Ordering a new front door seems simple until you realize there are three different sizes involved: the door slab itself, the prehung unit with its frame, and the rough opening in the wall. Mix them up and the door either will not fit or leaves gaps you cannot hide with trim. Standard exterior door dimensions in the United States are 36 inches wide by 80 inches tall for a front entry door, with 32 and 30 inch widths common for side, back and garage entry doors. Taller 96 inch (8 foot) doors are popular in homes with 9 or 10 foot ceilings.
Part of our Windows & Doors guide — explore the full guide →
For a 36 by 80 inch slab, a prehung unit usually measures about 37.5 by 81.5 inches outside the frame, and the rough opening should be about 38 by 82 inches. Those relationships hold for most sizes: add roughly 2 inches to the slab width and 2 to 2.5 inches to the slab height to get the rough opening. Odd and custom openings follow their own rules, but they start from the same math.
- Standard Exterior Door Dimensions Chart
- Standard Front Door Width
- Standard Exterior Door Height
- Slab vs Prehung Door Sizes
- Rough Opening for Entry Door Installations
- Average Front Door Dimensions in Older Homes
- Installation Overview
- Safety and Structural Notes
- Troubleshooting Fit Problems
- Cost Ranges
- When to Call a Pro
- Standard Front Door Size Compared With Back, Patio, and Custom Doors
- Frequently Asked Questions
- What is the standard size of an exterior door?
- What rough opening do I need for a 36 inch exterior door?
- Are exterior doors bigger than interior doors?
- Can I get a custom size entry door?
- Should I buy a slab or prehung exterior door?
- What size are mobile home exterior doors?
- What are standard exterior door sizes in millimeters?
- What rough opening does a double exterior door need?
- What type of door is required between a garage and a house?
Standard Exterior Door Dimensions Chart
These are the most common house door dimensions for swinging exterior doors. Rough opening numbers are typical; always confirm against the manufacturer’s sizing sheet for the exact unit you buy.
| Door slab (W x H) | Typical prehung unit | Typical rough opening |
|---|---|---|
| 30 x 80 in | 31.5 x 81.5 in | 32 x 82 in |
| 32 x 80 in | 33.5 x 81.5 in | 34 x 82 in |
| 34 x 80 in | 35.5 x 81.5 in | 36 x 82 in |
| 36 x 80 in | 37.5 x 81.5 in | 38 x 82 in |
| 36 x 96 in | 37.5 x 97.5 in | 38 x 98 in |
| 42 x 80 in | 43.5 x 81.5 in | 44 x 82 in |
Door thickness for exterior slabs is almost always 1.75 inches, compared with 1.375 inches for most interior doors. Jamb depth for a prehung unit typically matches a 2×4 wall at about 4.5 to 4.625 inches or a 2×6 wall at about 6.5 to 6.625 inches, and jamb extensions handle thicker walls.
Standard Front Door Width
The standard front door width is 36 inches. It is wide enough to move furniture and appliances through, gives a welcoming look from the street, and meets the clear width most accessibility guidelines recommend for a main entrance. A 36 inch front door provides roughly 32 to 33 inches of clear passage when the door is open 90 degrees, because the door thickness and stops eat into the opening.
Narrower entry door sizes still have a place. A 32 inch door is common for back doors, mudroom entries and doors from an attached garage. A 30 inch door shows up in older homes, small cottages and secondary entrances. In general, the more often you move large items through a door, the more you will appreciate the extra width, and many builders now use 36 inches for every exterior door when wall space permits.
Wider Entrance Door Sizes
Grand entries can use 42 inch single doors, or a combination of a door with sidelites. Sidelites are the narrow fixed glass panels beside the door, commonly 10, 12 or 14 inches wide. A 36 inch door with two 12 inch sidelites makes a unit roughly 64 inches wide overall. Double entry doors pair two 30 or 36 inch slabs for a 60 or 72 inch total width. These configurations need a header sized for the larger span, and sizing that header is a structural job.
Standard Exterior Door Height
The standard exterior door size for height is 80 inches, which matches most interior doors and suits 8 foot ceilings. In homes with 9 foot or taller ceilings, 96 inch doors look more in proportion and let more light in when they include glass. Some manufacturers also offer 84 inch doors for in-between situations.
Taller doors mean a taller rough opening and header. Switching from 80 to 96 inches in an existing wall involves moving the header up, which may require reframing and a permit. If the change is part of a larger remodel, it is easier to plan from the start.
