Home Improvement

Door Hinge Sizes: Chart for Interior, Exterior and Heavy Doors

Door Hinge Sizes: Chart for Interior, Exterior and Heavy Doors

Most hinge problems start with buying the wrong size, not a bad install. The common door hinge sizes for homes are 3-1/2 inch for standard interior doors, 4 inch for heavier interior and many exterior doors, and 4-1/2 inch for solid exterior and heavy doors. The height of the hinge leaf is the number on the package, and it scales with how thick, wide and heavy the door is.

A typical hollow-core bedroom door that is 1-3/8 inches thick and 30 to 32 inches wide hangs fine on three 3-1/2 inch hinges. A 1-3/4 inch thick entry door, solid-core interior door, or anything wider than 36 inches should move up to 4 or 4-1/2 inch hinges, and very wide or oversized doors call for 5 inch heavy-weight hinges. Corner shape matters too: replacement hinges must match the existing mortise, either square, 1/4 inch radius, or 5/8 inch radius.

Count matters as much as size. Doors up to about 60 inches tall need two hinges, standard 80 inch doors need three, and taller or very heavy doors need four. Get those three numbers right (height, corner and count) and the door will swing cleanly for decades.

Door Hinge Sizes Chart by Door Type

Use this chart to match standard door hinge size to the door you have. The figures follow common residential practice and the general sizing guidance used by hardware makers for butt hinges.

Door type Door thickness Door width Hinge size (height) Hinges per door
Hollow-core interior 1-3/8 in Up to 32 in 3-1/2 in 2 or 3
Solid-core interior 1-3/8 in 32 to 36 in 3-1/2 or 4 in 3
Closet or cabinet-height door 1-3/8 in Up to 24 in 3 to 3-1/2 in 2
Exterior entry door 1-3/4 in Up to 36 in 4 or 4-1/2 in 3
Heavy solid wood or fire-rated door 1-3/4 in Up to 36 in 4-1/2 in heavy-weight 3 or 4
Wide door 1-3/4 in 36 to 48 in 5 in heavy-weight 4
Tall door (8 ft) 1-3/8 to 1-3/4 in Up to 36 in Match the thickness rows 4

When a door falls between two rows, size up. A slightly larger hinge never hurts a door, while an undersized one lets the door sag, rub the head jamb and pull screws loose over time.

How Hinge Size Is Measured

Butt hinges are listed as height by width with the leaves open flat. A “3-1/2 x 3-1/2” hinge is 3-1/2 inches tall along the pin and 3-1/2 inches across both open leaves. Height is the dimension that matters for load. Width is chosen so the barrel clears the door casing when the door swings fully open.

To measure an existing hinge, open the door, then measure the leaf from top edge to bottom edge, ignoring the knuckle caps or finials. Then check the corners. Lay a coin against the corner: a quarter fits a 5/8 inch radius almost exactly, while a 1/4 inch radius corner is a much tighter curve. Square corners have no curve at all.

Corner Shapes and Why They Matter

  • 5/8 inch radius: the most common corner on prehung interior doors in newer homes. The mortise is routed with a template, which leaves rounded ends.
  • 1/4 inch radius: found on many exterior prehung doors and some interior units. It looks nearly square but has a small curve.
  • Square corners: common on older doors and any door hung with a chisel. Square hinges also suit commercial frames.

If you swap a square hinge into a radius mortise, gaps show at each corner. If you go the other way, the hinge will not sit flush until you square the mortise ends with a sharp chisel. Matching the corner saves that work.

Leaf Thickness and Weight Rating

Hinges come in standard weight and heavy weight. Standard-weight leaves are thinner and suit most residential doors. Heavy-weight hinges use thicker leaves and often ball bearings, and they belong on solid entry doors, doors with closers, and high-traffic doors. Ball-bearing hinges reduce wear at the knuckle, which keeps a heavy door from sagging. Check the package for a weight capacity per set, since ratings vary by product.

How Many Hinges Does a Door Need

The old rule of thumb is one hinge for every 30 inches of door height, rounded up. That gives the familiar counts:

  • Doors up to 60 inches tall: 2 hinges
  • Doors 60 to 90 inches tall (the standard 80 inch door): 3 hinges
  • Doors 90 to 120 inches tall: 4 hinges

Add a hinge for weight as well as height. A solid-core 80 inch door is stable on three hinges, but a heavy solid hardwood or oversized door benefits from a fourth. Some older hollow-core doors were hung on two hinges; adding a third middle hinge is a cheap fix for a door that has started to warp or rub at the latch side.

Standard Hinge Placement

Placement varies by builder, though most residential doors follow one of two layouts. A common layout sets the top hinge 7 inches from the top of the door to the top of the hinge and the bottom hinge 11 inches from the bottom of the door to the bottom of the hinge. Another uses 5 inches at the top and 10 inches at the bottom. The middle hinge is centered between the two, or on some doors placed closer to the top hinge to resist sag. For replacement work, simply reuse the existing mortises.

