A prefab shower bench saves hours of framing, but only if it actually fits the space you planned. Many remodelers order a bench after the tray is set and then discover the seat sticks out farther than expected or the curb length leaves a gap. Knowing the schluter shower bench dimensions before you buy, along with the matching curb and tray sizes, lets you lay out the whole shower on paper first.
Part of our Bathroom Remodeling & Flooring guide — explore the full guide →
Here is the short answer. Schluter’s KERDI-BOARD-SB prefabricated bench comes in four sizes, all 20 inches tall: two triangular corner benches (16 by 16 inches and 24 by 24 inches) and two rectangular benches (38 by 11-1/2 inches and 48 by 16 inches). The companion KERDI-BOARD-SC curb comes in 38, 48, and 60 inch lengths, each 6 inches by 4-1/2 inches in cross section. Both are made from KERDI-BOARD, a waterproof foam building panel, and are designed to sit beside Schluter’s KERDI-SHOWER trays.
- Schluter Shower Bench Dimensions and Curb Sizes
- What Each Bench Size Feels Like in Use
- Bench Height vs Code and Comfort
- Curb Height and Plumbing Code
- Pairing Benches and Curbs with Schluter Trays
- Installation Overview
- Cost Ranges
- Troubleshooting Fit Problems
- When to Call a Pro
- Frequently Asked Questions
All figures here come from Schluter’s US product pages at the time of writing. Product lines get updated, so confirm the current product table before ordering.
Schluter Shower Bench Dimensions and Curb Sizes
The table lists each published size in inches with the metric equivalent Schluter gives. Bench sizes are listed as width by depth by height. The manufacturer page lists curb sizes without labeling each axis; the 4-1/2 inch figure is widely treated as the height and 6 inches as the width, but check the product sheet for your SKU.
| Product | Shape | Size (inches) | Size (cm) | Typical Use |
|---|---|---|---|---|
| KERDI-BOARD-SB | Triangular | 16 x 16 x 20 | 41 x 41 x 51 | Small corner seat or foot rest in compact showers |
| KERDI-BOARD-SB | Triangular | 24 x 24 x 20 | 61 x 61 x 51 | Comfortable corner seat in larger showers |
| KERDI-BOARD-SB | Rectangular | 38 x 11-1/2 x 20 | 97 x 29 x 51 | Narrow ledge-style bench along a short wall |
| KERDI-BOARD-SB | Rectangular | 48 x 16 x 20 | 122 x 41 x 51 | Full-width seat along a back or end wall |
| KERDI-BOARD-SC | Curb | 38 x 6 x 4-1/2 | 97 x 15 x 11.5 | Entry for 38 inch wide trays |
| KERDI-BOARD-SC | Curb | 48 x 6 x 4-1/2 | 122 x 15 x 11.5 | Entry for 48 inch wide trays |
| KERDI-BOARD-SC | Curb | 60 x 6 x 4-1/2 | 152 x 15 x 11.5 | Entry for 60 inch wide trays and tub replacements |
A note on names: some shoppers search for a “KERDI-SHOWER-SC” curb. Schluter currently lists the curb under the KERDI-BOARD-SC name, grouped with its KERDI-BOARD panels.
What Each Bench Size Feels Like in Use
16 x 16 inch triangular
The smallest corner bench offers a shallow seat. Measured from the corner, the front edge sits 16 inches out along each wall, which leaves a usable seat depth well under that because of the triangular shape. It works as a perch, a place to rest a foot while shaving legs, or a shelf for bottles. In a 36 or 38 inch wide shower, it is often the only bench that leaves enough standing room.
24 x 24 inch triangular
The larger corner model gives a real seat for most adults. It suits showers 48 inches or wider in both directions, where giving up a corner does not crowd the shower head zone.
38 x 11-1/2 inch rectangular
At 11-1/2 inches deep, this bench reads more as a long ledge. It fits along the short end of a 38 inch wide alcove shower, such as a converted tub space, without stealing much floor area.
48 x 16 inch rectangular
Sixteen inches of depth is a comfortable seat. This model spans the end wall of a 48 inch wide shower, or sits along the back wall of a longer enclosure.
Bench Height vs Code and Comfort
Height is the one figure shared across all Schluter shower bench dimensions: every KERDI-BOARD-SB bench has a published height of 20 inches. Add thin-set and tile, and the finished seat usually lands somewhere around 20-1/2 to 21 inches above the tray, depending on the tile thickness. Keep in mind that the tray itself sits slightly above the bathroom floor.
Most residential building codes do not require a shower bench or set a mandatory height. Accessibility guidelines for accessible showers call for a seat height of 17 to 19 inches above the shower floor, so a finished KERDI-BOARD-SB bench sits above that range. If you are designing for aging in place or an accessible bathroom, talk with your designer or contractor about a site-built bench at the lower height, or confirm with Schluter’s technical support whether trimming the bottom is acceptable for your installation. Schluter’s FAQ addresses trimming the bench to width with a utility knife; it does not publish a height reduction method on the product page.
Also check depth. A seat shallower than about 15 inches is a perch rather than a chair, so if seating is the main purpose, choose the 24 inch triangle or the 48 by 16 inch rectangle.