Slab vs Prehung Door Sizes
Understanding the difference saves a lot of confusion when you shop.
- Slab door: just the door panel, sold by its actual width and height, such as 36 by 80. You hang it in your existing frame. This works only when the old frame is square, sound and the same size.
- Prehung door: the slab already hung on hinges in a frame with jambs, weatherstripping, a sill or threshold and sometimes exterior brickmold trim. It is sized by the slab dimension but measures larger overall.
For most exterior replacements, a prehung exterior door is the better option because it comes with a new threshold and weather seals that are hard to match on an old frame. It also makes a rotted or out-of-square frame a non-issue.
Rough Opening for Entry Door Installations
The rough opening for entry door framing is the space between the jack studs at the sides and from the subfloor to the bottom of the header. Most manufacturers want about 2 inches of extra width and 2 to 2.5 inches of extra height compared with the slab size. That gap leaves room to shim the frame plumb and square.
Exterior door dimensions rough opening specs vary a bit by brand and by threshold style. An adjustable threshold, a raised sill for a slab-on-grade home, or a unit with a built-in sill pan can change the height needed. Always read the manufacturer’s rough opening dimension before cutting or reframing.
How to Measure an Existing Door
- Measure the width of the slab at the top, middle and bottom, and the height at the hinge side and latch side.
- Note the jamb depth from the inside edge of the interior casing area to the outside face of the frame.
- Remove interior trim if possible and measure the rough opening between the studs and from the floor to the header.
- Use the smallest width and height measurements when ordering, because older openings are rarely perfectly square.
- Check the swing direction (left-hand or right-hand, inswing or outswing) while standing outside facing the door.
Average Front Door Dimensions in Older Homes
Older houses often have average front door dimensions that do not match modern standards. Homes built before the mid 1900s may have 30 or 32 inch front doors, heights of 78 or 79 inches, or 1.375 inch slabs. Settling and decades of paint also change the opening. When you find odd size entry doors like these, you have three main options:
- Order a custom size entry door built to the exact opening.
- Reframe the rough opening to fit a standard prehung unit.
- Have a slab trimmed or built to fit the existing frame, if the frame is in good shape.
Custom doors cost more and take longer to arrive, often several weeks, but they preserve original trim and siding. Reframing to a standard size can be the cheaper long-term choice if the exterior trim is being replaced anyway.
Installation Overview
Replacing an exterior door is a common DIY project for experienced homeowners when the new unit matches the rough opening. The basic sequence:
- Remove the old door, frame and trim, and inspect the subfloor and framing for rot.
- Install a sill pan or flashing tape across the bottom of the opening so water drains outward.
- Apply sealant under the threshold and set the prehung unit in place.
- Shim the hinge side plumb, then the latch side, keeping the reveal even around the slab.
- Fasten through the jambs into the framing, using long screws through the top hinge into the stud.
- Insulate the gap with low-expansion foam, flash the exterior, and install trim.
Safety and Structural Notes
Any change to a rough opening in an exterior wall affects the structure. The header above the door carries load from the roof or upper floors, so widening an opening for a 42 inch door, sidelites or a double door requires a properly sized header and often a permit. Use temporary supports when removing load-bearing framing, and consult a contractor or engineer for wide openings. Anchor the door frame securely into the framing so it resists wind loads and forced entry. Homeowners associations may also have rules about door style and color, so check before ordering. If the project involves digging, such as building a new stoop or steps, call 811 before you dig to locate buried utilities.
Troubleshooting Fit Problems
- Door rubs at the top latch corner: the frame is out of plumb or the top hinge screws are short. Replace a top hinge screw with a long one into the stud.
- Light visible at the threshold: adjust the threshold or replace the door sweep.
- Rough opening too small: trim the jack studs only if they are not load-bearing beyond the header, or have a carpenter reframe.
- Drafts around the frame: foam or caulk was skipped. Remove trim and air seal the gap.
Cost Ranges
Steel and fiberglass prehung exterior doors in standard 32 and 36 inch widths are widely available and typically range from a few hundred dollars for basic models to well over a thousand for decorative glass or premium finishes. Solid wood and custom size entry doors cost more. Professional installation of a same-size prehung door is often several hundred dollars, while reframing, adding sidelites or enlarging an opening can push the total into the thousands.
When to Call a Pro
Hire a contractor if you are changing the rough opening size, replacing a header, dealing with rotted subfloor or sill framing, installing a heavy double or 96 inch door, or ordering a custom unit. A pro also makes sense when the door must meet energy or hurricane rating requirements in your area, since installation details affect the rating.
