Home Improvement

Recessed Puck Lights: Hardwired 12V Install in Cabinets

Recessed Puck Lights: Hardwired 12V Install in Cabinets

Surface-mounted pucks stick down below the cabinet and catch the eye, while flush-mounted ones disappear into the wood and throw clean pools of light onto the counter. Recessed puck lights give that built-in look, but they require cutting holes, routing wires and placing a driver somewhere it can breathe. Plan the layout and the power source before you touch a hole saw and the job is straightforward for a careful DIYer.

The short answer: choose low-voltage 12V LED pucks for most cabinet work, drill holes with the hole-saw size listed on the fixture spec sheet, run the leads to a UL-listed driver sized with headroom for the total wattage, and connect the pucks in a daisy chain or a hub as the manufacturer specifies. Feed the driver from a switched outlet or a hardwired junction box with the breaker off. Any new circuit or hardwired connection you are not comfortable with belongs to a licensed electrician.

The sections below cover choosing between 12V and 120V pucks, sizing holes, placing the driver, wiring, upgrading old halogen units and fixing common problems.

Choosing Recessed Puck Lights: 12V vs 120V

12V puck lights run through a driver or transformer that steps household current down to low voltage. The wiring from the driver to each puck is thin and safer to route through cabinets, and most kitchen under-cabinet systems use this format. 12 volt puck lights also come in dimmable, color-temperature adjustable and RGB versions.

120V puck lights connect directly to line voltage with no separate driver. They simplify the parts list, but every connection is now high voltage, so the wiring must meet local code, stay inside approved boxes or fixtures, and usually be installed by an electrician. For most homeowners, 12V LED pucks are the practical choice.

Other Selection Factors

  • Brightness and color: Many LED puck lights produce roughly 150 to 300 lumens each. A warm white around 2700K to 3000K suits most kitchens.
  • Finish: White, silver, bronze and black puck lights let you match cabinet hardware or disappear against dark wood.
  • Depth: Check the housing depth against your cabinet bottom thickness. Many recessed units need about 3/4 inch or more.
  • Location: Cabinet puck lights, in-shelf display lights and puck lights for ceiling soffits all use similar hardware but may carry different ratings, so confirm the fixture is rated for the location.

Tools and Materials

  • 12v recessed led puck lights with trims and leads
  • UL-listed LED driver or transformer, plus a compatible dimmer if needed
  • Hole saw matched to the fixture’s cutout size, and a drill
  • Low-voltage extension cables and connectors or a distribution hub
  • Cable clips or staples rated for low-voltage wire
  • Non-contact voltage tester, wire strippers and wire connectors
  • Tape measure, pencil, square and safety glasses

Step-by-Step Installation

  1. Plan spacing. Place pucks about 16 to 24 inches apart and 3 to 6 inches from the front edge of the cabinet so light lands on the work surface instead of the backsplash. Mark centers on the underside.
  2. Check what is above. Make sure there are no shelves, pipes or wires directly above each hole and that the cabinet bottom is thick enough for the housing.
  3. Drill the holes. Use the exact hole-saw diameter the manufacturer lists, often somewhere around 2 to 3 inches. Drill from below until the pilot bit breaks through, then finish from inside the cabinet to prevent tear-out.
  4. Plan the driver location. Mount the driver inside an upper cabinet, above the cabinet in the soffit area, or in another accessible and ventilated location. Keep it away from insulation, heat and moisture, and never bury it inside a closed wall.
  5. Size the driver. Add up the wattage of every puck and choose a driver rated comfortably above that load. Leaving about 20 percent headroom keeps it running cool.
  6. Route the wires. Run low-voltage leads from each puck to the driver, either by daisy-chaining from one puck to the next or by running each to a central hub. Follow the manufacturer’s limit on how many pucks can be chained and on total wire length.
  7. Turn off the power. If the driver will be hardwired, turn off the breaker for the circuit and confirm power is off at the wires with a non-contact voltage tester before touching anything.
  8. Connect the driver. Plug-in drivers go to a nearby outlet. Hardwired drivers connect inside an approved junction box with proper connectors and grounding.
  9. Seat the pucks. Press each housing into its hole until the spring clips or flange hold it flush.
  10. Restore power and test. Turn the breaker back on or plug in the driver, then check every light and any dimmer.

