A custom-built screened porch from a general contractor can easily run $25,000 or more, which is why so many homeowners start shopping for a kit instead. Screened in porch kits range from simple screen-panel systems that enclose an existing covered patio in a weekend to complete framed packages with roof, posts, and doors. Picking the wrong type is expensive, though, because the right kit depends almost entirely on what you already have: a roof, a deck, a slab, or nothing at all. This guide breaks down each category, the real costs, and the planning details that make an install succeed.
Types of Screened in Porch Kits
The phrase screened in porch kits covers several very different products. Knowing which group you are in narrows your choices fast.
Screen Panel Systems for Existing Covered Porches
If you already have a roof supported by posts, you only need to fill the openings. Screen panel systems use aluminum or vinyl frames, or a channel-and-spline system that attaches directly to your posts, beams, and rails. Channel systems use a base strip fastened to the framing, the screen stretched over it, and a snap-on cap that locks the mesh and covers the fasteners. The result looks clean and makes it easy to replace torn screen later.
Aluminum Patio Enclosure Kits
These include aluminum posts, headers, kick plates, and screen frames sized to your opening. Some are freestanding with their own insulated or aluminum roof panels, while others attach under an existing overhang or to a house wall with a ledger. They are low maintenance and common in the Southeast and Southwest.
Complete Framed Porch Kits
Wood or vinyl-clad kits provide pre-cut posts, beams, rafters, roofing panels or sheathing, and screen systems. They are essentially a small addition in a box and usually need a deck or slab underneath. Expect a multi-weekend project and a building permit.
Retractable Screen Kits
Retractable screens roll up into a housing at the top of each opening, manually or with a motor. They suit homeowners who want an open porch most of the time and screened protection on buggy evenings. They cost more per opening and require precise, square openings.
What Screened in Porch Kits Cost in 2026
| Kit Type | Typical Kit Price | Pro Install Adds |
|---|---|---|
| Channel screen system (existing porch) | $3-$8 per sq ft of opening | $4-$10 per sq ft |
| Framed aluminum/vinyl screen panels | $8-$20 per sq ft of opening | $5-$12 per sq ft |
| Aluminum patio enclosure with roof | $6,000-$18,000 | $3,000-$8,000 |
| Complete wood porch kit with roof | $8,000-$25,000 | $6,000-$20,000 |
| Retractable screens | $500-$2,500 per opening | $150-$500 per opening |
To put that in perspective, enclosing an existing 12×14 covered porch with three open sides might mean about 340 square feet of screen area. A quality channel system would cost roughly $1,000 to $2,700 in materials, plus a screen door at $200 to $800. By contrast, building a new 12×14 porch from scratch with a roof and screening often totals $15,000 to $40,000 when hired out, depending on region and finishes.
Choosing Screen Mesh
The mesh matters more than most buyers expect. It affects visibility, airflow, durability, and bug protection.
- Standard fiberglass (18×16 weave): inexpensive, easy to install, and blocks mosquitoes and flies. The default choice.
- Fine or no-see-um mesh (20×20 or finer): keeps out biting midges common near the coast and wetlands. It slightly reduces airflow.
- Pet-resistant mesh: vinyl-coated polyester several times stronger than fiberglass. Use it at least on the lower half of the walls if you have dogs or cats.
- Solar or shade mesh: blocks a large share of solar heat and glare, useful on west-facing porches in hot climates, but it darkens the view.
- Aluminum mesh: crisp look and good durability, though it can dent and may corrode near salt water.
A charcoal-colored mesh is easier to see through than silver or gray because it reflects less light. Most homeowners are surprised how much it improves the view.
Planning Before You Order
Measure Every Opening Separately
Porch posts are rarely perfectly plumb, and openings built years apart can differ by an inch or more. Measure the width at top, middle, and bottom, and the height at both sides. Order to the smallest measurement for framed panels, or plan to shim. Channel systems are more forgiving because they are cut to fit on site.
Add Mid-Rails and Kick Plates
Screen spans taller than about 7 feet or wider than about 5 feet tend to billow in wind. Plan a horizontal mid-rail at roughly 30 to 36 inches, which doubles as protection against chairs and pets. A solid kick plate of aluminum, composite, or wood along the bottom 12 to 24 inches keeps the screen from tearing at floor level.
