Ordering a linear drain one size too short is a mistake you see every time you step into the shower. The gap between the end of the grate and the wall looks unfinished, and it can change how the floor has to slope. Getting schluter linear drain sizes right comes down to three choices: channel length, outlet position, and a grate assembly that matches your tile thickness.
The quick answer: Schluter’s standard KERDI-LINE channel comes in lengths from 20 to 72 inches in 4 inch steps, with a center outlet or an offset outlet located 8 inches from the end of the channel. Every version connects to a standard 2 inch no-hub drain line, and a bonding flange extends about 1 inch beyond the channel on all sides to tie into the waterproofing membrane. If no fixed length fits your opening, KERDI-LINE-VARIO is a cut-to-length version sold in 48 and 96 inch stock lengths.
The specs here come from Schluter’s US product pages at the time of writing. Grate part numbers, offset availability for each length, and actual grate measurements are listed in Schluter’s product table, so confirm there before ordering.
Schluter Linear Drain Sizes at a Glance
This table summarizes the published specs for the standard KERDI-LINE and the cut-to-length VARIO model.
| Spec | KERDI-LINE (fixed length) | KERDI-LINE-VARIO (cut to length) | What It Means |
|---|---|---|---|
| Channel lengths | 20 to 72 in (50 to 180 cm), 4 in steps | 48 in or 96 in stock, trimmed on site | Fixed sizes vs custom fit |
| Minimum length | 20 in | 10 in minimum cut | VARIO suits odd or narrow openings |
| Outlet | 2 in no-hub | 2 in, PVC and ABS couplings included | Standard residential shower drain size |
| Outlet position | Center or offset (8 in from channel end) | Anywhere along the trimmed length | Offset helps avoid floor joists |
| Channel width | See product table | 1-11/16 in (43 mm) | Narrow profile at the floor |
| Bonding flange | About 1 in past channel on all sides | Polypropylene flange with KERDI collar | Ties drain into the membrane |
| Grate tile range | 1/8 to 1 in on standard frames | Minimum tile thickness 3/8 in suggested | Match frame to tile thickness |
| Joining drains | KERDI-LINE-FC connects channels end to end | Not applicable | For very wide showers |
Standard lengths therefore run 20, 24, 28, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, and 72 inches. Grate assemblies are sold separately from the channel body, and grate lengths are matched to each channel.
How to Size a Linear Drain by Shower Width
Placement affects which of the Schluter linear drain sizes makes sense. Linear drains are usually placed in one of two positions: against a wall, typically the back wall, or across the shower entry. Schluter also allows placement at an intermediate point in the floor. In each case, the drain runs across the width of the shower, perpendicular to the direction the floor slopes.
Wall-to-wall placement
For a clean wall-to-wall look, choose the longest standard length that fits between the finished wall surfaces, accounting for the wall board, membrane, thin-set, and tile on each side. With 4 inch increments, a fixed channel often leaves a small gap on each end. That gap is normally tiled, and the floor plane on either end of the drain needs to be sloped to flow toward the grate. If you want the drain to run fully from wall to wall, the VARIO model is designed for that: it is trimmed to the measured length, and Schluter calls for a small gap of 1/16 to 1/8 inch at each wall.
Shorter, centered placement
A drain doesn’t have to span the full width. A shorter channel centered on the wall or entry still works, but the tile around each end must be sloped to the grate, which means more cuts. Many installers prefer a drain that covers most of the width to keep the floor a single flat plane.
Quick sizing examples
- 36 inch wide shower: a 32 inch fixed channel is a common choice, or a VARIO trimmed to the full width.
- 48 inch wide shower: a 44 inch channel generally fits once wall layers are accounted for; a 48 inch channel requires a framed opening wider than 48 inches after finishes.
- 60 inch wide shower or tub replacement: a 56 inch channel often fits within finished walls.
- Over 72 inches: join two channels with KERDI-LINE-FC, or use a VARIO.
These are planning examples, not rules. Measure the finished width (after board and membrane) and check the actual overall channel length, including the flange, in Schluter’s product table before ordering.
Outlet Position: Center vs Offset
The center outlet sits in the middle of the channel, which matches most new construction. The offset outlet sits 8 inches from one end of the channel. Schluter notes that offset versions are useful when obstacles such as floor joists sit under the center of the drain. Offset outlets are not available in every length, so confirm availability for your chosen size. On a VARIO, the outlet can go anywhere along the trimmed channel; when placed against a wall, Schluter specifies the outlet at 1-3/4 inches on center from the face of the wall board.
