Home Improvement

Behr Solid Stain Colors: Palette, Coverage and Prep

Behr Solid Stain Colors: Palette, Coverage and Prep

A solid stain looks a lot like paint once it dries, but it behaves differently on wood, and picking the wrong shade or skipping prep is the fastest way to end up with peeling boards. Behr solid stain colors are sold mainly in BEHR PREMIUM Solid Color Waterproofing Stain & Sealer, a 100% acrylic, water-cleanup product that hides wood grain completely while leaving some surface texture visible. The standard palette uses codes starting with “SC,” such as SC-104 Cordovan Brown, and the base can also be tinted to a very large range of custom colors.

Behr’s technical literature for this stain lists coverage of about 200 to 400 square feet per gallon depending on application method and how porous the wood is, a recoat window of 1 to 2 hours, and light foot traffic after 24 to 48 hours. Those numbers make sense only on clean, dry, properly prepared wood, so prep gets as much attention here as the colors.

Behr Solid Stain Colors and Specs at a Glance

Color codes come from Behr’s color listings and retail product labels. LRV figures were not available for these stain colors when this was checked, so judge lightness from a real sample on your own wood.

Spec or color Value What it means
Product BEHR PREMIUM Solid Color Waterproofing Stain & Sealer 100% acrylic solid stain for decks, fences and siding
Coverage About 200 to 400 sq ft per gallon Rough or weathered wood lands at the low end
Recoat time 1 to 2 hours at 77°F and 50% humidity Two thin coats beat one heavy coat
Light foot traffic / full cure 24 to 48 hours / 72 hours Keep furniture off the deck until cured
SC-104 Cordovan Brown Deep brown Behr’s first Exterior Stain Color of the Year (2023)
SC-330 Redwood Red-brown Classic deck and fence shade
SC-533 Cedar Naturaltone Warm orange-brown Mimics fresh cedar with full hide
SC-129 Chocolate Dark brown Hides worn, mismatched boards well
SC-102 Slate Dark gray Popular modern gray for decks

Behr’s current product claims for this stain describe protection of up to 10 years on decks and up to 25 years on fences and siding. Real service life depends on sun, traffic and prep.

Browns and reds

Browns remain the most requested shades because they hide dirt, pollen and foot traffic. SC-104 Cordovan Brown is a deep, versatile brown that Behr chose as its first Exterior Stain Color of the Year, and it pairs easily with neutral siding. SC-129 Chocolate is darker still, and Padre Brown sits in the same family. SC-330 Redwood and SC-533 Cedar Naturaltone give the traditional warm wood look without showing the grain or mismatched boards underneath.

Grays

Gray solid stains suit modern homes and gray or white siding. SC-102 Slate is a dark gray that hides dirt far better than pale grays. Very light grays and whites look crisp but show every footprint and tannin stain on a deck floor, so they are usually better on fences and railings.

Greens and blues

Greens such as SC-108 Forest and SC-120 Ponderosa Green blend fences and sheds into landscaping. SC-132 Sea Foam is a lighter, coastal choice for trim and outbuildings. Because the base can be tinted to custom colors, you can also match siding or shutters.

Choosing a shade for your deck

  • Heat: dark colors absorb more sun, so deck boards get noticeably hotter underfoot.
  • Dirt and wear: mid browns and mid grays hide traffic patterns better than very dark or very light shades.
  • Siding contrast: pick a stain a few shades darker or lighter than the house so the deck reads as its own surface.
  • Sample first: brush a sample on a scrap board from the deck itself, let it dry fully and view it in morning and afternoon light.

Solid stain vs semi-transparent

Solid stain is the right pick when boards are weathered, mismatched or patched with new lumber, because it hides the grain and evens out color. Semi-transparent stain lets the grain show and wears away gradually rather than peeling, but it cannot hide repairs. Once a deck has solid stain, switching back to a see-through finish generally means stripping it first.

Prep: The Step That Decides How Long It Lasts

Solid stains fail when they go over dirty, wet or loosely coated wood. Behr’s directions call for cleaning and brightening the wood, stripping old coatings when needed and letting everything dry before application.

  1. Check the weather. Plan for a dry stretch with no rain expected for 24 hours and temperatures within the label range. Avoid direct midday sun and hot boards.
  2. Remove loose coatings. Scrape or strip peeling paint or stain. If the wood has an old finish that is failing, a wood stain stripper is the usual step.
  3. Clean and brighten. Use a wood cleaner to remove dirt, mildew, algae and gray weathered fibers. On new wood, a cleaner also removes mill glaze so the stain can soak in.
  4. Rinse and dry. Rinse thoroughly and let the wood dry, typically at least a couple of dry days.
  5. Sand lightly. Knock down raised fibers or fuzz after cleaning.
  6. Prime where needed. Redwood, cedar and cypress contain water-soluble tannins that can bleed through light colors, so prime those woods first when using pale shades. Previously painted surfaces also need primer per the label.