Fire and Heat Safety

Heat is the main hazard with recessed fixtures. Older halogen puck lights and xenon units run very hot and have been linked to scorched cabinets and melted contents. LEDs run far cooler, but they still need airflow. Maintain the clearance listed on the fixture instructions, keep paper, towels and plastic items away from the housing, and never cover a driver with insulation or stored goods. Use only UL-listed drivers and fixtures sized for the load.

Never test or work on live 120V wiring. If a new circuit, a new switch location or a hardwired connection is needed and you are unsure how to do it, hire a licensed electrician. Many areas require a permit for new wiring.

Swapping Halogen or Xenon Pucks for LED

Replacing hot halogen puck lights is one of the best upgrades you can make. Match the new LED puck to the existing hole size so you do not need to recut, or use a trim ring to cover a larger opening. Replace the old magnetic or electronic transformer with an LED driver, because many halogen transformers do not work reliably with low LED loads and cause flicker. Check dimmer compatibility too.

Looking to buy Recessed Puck Lights? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Layout Ideas Beyond the Kitchen Counter

Recessed puck lights are not just for under upper cabinets. Inside glass-front display cabinets, a single puck per shelf section highlights dishes or collectibles, though glass shelves let light pass through to the level below. In bookcases, a flush mount puck in the top rail of each bay adds a warm wash without visible fixtures. Closets, pantries and bar areas also benefit from small pucks tied to a door switch or a motion sensor on the low-voltage side.

For ceilings and soffits, choose fixtures specifically rated for that installation, and remember that insulation contact ratings matter when a fixture sits in a ceiling cavity. Wet or damp locations, such as a shower niche or an outdoor soffit, require fixtures labeled for those conditions.

Color options have widened too. RGB puck lights and tunable-white versions work with compatible controllers, letting you shift from bright task light to a softer evening glow. Stick with one product family so the color temperature matches across every fixture in view.

Troubleshooting

Lights flicker. Usually an incompatible dimmer, an old halogen transformer or a loose connector. Swap in an LED-rated driver and dimmer and reseat connections.

Last puck is dimmer. Voltage drop from long runs or too many chained pucks. Shorten runs, use a hub or add a second driver.

Nothing lights. Check the outlet or breaker, confirm polarity on low-voltage connectors and verify that the driver is receiving power.

Driver feels hot. It is undersized or enclosed. Move it to a ventilated spot or upgrade to a larger rating.

General Cost Ranges

A basic kit of hardwired puck lights with a plug-in driver is affordable, and higher-end dimmable or RGB puck lights cost more per fixture. Budget extra for a hole saw, connectors and a dimmer. Hiring an electrician to install a hardwired driver, a new switch or a new circuit adds labor that varies widely by region and complexity.

When to Call a Licensed Electrician

Call a pro for 120V puck lights, new circuits, new switch boxes, work inside the electrical panel or anything that requires a permit. An electrician can also confirm that your existing circuit can handle the added load and that all connections sit inside approved enclosures.

Frequently Asked Questions

Are 12V puck lights better than 120V?

For most cabinet installs, yes. Low-voltage wiring is easier and safer to route, while 120V pucks require line-voltage connections that often need an electrician.

What size hole saw do I need for recessed puck lights?

Use the cutout size printed on the fixture spec sheet. It varies by brand and model, so measure before drilling.

How many puck lights can I daisy-chain?

Follow the manufacturer’s stated limit and keep total wattage under the driver rating with some headroom. Exceeding either causes dimming or overheating.

Can I replace halogen puck lights with LED?

Yes. Match the hole size, replace the old transformer with an LED driver and confirm dimmer compatibility.

Do recessed puck lights get hot?

LED pucks run much cooler than halogen, but they still need the clearance listed by the manufacturer and should never be covered.