Home Improvement

Behr Waterproofing Stain and Sealer: Opacities and Colors

Behr Waterproofing Stain and Sealer: Opacities and Colors

Most deck stain disappointments come from choosing the wrong opacity, not the wrong color. The Behr waterproofing stain and sealer family comes in three levels of see-through: a transparent finish that shows nearly all the grain, a semi-transparent stain that tints the wood while letting grain show, and a solid color stain that hides grain like a thin paint. Each one behaves differently on a deck floor versus a fence or siding.

The quick guide: choose transparent for newer, good-looking wood you want to keep natural; semi-transparent for most decks and fences that need color but should still look like wood; and solid color for older, weathered or mismatched boards, especially on vertical surfaces. Solid stains form a film, and on horizontal deck boards that film can wear and peel in traffic lanes, so many contractors favor penetrating products for decks.

Product names, colors and specs were checked against the manufacturer’s product pages and retailer listings. Formulas and color lineups change, so read the current label before you buy.

Behr Waterproofing Stain and Sealer Opacity Comparison

Opacity Product name Grain visibility Example colors Best for
Transparent Premium Transparent Waterproofing Wood Finish Full grain, light tint Natural, Cedar Naturaltone, Redwood (pre-mixed) New or recently cleaned wood in good condition
Semi-transparent Premium Semi-Transparent Waterproofing Stain and Sealer Grain shows through color ST-101 Atlantic, ST-103 Coffee, ST-104 Cordovan Brown, ST-105 Padre Brown, ST-108 Forest Most decks, fences and furniture with moderate weathering
Solid color Premium Solid Color Waterproofing Stain and Sealer Grain hidden, texture remains Dozens of colors, such as SC-102 Slate, SC-103 Coffee, SC-533 Cedar Naturaltone Weathered wood, siding, fences, mismatched boards

Stains do not carry an LRV the way wall paints do, so judge color on a test board of your actual wood. The same stain looks very different on pressure-treated pine, cedar and redwood.

Transparent: Keep the Natural Look

The transparent version is sold as a waterproofing wood finish rather than a “stain and sealer,” but it belongs to the same family. The manufacturer lists three pre-mixed colors, Natural, Cedar Naturaltone and Redwood, plus a small set of custom tints. It adds a light wash of color and water repellency while letting nearly all the grain show.

The trade-off is protection. With little pigment, transparent finishes offer the least UV blocking, so they gray and fade fastest. Expect to recoat more often than with the other opacities, particularly on decks with full sun.

The semi-transparent stain and sealer adds noticeably more color while still letting grain show through. Color names include Atlantic, Slate, Coffee, Cordovan Brown, Padre Brown, Bordeaux and Wedgewood (ST-101 through ST-107), with further colors such as Forest (ST-108) in the lineup.

Manufacturer figures for this product list coverage of about 250 to 300 sq ft per gallon for the first coat and 500 to 600 sq ft for the second. Directions call for two thin coats and say not to thin the product. Recoat time is about 1 to 2 hours in mild conditions, light foot traffic after 24 to 48 hours, and a full cure around 72 hours. It is intended for new to moderately weathered, unsealed exterior wood; heavily weathered or previously coated wood needs stripping and cleaning first.

Recoating in a different color

Because semi-transparent stain is partly see-through, the existing color will influence the new one. Going darker is easy. Going lighter usually requires stripping back to bare wood.

Solid Color: Maximum Coverage

The solid color waterproofing stain and sealer comes in dozens of colors and forms a film that hides grain and minor imperfections while keeping the wood’s texture. It is ideal for siding, fences, railings and older decks with patched or mismatched boards. Manufacturer guidance lists light foot traffic after 24 to 48 hours and heavy foot traffic after 72 hours, with second-coat coverage around 400 to 800 sq ft per gallon.

Two cautions. First, on cedar and redwood, which contain water-soluble extractives, the manufacturer recommends priming before applying white and pastel colors to prevent bleed-through. Second, film-forming stains can peel on horizontal deck boards where foot traffic and standing water are heavy. Several reviewers and contractors describe solid stain as an excellent fence and siding coating but a less forgiving deck floor coating.

Picking Behr Exterior Stain Colors That Work Together

Color choice gets easier once the opacity is settled. Browns such as Coffee, Cordovan Brown and Padre Brown hide dirt and pollen well on deck floors and suit traditional homes with brick or warm siding. Grays such as Slate look current on modern exteriors and pair well with white trim and black railings, but light grays show footprints and tannin stains more readily. Blues and greens such as Atlantic, Wedgewood and Forest are usually best on fences, sheds and siding rather than heavily walked floors.