How to Apply Solid Stain

  1. Stir well. Solid stain must be tinted before use; stir the can thoroughly and mix multiple cans together for an even color.
  2. Cut in first. Brush gaps, end grain and edges where a roller or pad can’t reach.
  3. Apply thin coats. Use a nylon/polyester brush, a 3/8-inch nap roller or a deck stain applicator pad, working two or three boards at a time from end to end to keep a wet edge.
  4. Back-brush. If spraying, follow immediately with a brush or pad to work the stain in and remove puddles.
  5. Second coat. After 1 to 2 hours (longer in cool or humid weather), apply a thinner second coat.
  6. Let it cure. Allow 24 to 48 hours before light foot traffic and 72 hours before furniture and grills go back.

Over-application is the most common mistake. Thick films on horizontal decking trap moisture and lead to peeling and cracking, so keep coats thin and even.

Looking to buy Behr Solid Stain Colors? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Fire and Chemical Safety

Acrylic solid stain cleans up with water, but the prep products and the job site still need care. Wear gloves and eye protection when using strippers and cleaners, keep products off plants and never mix different cleaning chemicals. If you use any oil-based product during prep or on nearby trim, lay used rags flat outdoors to dry or store them in a sealed, water-filled metal container, because oil-soaked rags can heat up and ignite on their own. Store cans away from furnaces, water heaters and direct sun, and protect them from freezing. On older homes, assume old paint could contain lead: test before scraping or sanding, and use lead-safe practices.

Troubleshooting Solid Stain Problems

Peeling within a year: usually caused by staining wet wood, skipping cleaning or applying too heavily. Strip loose areas, clean, dry and recoat thinly.

Blotchy color: uneven absorption between new and weathered boards, or mixing cans from different batches. Box the cans together before starting.

Brown or orange bleed on light colors: tannin bleed from cedar or redwood. Spot-prime with a stain-blocking exterior primer and recoat.

Slippery surface: stained decks can be slick when wet. Keep shaded decks clean of algae and mildew, and consider a light-traction additive if the label allows one.

Cost and When to Call a Pro

Solid stain typically costs a moderate amount per gallon, and most decks need several gallons for two coats, plus cleaner, stripper and applicators. Professional deck staining usually runs a few dollars per square foot, more when heavy stripping or board replacement is needed.

Hire a pro when the deck has widespread peeling over multiple old coatings, when boards or railings are rotted or loose, when a second-story deck requires work from ladders, or when lead paint is suspected on an older home.

How Much Behr Premium Solid Stain to Buy and How Long It Lasts

Plan on one gallon of Behr Premium solid stain for every 200 to 400 square feet per coat, using the low end for rough, weathered or porous wood. Most decks need two thin coats, so double the single-coat figure and add a little extra for railings, stairs and end grain.

Gallon Estimates for Two Coats

Surface area Smooth or newer wood Rough or weathered wood
200 sq ft deck About 1 to 2 gallons About 2 gallons
400 sq ft deck About 2 to 3 gallons About 4 gallons
600 sq ft deck About 3 to 4 gallons About 6 gallons
100 ft of 6 ft fence, one side About 3 to 4 gallons About 6 gallons

Railings and balusters use far more stain than their footprint suggests. As a rough guide, add one gallon for every 30 to 40 linear feet of railing with spindles. Buy all the cans at once and box them together so the color stays even.

How Long It Lasts on Each Surface

Behr’s label claims for this product have described up to 10 years on decks and up to 25 years on fences and siding, but real service life depends on sun, foot traffic and prep. Horizontal deck boards take the most abuse from standing water, grit and furniture, so they wear first. Vertical surfaces such as fences and siding shed water and usually hold color far longer.

Signs It Is Time to Recoat

  • Water soaks in instead of beading on the boards.
  • Color has faded or worn through in traffic lanes, at stair treads or around the grill.
  • Small areas are peeling or flaking along board ends.

Maintenance Coats

When the existing coat is sound and simply worn, a full strip is not needed. Clean the surface, let it dry, scrape and sand any loose spots, then apply one thin coat of the same color. Recoating before the stain fails keeps film buildup low. Too many heavy coats on a deck floor eventually crack and peel together, which forces a full strip. Spot-touching only the worn lanes rarely blends well, so recoat full boards end to end. Check the current label on your can for the exact coverage and recoat guidance, since product versions change.

Frequently Asked Questions

Browns such as SC-104 Cordovan Brown, SC-129 Chocolate and SC-330 Redwood are long-running favorites, along with SC-533 Cedar Naturaltone and SC-102 Slate. Custom tinting covers almost any other shade.

How much does a gallon of Behr solid stain cover?

Behr’s technical data lists about 200 to 400 square feet per gallon, depending on application method and how porous the wood is. Rough or weathered wood uses more.

Do I need two coats of solid stain?

Two thin coats are the usual recommendation for even color and protection. Keep the second coat thinner than the first.

Can I put solid stain over old paint?

Yes, on properly prepared surfaces, but remove loose paint and prime previously painted areas as the label directs.

Do Behr solid stain colors have an LRV?

LRV values are not commonly listed for stain colors the way they are for paint chips. View a dried sample on your own wood in daylight to judge how light or dark it reads.