Standard Front Door Size Compared With Back, Patio, and Custom Doors
The standard front door size is 36 by 80 inches, but the doors at the back and sides of a house follow different conventions. A standard back door is usually 32 or 36 inches wide, while patio openings use wider sliding or hinged double units. When none of these fit the opening, a custom size front door is built to the exact frame instead.
Common Entrance Door Sizes by Location
| Door location | Common widths | Common heights | Notes |
|---|---|---|---|
| Front entry, single | 36 in | 80 or 96 in | Sidelites add width to the overall unit |
| Back or kitchen door | 32 or 36 in | 80 in | Half glass or full glass slabs are common |
| Garage to house | 30 to 36 in | 80 in | Many areas require a fire-rated or solid door here |
| Sliding patio door | 60, 72, or 96 in overall | 80 in | Sold by overall frame size, not slab size |
| Hinged double or French patio door | 60 or 72 in overall | 80 or 96 in | Inswing or outswing |
| Storm door | 30, 32, or 36 in | 80 to 81 in | Sized to fit the entry door opening it covers |
Standard Back Door Size Choices
A 32 inch back door was the norm for decades, and many homes still have one. If you are replacing it and the wall allows, stepping up to 36 inches makes it far easier to carry groceries, coolers, and grills through. That change widens the rough opening, so it means new framing and a properly sized header rather than a simple swap.
When a Custom Size Front Door Makes Sense
Custom doors are worth the extra cost and wait in a few situations:
- Historic homes where the original trim, masonry, or siding would be damaged by reframing.
- Openings that are tall but narrow, such as 34 by 84 inches, which no standard prehung unit fits.
- Arched or eyebrow tops that need a matching slab and frame.
- Oversized pivot or 42 inch and wider entries that a stock catalog does not carry.
For a custom order, give the maker the rough opening width and height, the wall thickness for jamb depth, the swing direction, and the threshold type. Measure in at least three places for each dimension and report the smallest. Most makers ask for the final sign-off on a drawing before production starts, so check it carefully, because custom doors usually cannot be returned once built.
Frequently Asked Questions
What is the standard size of an exterior door?
The standard front door is 36 inches wide by 80 inches tall and 1.75 inches thick. Back and side doors are often 32 or 30 inches wide.
What rough opening do I need for a 36 inch exterior door?
A 36 by 80 inch door typically needs a rough opening about 38 inches wide by 82 inches tall. Check the manufacturer’s spec for the exact number.
Are exterior doors bigger than interior doors?
Usually. Exterior doors are thicker at 1.75 inches and the front door is often wider at 36 inches, while many interior doors are 28 to 32 inches wide and 1.375 inches thick.
Can I get a custom size entry door?
Yes. Many manufacturers build custom widths and heights for older homes with odd openings, though they cost more and take longer than standard sizes.
Should I buy a slab or prehung exterior door?
Prehung is usually best for exterior doors because it includes a new frame, threshold and weatherstripping, which are hard to match on an old frame.
What size are mobile home exterior doors?
Mobile home doors use their own sizes, most commonly 32 x 72, 34 x 76 and 36 x 76 inches, and they usually swing outward. They also mount differently, with a flange that fastens over the siding, so a standard house door will not fit a mobile home opening without reframing. Measure the existing door and opening, and buy a door made for manufactured homes.
What are standard exterior door sizes in millimeters?
A standard 36 x 80 inch front door is about 914 x 2032 mm, and a 32 x 80 inch door is about 813 x 2032 mm. A 30 x 80 inch door is about 762 x 2032 mm, and an 8-foot 36 x 96 inch door is about 914 x 2438 mm. The standard exterior slab thickness of 1.75 inches is about 44 mm.
What rough opening does a double exterior door need?
Roughly 2 inches wider and 2 to 2.5 inches taller than the two slabs combined. A pair of 36-inch doors (72 inches total) typically needs a rough opening of about 74 x 82 inches, and a pair of 30-inch doors about 62 x 82 inches. Double units vary more than single doors because of the astragal and frame design, so confirm the manufacturer’s exact number before framing.
What type of door is required between a garage and a house?
Under the International Residential Code, the door between an attached garage and the house must be solid wood or solid or honeycomb-core steel at least 1-3/8 inches thick, or a door rated for 20 minutes of fire resistance. Hollow-core interior doors do not qualify, and some local codes also require the door to be self-closing. Check with the local building department before buying.