Tools and Materials for Changing Hinges

Swapping hinges is one of the easier door jobs. A hinge pack in the correct size, corner radius and finish usually costs less than a single specialty tool, and buying a door hinge pack keeps every hinge on the door matched in color and pin style.

  • Replacement hinges matched for height, corner radius and finish
  • Tape measure and a coin or radius gauge for checking corners
  • Screwdriver or drill with a matching bit (most hinge screws are Phillips)
  • Sharp 1 inch wood chisel and hammer, only if you change corner style
  • Wood shims or a thin wedge to support the door while you work
  • Wood glue and toothpicks or dowels for stripped screw holes
  • A few longer screws for the jamb side on exterior doors
Looking to buy Door Hinge Sizes? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

How to Replace Hinges Step by Step

  1. Confirm the size. Measure one existing hinge for height, width and corner radius before you shop. Note the finish so new hinges match the knob and lock.
  2. Support the door. Slide a shim or folded cardboard under the latch side so the door cannot drop when a hinge is removed.
  3. Swap one hinge at a time. Remove the screws from one hinge, fit the new one into the same mortise, and drive the screws. Doing them one at a time keeps the door aligned.
  4. Drive screws straight. Angled screw heads stick up and keep the leaves from closing fully, which causes binding.
  5. Fix stripped holes. If a screw spins, pack the hole with glue-coated toothpicks or a small dowel, let it dry, trim flush, and redrill.
  6. Test the swing. The door should close without rubbing the jamb or head, and the gap along the latch side should look even from top to bottom.

If you are moving from two hinges to three or from 3-1/2 to 4 inch hinges, you will need to cut new or larger mortises in both the door and the jamb. A hinge template and router make that faster and cleaner than chiseling, especially for 5/8 inch radius corners.

Troubleshooting Hinge Size Problems

Door sags at the latch side. The top hinge is usually the culprit. Check for loose screws first. If the screws are tight, the hinge may be too small or too light for the door. Upgrading to heavier or ball-bearing hinges, or adding a longer screw into the stud at the top hinge, typically pulls the door back into line.

New hinge will not sit flush. Either the corner radius does not match or the new leaf is thicker than the old one. Square up the mortise ends or deepen the mortise slightly with a chisel.

Door springs open after closing. This is called hinge bind. Screw heads that protrude, a mortise cut too deep, or a door that hits the stop too early can all cause it. Drive the screws flush and check the stop position.

Barrel hits the casing. The hinge is too narrow for the trim depth. A wider leaf moves the pin out so the door can open past the casing.

Keep a note of your door hinge sizes, corner radius and finish on the inside of a closet door or in your phone. When a hinge breaks or you repaint and want new hardware, that single record saves a trip back to the store.

Hinge Costs and Buying Tips

Residential hinges are inexpensive. Standard 3-1/2 inch interior hinges commonly run a few dollars each, and multi-packs bring the price down further. Heavy-weight and ball-bearing 4 to 4-1/2 inch hinges cost more per piece, and specialty finishes, security pins or spring hinges add to the price. Budget a modest amount for a full house of matched hinges compared with replacing doors.

For exterior doors that open outward, choose hinges with non-removable pins or a security stud so the door cannot be lifted off when the pins are exposed. Self-closing spring hinges, often required between an attached garage and the house in many areas, are sized the same way as standard hinges but need tension adjustment after install. Check local code for garage-to-house door requirements before you buy.

When to Call a Pro

Swapping hinges in existing mortises is a simple DIY job. Call a carpenter when you need to rehang a door with new mortises, convert to a larger hinge on a heavy entry door, correct a frame that has shifted out of square, or install hinges on a fire-rated door, where the hinge type and count must match the door’s listing. A pro can also tell you if a sagging door is a hinge issue or a settling problem in the framing around the opening.

Frequently Asked Questions

What is the standard door hinge size for interior doors?

The standard interior hinge is 3-1/2 by 3-1/2 inches, used on 1-3/8 inch thick doors up to about 32 inches wide. Solid-core or wider interior doors often use 4 inch hinges.

What size hinges do exterior doors use?

Most 1-3/4 inch thick exterior doors use 4 inch or 4-1/2 inch hinges, with three per door. Heavy or oversized entry doors move to 4-1/2 inch heavy-weight or 5 inch hinges.

How do I know if my hinge has a 1/4 or 5/8 inch radius?

Hold a quarter against the corner. If its edge matches the curve, it is a 5/8 inch radius. A much smaller curve is a 1/4 inch radius, and no curve means square corners.

Can I put a 4 inch hinge on a door with 3-1/2 inch hinges?

Yes, but you must lengthen the mortises in both the door and the jamb by about 1/2 inch so the larger leaf sits flush. A hinge template and router keep the cuts clean.

Do I need three hinges on an 80 inch door?

Three hinges are standard and recommended for 80 inch doors. Two can work on very light hollow-core doors, but a third hinge keeps the door from warping and reduces sag.

Are door hinge dimensions the same on every brand?

The common sizes and corner radii are standard across the industry, so a 3-1/2 inch, 5/8 radius hinge from one maker fits a mortise cut for another. Leaf thickness and screw-hole patterns can vary slightly.