A skylight that would be a simple job on an asphalt shingle roof becomes a precision project on metal. Shingle-style flashing kits depend on overlapping courses that metal panels simply do not have, so skylights in metal roofs need a raised curb shaped to the panel profile, a diverter that steers water around the uphill side, and sealants and fasteners made for metal. Get those three pieces right and a skylight on a metal roof can outlast the panels themselves.
Part of our Roofing guide — explore the full guide →
The approach differs by roof type. On standing-seam roofs, the curb usually spans between seams and ties into the panel above and below. On exposed-fastener panels such as corrugated or R-panel, the curb flange must match the rib pattern exactly so it can be sealed and screwed on the flats. We cover both.
If you are comparing this project with a standard shingle installation, keep in mind that most generic skylight instructions assume shingles and step flashing. None of that transfers to metal.
How Skylights in Metal Roofs Differ from Shingle Installs
Water on a metal roof moves fast and in concentrated channels. Each pan between ribs or seams carries its own stream straight down the slope. Any opening interrupts that flow, and the water backs up against the uphill side of the curb. With skylights in metal roofs, the whole install is about getting that stream to split around the opening and rejoin the pans below without ever reaching a seam you had to seal.
Three differences matter most:
- Curb mount, not deck mount. A curb mount skylight sits on a raised frame, lifting the glazing above the water path. Low-profile deck-mount units with shingle flashing kits are the wrong choice here.
- Profile-matched flashing. The curb base must mirror the panel ribs so it lies flat and can be sealed continuously.
- Thermal movement. Metal panels expand and contract with temperature. Standing-seam panels float on clips, so a rigid connection that pins the panel can tear sealant or distort the seam.
Choosing the Right Skylight and Curb
A curb mount skylight is the standard answer for metal roofs. You can either build a wood curb on the roof deck and wrap it in metal flashing, or buy a prefabricated curb made for your specific panel profile. Prefab metal curbs cost more but come with the rib pattern already formed and a welded or soldered cricket on the uphill side.
Standing-seam roofs
Size the skylight so it fits between two seams whenever possible. Cutting through a seam complicates the flashing and weakens the panel lock. Common panel widths run 12 to 18 inches, so a narrow skylight may fit within one or two pans. Wider units require removing or cutting a seam and reforming the panels around the curb, which is often a job for a metal roofing crew.
Exposed-fastener panels
On corrugated, R-panel, or similar through-fastened roofs, choose a curb with a flange that matches your rib height and spacing. Even a quarter inch mismatch leaves gaps that sealant cannot reliably bridge. Take a profile sample or detailed measurements when ordering.
Glazing and sizing
Low-E, laminated or tempered glazing controls heat gain and adds safety. Check that the skylight’s rough opening fits between your rafters or trusses, or plan to add headers. Never cut a truss chord without an engineer’s approval.
Tools and Materials
- Curb mount skylight sized to the rafter bay
- Prefabricated metal curb, or lumber and sheet metal to build and wrap one
- Uphill diverter or cricket
- Butyl tape sealant and a compatible polyurethane or polyether sealant rated for metal roofing
- Stitch screws and gasketed roofing screws, matched to your panel
- Self-adhered ice and water membrane
- Metal-cutting shears, nibbler, or a metal-cutting circular saw blade (avoid abrasive discs, which burn the coating)
- Reciprocating saw for the deck opening, framing lumber for headers
- Roof anchors, harness, and a secured ladder
Step-by-Step Installation
1. Plan from inside the attic
Locate the rafters or trusses and mark the opening from below. Drive a nail up through each corner so you can find the layout on the roof. Confirm no wiring, ducts, or plumbing vents sit in the path.
2. Set up fall protection
Metal roofs are slick, especially with dew, dust, or frost. Wear soft-soled shoes, use a roof anchor and harness, and never work on a wet panel. Details are covered in the safety section.
3. Cut the panel and deck
Mark the opening on the panel, then cut the metal with shears or a nibbler. Keep hot metal filings off the finish; they rust and stain. Cut the deck beneath with a reciprocating saw, and frame the opening with headers and trimmers tied into the rafters.
4. Membrane the opening
Wrap the deck edges with self-adhered membrane, lapping it up the curb sides. On standing-seam roofs, many installers slide a membrane collar under the panels around the opening as a secondary barrier.
