.

Frequently Asked Questions

How wide does a laundry closet need to be for a side-by-side washer and dryer?

Plan on at least 56 inches for two 27-inch machines, with 60 inches being more comfortable. That leaves space between units and at the side walls for installation and airflow.

How deep should a laundry closet be?

Most full-size setups need 32 to 36 inches of depth, measured from the back wall to the door frame. That covers the machine depth plus room for hoses, the vent duct and the plug.

What size closet do I need for a stacked washer and dryer?

A full-size stacked pair fits in a closet roughly 30 to 32 inches wide, 34 to 36 inches deep and at least 80 inches tall. Compact stacks need about 27 to 30 inches of width.

Do laundry closet doors need vents?

Many dryer manufacturers require ventilation openings when the dryer is enclosed in a closet. Louvered doors or vent grilles at the top and bottom usually satisfy that requirement.

Can I put a washer and dryer in a closet without an outside wall?

Yes, if you choose a ventless dryer such as a heat pump or condenser model. You still need a water supply, a drain and the correct electrical outlet for each machine.

What are laundry closet dimensions in cm?

A full-size side-by-side laundry closet needs about 152 cm (60 inches) of width and 81 to 91 cm (32 to 36 inches) of depth. A full-size stacked pair fits in about 76 to 81 cm (30 to 32 inches) of width, 86 to 91 cm of depth and at least 203 cm (80 inches) of height. Always confirm against the installation guide for your machines.

How much space do you need in front of a laundry closet?

Plan roughly 36 to 42 inches of clear floor in front of the closet so you can open a front-load door fully, kneel to load, and pull a machine out for service. Front-load doors swing out about the width of the machine, so a hallway narrower than that makes loading awkward. Swinging closet doors need extra space on top of that.

How wide should a laundry closet door opening be?

For side-by-side machines, the opening should ideally span most of the closet width, often 60 inches with a pair of bifold or pocket doors, so both machine doors open and both units can be pulled out. For a stacked pair, an opening of about 30 to 32 inches works. Every opening must be wider than the machines with room for your hands to guide them in.