On a low-slope roof, the field membrane almost never leaks first. The trouble starts where the membrane turns a corner, climbs a wall or wraps a curb, and that is exactly where flat roof flashing does its work. Water on a flat roof moves slowly and sometimes sits for hours, so every seam and termination has to hold against standing water, not just runoff. A single loose corner or a split at a parapet can feed water into the deck for months before a ceiling stain appears.
Part of our Roofing guide — explore the full guide →
The short answer: flat roofs need a metal edge (a gravel stop or drip edge) at the perimeter, preformed or field-formed flashing at inside and outside corners, membrane flashing running up curbs and walls at least 8 inches, and a termination bar or counterflashing to lock the top edge. The specific materials depend on whether your roof is EPDM rubber, TPO, PVC or modified bitumen, and you should always use flashing products made for that membrane.
How Flat Roof Flashing Differs From Sloped Roof Flashing
On a pitched roof, flashing relies on overlaps and gravity: water runs downhill over each layer. Flat roof flashing has to be continuous and bonded instead, because water can pond and back up into any lap. That means seams are glued, taped or heat-welded rather than simply overlapped, and flashings are tied into the field membrane so the whole roof acts like one sheet.
Each membrane family has its own methods:
- EPDM (rubber roof): seams and flashing use primer and seam tape or uncured rubber flashing, which stretches to form corners. Rubber roof flashing products include pressure-sensitive strips, pipe boots and inside and outside corner pieces.
- TPO and PVC: thermoplastic sheets are heat-welded with a hot-air welder. Flashings use non-reinforced membrane for corners and reinforced membrane for walls and curbs, plus coated metal that the membrane can weld to.
- Modified bitumen: torch-applied, cold-adhered or self-adhered rolls, with base flashing and a cap sheet flashing up walls and curbs. Torch work is a fire risk and belongs to trained roofers.
Never mix chemistries. Asphalt-based cement on EPDM, for example, degrades the rubber, and solvent primers for one membrane can damage another.
Roof Edges: Gravel Stops and Drip Edges
The perimeter is the first place wind grabs a flat roof. A gravel stop is a metal edge with a raised lip that holds ballast or gravel on the roof and gives the membrane a clean termination. A drip edge or fascia metal turns down over the face of the fascia to throw water clear. On roofs that drain over the edge to gutters, the edge metal must let water out, so a low lip or a gutter apron is used instead of a tall gravel stop.
Typical installation sets the edge metal over the membrane on a continuous wood nailer, fastens it every 3 to 4 inches in a staggered pattern, then strips in the horizontal flange with a strip of compatible membrane or tape, called a stripping ply, that extends several inches onto the field. Joints between metal lengths get a small gap for expansion and a cover plate or splice tape. Loose edge metal and failed stripping plies are the most common sources of wind blow-off and edge leaks on flat roofs.
Inside and Outside Corners
Corners concentrate stress. An inside corner occurs where two walls or a wall and curb meet with the corner pointing away from you. An outside corner wraps around a projection like a chimney or curb, with the corner pointing toward you. Both require the membrane to change direction in three dimensions, which is impossible with a flat sheet unless it is cut, folded or stretched.
Roof corner flashing comes in two forms. Preformed corners are molded pieces that fit over the corner and bond to the membrane on all sides; they are fast and consistent. Field-fabricated corners use uncured EPDM or non-reinforced TPO or PVC that can be stretched and formed by hand or with heat. Either way, the corner piece goes on after the base flashing so it covers the cuts and fishmouths (small wrinkles that act like funnels) at the corner.
When inspecting an older roof, look closely at corners for cracking, lifting edges, open fishmouths and shrinkage pulling the membrane away from the wall. Shrinkage is especially common on older EPDM and can tear corners open.
Curbs, Walls and Parapets
Rooftop equipment curbs, skylight curbs, hatches and parapet walls all need base flashing that rises well above the deepest likely ponding. A common minimum is 8 inches above the finished roof surface. On the wall, the flashing is fully adhered to a clean, solid substrate, never just draped.
The top edge is where water tries to get behind the flashing. Common terminations include:
- Termination bar: a metal or plastic bar screwed through the flashing into the wall every 6 to 8 inches, sealed with a compatible sealant along the top.