Curb Height and Plumbing Code
The 4-1/2 inch KERDI-BOARD-SC curb is a common residential height. Model plumbing codes generally require a shower dam to stand a set distance above the drain to hold water in the receptor, typically a range of roughly 2 to 9 inches, measured from the top of the dam to the top of the drain. Local codes vary, so confirm with your building department before you build.
Schluter says the curb can be cut to length with a utility knife or handsaw, and that height can be reduced by removing material from the bottom. Multiple curbs can be joined end to end for larger openings. The manufacturer also states the curbs will support a glass door or glass block wall, which matters for frameless glass installs.
Pairing Benches and Curbs with Schluter Trays
Schluter describes both the bench and the curb as typically installed adjacent to a prefabricated KERDI-SHOWER tray. Matching sizes avoids awkward cuts and makes the waterproofing connections straightforward.
- KERDI-SHOWER-T (center drain): 38 x 60, 48 x 60, 48 x 72, 60 x 60, and 72 x 72 inches. A 38 or 48 inch curb fits the short side; a 60 inch curb fits the long side of a 60 inch tray.
- KERDI-SHOWER-TS (offset drain): 38 x 60 inches, aimed at bathtub replacements. Pair it with the 60 inch curb along the open side and the 38 inch rectangular bench at one end.
- KERDI-SHOWER-TT (thin perimeter): 32 x 38, 36 x 36, 38 x 38, 36 x 48, and 48 x 48 inches, plus a 38 x 38 neo-angle version. These smaller trays suit the 16 inch triangular bench.
- KERDI-SHOWER-LT/-LTS (linear drain trays): sizes listed separately on Schluter’s linear tray page, so confirm the current size table before ordering. A 48 x 16 rectangular bench works at the end of a 48 inch wide tray.
Remember that a bench placed on top of the tray takes up floor area, while a bench outside the tray footprint (built over the wall framing area or a separate floor section) does not. Sketch the layout at full scale with painter’s tape on the floor to check elbow room.
Installation Overview
Schluter’s published instructions follow a consistent pattern for both the bench and curb.
- Dry fit the bench or curb in position and mark its outline. Trim to width or length as needed.
- Apply bonding mortar. Schluter lists its own setting mortars or an unmodified thin-set, applied with a 1/4 by 3/8 inch notched trowel to the substrate, walls, and tray edge.
- Press firmly into place and check the underside and back for full mortar coverage and support.
- Confirm the slope. The bench top is sloped to shed water; the slope must point toward the shower floor.
- Waterproof the seams. Cover all joints with KERDI-BAND and the supplied preformed corners, overlapping at least 2 inches, and press out air pockets.
- Tile after the mortar and seams are ready, following the setting material’s cure guidance.
The triangular benches ship with preformed 135 degree inside corners plus left and right bench corners, while the rectangular benches include 90 degree inside and outside corners. Large-format tile on the bench top looks clean with fewer grout joints; a tile leveling system helps keep those big tiles flat and aligned with the wall tile.
Cost Ranges
Prefab foam benches and curbs generally cost more than the raw materials for a framed bench, but they save labor and waterproofing time. In general terms, expect a prefab bench or curb to fall in the low to mid hundreds of dollars depending on size, with waterproofing band and corners adding a modest amount. Installed by a tile pro, a bench typically adds a few hundred dollars or more in labor for setting, waterproofing, and tiling. Check current pricing locally.
Troubleshooting Fit Problems
- Walls out of square: Trim the bench to width and fill small gaps with mortar before banding the seam.
- Bench rocks on the tray: Full mortar coverage is required. Pull it, re-trowel, and reset.
- Water pools on the seat: The bench was installed with the slope reversed or the tile was set flat. Confirm the slope points toward the drain area.
- Curb too long for the opening: Cut it to length; both ends must be banded to the walls.
When to Call a Pro
A shower is only as good as its waterproofing. If you are new to bonded membranes, have a tile contractor familiar with Schluter’s system handle the installation, especially when you want the manufacturer’s warranty, which depends on following its installation handbook. Any drain relocation or new plumbing belongs with a licensed plumber, and permits may be required for shower remodels in your area.
Frequently Asked Questions
How tall is the Schluter shower bench?
All four KERDI-BOARD-SB sizes have a published height of 20 inches before tile. Thin-set and tile add a bit more.
What is the Schluter bench size for a corner?
Corner benches come in 16 x 16 inch and 24 x 24 inch triangular versions, both 20 inches tall.
What are the Schluter curb dimensions?
The KERDI-BOARD-SC curb comes in 38, 48, and 60 inch lengths, each listed as 6 inches by 4-1/2 inches in cross section.
Can a Schluter shower bench be cut to size?
Schluter says the bench can be trimmed to width with a utility knife. Check with the manufacturer before altering its height.
Can I use a Schluter bench with a mortar bed instead of a tray?
Schluter shows benches beside its trays, and its curbs work with trays or mortar bases. Confirm bench details with the installation handbook for your setup.
Prefer to explore on your own?
See how new flooring looks in your actual room in seconds — free, no signup.
Try the free Floor Studio →