Plan the Door
Screen doors see the most wear. A standard 36-inch-wide door works for most porches, but consider a 42-inch or double door if you will carry furniture or grills through it. Choose a door with a closer and a sturdy latch, and make sure the swing clears furniture and steps.
Seal the Floor Gaps
Insects exploit gaps between deck boards. If your porch floor is a deck with 1/8- to 1/4-inch board gaps, staple screen material underneath the joists or over the joists before new decking, or install a solid floor. On concrete, seal gaps at the base of the screen framing with exterior sealant.
Permits and Structural Considerations
Screening an existing covered porch usually does not require a permit, though some towns and HOAs still want to review it. Adding a roof, new posts, or a ledger attached to the house almost always does. Roof structures must be designed for your local snow and wind loads, which can range from 20 psf in mild climates to 50 psf or more in snowy regions. Reputable kit manufacturers publish engineering data or stamped drawings for your area; ask for them before buying.
The ledger connection is where many DIY porches fail. A roof or deck ledger attached to the house must be fastened into the rim joist with properly sized structural screws or through-bolts on a specified pattern, never only nails, and it must be flashed so water cannot get behind the siding. Posts need footings sized for the load and extending below the frost line in cold climates. If your existing deck was not designed to carry roof loads, adding a roof on top of it can overload the framing.
DIY Installation Overview for a Channel System
- Prep the framing. Replace rotted wood and paint or stain the framing now, since it is much harder after screening.
- Install mid-rails and kick plates so every opening is a manageable size.
- Fasten the base channel around each opening with stainless or coated screws, keeping it straight with a level.
- Stretch the screen. Starting at the top, press the screen into the channel with a spline roller, working down the sides and then the bottom, keeping the mesh taut but not distorted.
- Trim excess mesh with a sharp utility knife.
- Snap on the cap strips to lock the screen and create a finished look.
- Hang the door last, shimming the jamb as needed so it closes smoothly.
Two people can typically screen a 12×14 porch with a channel system in one to two days. A complete framed porch kit with a roof generally takes several weekends for experienced DIYers.
Adding Fans, Lights, and Outlets
Ceiling fans move air on still evenings and discourage mosquitoes, which are weak fliers. Choose a fan rated for damp or wet locations, and use outdoor-rated, GFCI-protected receptacles. Plan wiring before screening so you are not fishing cable through finished trim. Electrical work on a porch should be done by a licensed electrician in most jurisdictions, and it will usually require its own permit and inspection.
When to Hire a Professional
A screen-only kit on a sound existing porch is a very approachable DIY job. Call a licensed contractor when you need to add a roof, attach a ledger to your home, build new footings, or modify an existing deck to carry more load. If the porch is elevated more than a few feet off the ground, guard rail heights (typically 36 inches minimum under the IRC for decks over 30 inches above grade) and stair requirements also come into play. A contractor can confirm your framing and pull the right permits so the finished porch passes inspection and adds value when you sell.
Match the kit to what you already have, choose mesh for your climate and pets, and put your effort into careful measuring. The right screened in porch kits deliver most of the comfort of a custom build at a fraction of the price.
Screened in Porch Kits FAQs
Can I screen in a porch myself?
Yes, if the porch already has a roof and solid framing. Channel screen systems and framed screen panels are designed for DIY installation with basic tools. Adding a roof or new posts is a larger project that usually needs a permit and possibly a contractor.
How much does it cost to screen in a porch?
Screening an existing covered porch with a DIY kit usually costs $3 to $20 per square foot of opening, or roughly $1,000 to $5,000 for a typical porch. Building a new screened porch with a roof generally costs $15,000 to $40,000 when professionally built.
What is the best screen for a screened porch?
Standard charcoal fiberglass mesh suits most homes. Choose pet-resistant mesh if you have dogs or cats, fine no-see-um mesh near water, and solar mesh on hot, sun-facing porches.
Do I need a permit to screen in my porch?
Screening an existing covered porch often does not need a permit, but rules vary. Adding a roof, posts, footings, or electrical work almost always requires one, so check with your local building department and HOA first.