Grate Designs and Frame Heights
KERDI-LINE grates come in seven designs. Choosing the right frame for your tile thickness keeps the grate flush with the surrounding tile.
- SOLID and SQUARE grates: standard frame adjustable for tile from 1/8 to 1 inch thick, with a 3/8 inch reveal. Available in brushed, chrome, or textured color-coated finishes. A locking version of the SQUARE grate is offered in brushed stainless with a 3/4 inch frame.
- TILE grate (frameless): sits flush with the top of the channel and accepts any tile thickness, so the tile itself becomes the grate surface.
- TILE grate with thin frame: three frame heights. The 1/4 inch frame suits coverings about 13/64 to 9/32 inch thick, the 1/2 inch frame suits 9/32 to 15/32 inch, and the 7/8 inch frame suits 5/8 to 25/32 inch.
- STYLE grates (FLORAL, CURVE, PURE): frame adjustable from 1/4 to 23/32 inch with a minimal reveal, brushed finish only.
The VARIO line uses its own set of grates, listed by Schluter in Square, Floral, Herringbone, and Slant patterns in brushed stainless or textured color finishes.
Nominal grate length and measured grate length are not the same thing. Grates generally measure a little shorter than the nominal channel size, so check the product table if you are laying out tile cuts to the fraction of an inch.
Flow and Shower Head Count
Schluter states the VARIO is designed for a single standard shower head at up to 2.5 gallons per minute, consistent with plumbing code. The standard KERDI-LINE product page does not publish a flow figure. If you plan multiple heads, body sprays, or a rain panel, ask Schluter’s technical support or your plumber to confirm drain capacity before you commit to a size and outlet configuration.
Installation Overview
- Plan the drain line with your plumber so the 2 inch outlet lands where the channel outlet will be.
- Set the channel height using the foam channel support or a sloped mortar bed so the grate ends up flush with the finished tile.
- Bond the flange with a Schluter setting mortar or unmodified thin-set, using the notched trowel specified in the instructions.
- Integrate the waterproofing by bonding the KERDI collar to the floor membrane and running it up adjacent walls as needed.
- Slope the floor to the drain with a pre-sloped linear tray or mortar bed.
- Tile and set the grate, adjusting the frame height to your tile.
Large-format tile pairs well with linear drains because the floor slopes in a single plane. A tile leveling system keeps those big tiles flat across the slope.
Cost Ranges
In general terms, a linear drain channel and grate together cost noticeably more than a standard center drain kit, with longer lengths and designer grates at the higher end. Installed by a pro, expect added labor for plumbing, the sloped bed or tray, and careful tile layout. Prices vary widely by region and finish, so get local quotes.
Troubleshooting
- Grate sits higher or lower than the tile: Readjust the frame height or switch to a frame sized for your tile thickness.
- Water pools at the drain ends: The floor plane at the ends is not sloped to the grate. This is common with shorter drains.
- Outlet lands on a joist: Consider the offset outlet version or a VARIO with the outlet repositioned.
- Grate rattles: Check that the frame is fully seated and that no debris is in the channel.
When to Call a Pro
Linear drains are less forgiving than center drains because the slope, height, and waterproofing must line up precisely. Plumbing changes to move or add a drain line should go to a licensed plumber, and many areas require a permit for shower drain work. Hire a tile contractor experienced with bonded waterproofing if you want the manufacturer’s system warranty, which depends on following the installation handbook.
Frequently Asked Questions
What lengths does Schluter KERDI-LINE come in?
Fixed channels run from 20 to 72 inches in 4 inch increments. The VARIO version comes in 48 and 96 inch lengths that are cut to fit.
What are the Schluter linear drain dimensions for the outlet?
KERDI-LINE uses a standard 2 inch no-hub outlet. The offset version places the outlet 8 inches from one end of the channel.
Can I cut a Schluter linear drain to length?
The standard KERDI-LINE is sold in fixed lengths. KERDI-LINE-VARIO is designed to be trimmed on site, down to a minimum of 10 inches.
What tile thickness works with KERDI-LINE grates?
Standard frames adjust for tile from 1/8 to 1 inch thick. The frameless TILE grate accepts any tile thickness.
How wide is the Schluter VARIO channel?
Schluter lists the VARIO channel at 1-11/16 inches wide. Check the product table for the standard KERDI-LINE channel width.
Prefer to explore on your own?
See how new flooring looks in your actual room in seconds — free, no signup.
Try the free Floor Studio →