5. Install the curb
For exposed-fastener roofs, apply butyl tape along the underside of the curb flange following the rib profile, set the curb, and fasten through the flats with gasketed screws at tight spacing. Never put a fastener through the high ribs on the uphill side where water concentrates. For standing-seam roofs, the curb flanges typically slide under the upslope panel and over the downslope panel, with the side flanges turned up and sealed against the seams, so the panels can still move.
6. Add the diverter
The diverter or cricket on the uphill side is the single most important piece. It splits the water and pushes it into the pans beside the curb. Seal it with butyl on the underside and make sure it overlaps the curb head flashing in the direction of water flow.
7. Set the skylight
Place the skylight on the curb with the gaskets or sealant the manufacturer specifies, and fasten per the instructions. Check that weep holes are clear so condensation can escape.
8. Seal and inspect
Tool all sealant lines, check every fastener for a snug but not crushed washer, and run a garden hose over the roof from above the skylight, starting low and working up. Have a helper watch the attic side for drips.
9. Finish the interior
Frame and drywall the light shaft, insulate the shaft walls to the same level as the attic, and add a vapor retarder where your climate requires one. A well-insulated shaft reduces condensation on the glass.
Troubleshooting Leaks
Drip at the uphill corner: Usually a diverter that does not fully shed water or a sealant gap where the cricket meets the curb. Clean and reseal, or replace with a larger cricket.
Water in the pans below the curb: The downhill flange may lap under the panel instead of over it. Water must always flow from upper pieces onto lower pieces.
Leaks only in cold weather: Often condensation rather than a roof leak. Check shaft insulation and attic ventilation, and consider a skylight with better insulated glazing.
Squeaks, oil canning, or cracked sealant: The curb is pinning a standing-seam panel. The connection may need to be redesigned to allow movement.
Cost Ranges
The skylight itself runs from a few hundred dollars for a basic fixed unit to well over a thousand for venting or larger models. Prefabricated metal curbs matched to a panel profile typically add a few hundred to around a thousand dollars. Professional installation for skylights in metal roofs commonly lands in the low thousands to several thousand dollars total, depending on roof type, pitch, whether seams must be reformed, and interior shaft finishing. Standing-seam jobs usually cost more than exposed-fastener jobs.
Safety: Ladders, Falls and Structure
Falls from roofs are among the most serious home improvement injuries. Set your extension ladder on firm, level ground at about a 4 to 1 angle, extend it 3 feet past the eave, and tie it off at the top. Wear a harness clipped to a properly installed roof anchor. Metal panels are slippery, so avoid working in wind, rain, dew, or frost. For any roof on a two-story home or steeper than about 6 in 12, hire a pro with scaffolding and fall protection.
Structurally, the opening must be properly framed. Cutting a rafter requires headers carrying the load to adjacent rafters, and trusses should not be cut without an engineered repair. Many jurisdictions require a permit for new roof openings, and HOAs may restrict visible changes.
When to Call a Pro
Call a metal roofing contractor if you have a standing-seam roof that requires cutting a seam, a low-slope roof, a roof still under a panel warranty, or trusses in the way. A pro can fabricate custom curbs, reform panels, and keep the roof warranty intact. Framing modifications to trusses need an engineer. And if you are uncomfortable working at height, a pro install is worth every dollar.
Frequently Asked Questions
Can you put a skylight in a metal roof?
Yes. Use a curb mount skylight with a curb matched to your panel profile, an uphill diverter, and sealants made for metal. Shingle flashing kits are not suitable.
Do skylights in metal roofs leak more often?
Not when installed correctly. Most leaks trace back to a missing or undersized diverter, a mismatched curb flange, or fasteners through high ribs on the uphill side.
What is a diverter on a skylight curb?
A diverter or cricket is a peaked piece of metal on the uphill side of the curb that splits the flow of water and sends it around the skylight into neighboring pans.
Can I install a skylight on a standing-seam roof myself?
It is possible for small skylights that fit between seams, but cutting seams or reforming panels usually requires a metal roofing contractor to preserve the roof’s watertightness and warranty.
How much does a skylight in a metal roof cost?
Expect the unit plus curb to run from several hundred to over a thousand dollars, and professional installation to total in the low thousands to several thousand depending on roof type and finishing.