- Counterflashing: metal set into a reglet (a cut groove) in masonry or fastened to the wall above, overlapping the top of the base flashing and shedding water over it.
- Coping cap: on parapets, the flashing can run up and over the wall top and be covered by a metal coping that turns down both sides.
Curbs should be wrapped on all four sides, with the corners treated as outside corners, and the top of the curb covered by the equipment flange or a metal cap. Missing or loose counterflashing above a curb is a frequent hidden leak source on homes with flat-roof additions and porches.
Repairing Flashing With Tape and Roll Products
For small repairs on EPDM, pressure-sensitive EPDM flashing tape is the go-to product. It is sold in widths from about 3 to 12 inches and in rolls, and it bonds to cleaned, primed rubber. A roof flashing roll of self-adhered membrane can also cover longer runs at walls or edges on compatible membranes. For TPO and PVC, the best repair is a heat-welded patch of matching membrane; tapes exist, but welded patches last longer.
Basic EPDM flashing tape repair steps
- Clean the area. Scrub with the membrane maker’s cleaner or a mild detergent, rinse, and let it dry completely.
- Prime. Apply the compatible primer to the membrane where the tape will sit, extending a little past the patch outline. Let it flash off until tacky but not wet, per the label.
- Cut and round. Cut the tape at least 3 inches larger than the damage on every side and round the corners so they do not peel.
- Apply and roll. Peel the release liner gradually, set the tape without wrinkles, and roll firmly with a silicone seam roller from the center out.
- Seal edges if required. Some systems call for lap sealant along exposed tape edges.
Primers and cleaners are flammable and give off strong vapors. Work with good airflow, keep them away from flames, pilot lights and torches, and wear gloves and eye protection.
Roof Access and Safety
Flat roofs feel safe because they are level, which is exactly why people walk off the edge. Set ladders on firm ground at a 1-to-4 angle, extend them at least 3 feet above the roof edge, and tie them off. Stay well back from unprotected edges and skylights, which are not designed to hold your weight. Avoid working on wet or frosty membrane, which becomes very slippery. Any roof two stories or higher, and any job requiring a torch, should go to a professional roofer with proper fall protection and fire safety training.
Troubleshooting, Costs and When to Call a Pro
When a flat roof leaks, start at the flashing: check the edges, corners, curbs, walls, pipe boots and drains before assuming the field membrane failed. Look for open seams at the edge of stripping plies, lifted corners, cracked sealant at termination bars, and counterflashing pulled away from masonry. Ponding near walls or curbs puts constant pressure on those flashings and often points to a sagging deck or clogged drain that also needs attention.
For costs, a roll of EPDM flashing tape or a preformed corner typically runs from about $15 to $60, and small DIY repairs often stay under $100 in materials. Professional flashing repairs at a curb or a section of parapet commonly cost a few hundred dollars up to around $1,000 or more depending on access and materials. Reflashing all perimeter edges and walls on a larger flat roof can run into the low thousands, and if wet insulation or rotted decking is found, the scope grows.
Call a commercial or low-slope roofing contractor when leaks recur after repair, when you see widespread shrinkage or brittle membrane, when the deck feels soft, or when the roof is TPO, PVC or torch-down, which need specialized welding or torch equipment. Ask if the repair will preserve any existing warranty, since many membrane warranties require the maker’s approved flashing details.
Frequently Asked Questions
How high should flat roof flashing go up a wall?
A common minimum is 8 inches above the finished roof surface, and higher where water ponds or snow builds up. The top edge should be secured with a termination bar, counterflashing or coping.
Can I use any flashing tape on a rubber roof?
No. Use tape made for EPDM along with the matching primer. Asphalt-based tapes and cements can damage rubber membrane and will not bond reliably.
What is a gravel stop on a flat roof?
A gravel stop is a metal roof edge with a raised lip that holds gravel or ballast in place and provides a finished termination for the membrane at the perimeter.
Why do flat roof corners leak so often?
Corners force the membrane to change direction, which creates cuts, wrinkles and stress points. Shrinking membrane and building movement pull on corners first, so they crack or lift before the field does.
Is flat roof flashing a DIY job?
Small EPDM tape repairs on a single-story roof can be DIY with the right primer and tape. Welded TPO or PVC work, torch-applied products, parapet reflashing and any two-story roof are better left to a roofer.