A common two-tone approach uses a darker semi-transparent or solid color on deck floors and a lighter solid color on railings and skirting. The darker floor hides wear, and the lighter railings brighten the structure. If you plan to use two products, check that both are compatible over each other and that the floor color goes on first so drips on the floor are covered.

How wood species changes the result

Pressure-treated pine often has a green or yellow cast that shifts translucent colors, so a cedar-toned semi-transparent may look more orange on pine than on the color card. Cedar and redwood have natural red-brown tones that warm any transparent or semi-transparent color. Older gray wood absorbs stain unevenly unless it is cleaned and brightened. Always judge behr exterior stain colors on a scrap or hidden board of your own wood, dried fully, before committing to gallons.

Looking to buy Behr Waterproofing Stain and Sealer? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Prep and Application Steps

The opacity you choose matters less than prep. Stain failure is usually a prep failure.

  1. Check the weather. Pick a dry stretch with no rain expected and moderate temperatures. Avoid direct midday sun on the boards.
  2. Repair the wood. Replace rotten boards, set popped nails and sand splinters.
  3. Strip if needed. Remove failing film or a different product type with a wood stripper.
  4. Clean and brighten. Use a wood cleaner to remove dirt, mildew and gray fibers. Rinse thoroughly.
  5. Let it dry. Most woods need at least a couple of dry days after cleaning. New pressure-treated lumber often needs longer before it accepts stain.
  6. Test a board. Apply the chosen color to an inconspicuous spot and let it dry.
  7. Apply thin coats. A deck stain applicator pad on a pole covers boards quickly; use a brush for gaps, end grain and railings. Work two or three boards at a time along their full length to avoid lap marks.
  8. Back-brush and avoid puddles. Excess stain that sits on the surface stays tacky and can peel.

Safety: Rags, Vapors and Ladders

Rags and applicator pads soaked with oil-based stains or penetrating oils can heat up and ignite on their own as they dry. Lay used rags flat outdoors to dry, or put them in a metal container filled with water and a tight lid, then dispose of them according to local rules. Never pile oily rags in a corner, bucket or trash bag. Keep stain cans and wet rags away from grills, fire pits, heaters and pilot lights, and do not smoke while staining.

Water-based stains are lower in odor, but still ventilate garages and enclosed porches, wear gloves and eye protection, and keep strippers and cleaners separate; never mix chemical products. For siding and second-story railings, use a stable ladder on level ground or hire a pro.

Troubleshooting Stain Problems

  • Peeling. Usually solid stain on a deck, too-thick coats or stain over a dirty or previously sealed surface. Strip and switch to a penetrating option on floors.
  • Blotchy color. Uneven wood absorption or lap marks. Keep a wet edge and apply in full-board lengths.
  • Tacky surface days later. Too much product or cool, damp weather. Wipe excess and allow more time.
  • Bleed-through on light colors. Cedar and redwood extractives; prime before a white or pastel solid stain.
  • Rapid fading. Transparent finishes in full sun fade fastest; step up to semi-transparent for more UV protection.

Cost and When to Hire a Pro

Gallons in this family generally fall in a moderate price range, with 5-gallon pails offering better value for large decks and fences. A 300-square-foot deck often needs 2 to 3 gallons for two coats of semi-transparent. Professional deck cleaning and staining commonly runs from several hundred dollars for a small deck to a few thousand for large or multi-level decks, with stripping adding cost. Hire a pro for elevated decks, rotted framing or loose railings, which are structural safety issues rather than finish problems.

Whichever opacity you choose, the Behr waterproofing stain and sealer lineup works best on clean, dry, properly prepared wood with thin, even coats.

Frequently Asked Questions

Which opacity is best for a deck?

Semi-transparent is the most common choice for decks because it adds color and UV protection without forming a thick film that can peel underfoot.

How many colors does the solid stain come in?

The solid color waterproofing stain and sealer comes in dozens of colors, including grays, browns and blues. Check the current Behr color card for the full list.

How long before I can walk on the stained deck?

Plan on 24 to 48 hours for light foot traffic and about 72 hours before heavy use or furniture, longer in cool or humid weather.

Can I apply solid stain over semi-transparent?

Generally yes, after cleaning and once the surface is fully dry. Going from solid back to semi-transparent requires stripping.

How much does a gallon of semi-transparent cover?

About 250 to 300 sq ft for the first coat and 500 to 600 sq ft for the second, per manufacturer figures.

Is the transparent product a stain?

It is sold as a transparent waterproofing wood finish with a light tint, so it behaves like a clear sealer with subtle color rather than a true stain.