Home Improvement

Mobile Home Flex Duct: Replacing the Crossover and Oval Ducts

Mobile Home Flex Duct: Replacing the Crossover and Oval Ducts

If one half of your double-wide feels ten degrees colder than the other, the culprit is usually not the furnace. It is the mobile home flex duct that crosses under the home from one section to the other, lying in the dirt, crushed, torn or chewed open by animals. That single crossover run carries roughly half of your heated or cooled air, so when it fails you pay to condition the crawlspace instead of the bedrooms.

The fix is usually straightforward. You remove the damaged crossover, install a new insulated flexible duct of the correct diameter, clamp and seal it to the collars on each section’s trunk, and hang it so it never touches the ground. Where clearance is tight, an oval flexible duct can replace round flex without crushing. Most homeowners can do the job in an afternoon with basic tools, as long as the furnace is shut down first and the work stays on the duct side rather than the furnace or its venting.

Here is how manufactured home duct systems are laid out, how to pick between round and oval flex, the step-by-step replacement process, and when the problem points to something a licensed HVAC technician should handle.

How Mobile Home Flex Duct Fits Into the Duct System

Manufactured homes use a different layout from site-built houses. Instead of a basement plenum feeding branch runs, most homes have a long sheet metal trunk running down the center of each section, sealed inside the belly (the underside wrapped in a fabric or plastic bottom board). The furnace sits in a closet and blows down into that trunk. Floor registers cut directly into the top of the trunk deliver air to each room.

In a single-wide, the trunk does the whole job. In a double-wide or triple-wide, the furnace sits in one section, so air must travel to the other. That is the role of the crossover duct, sometimes called the mobile home crossover duct. It connects a collar on the bottom of one trunk to a collar on the other, passing underneath the marriage line where the two halves join.

Mobile home flex duct appears in two places:

  • The crossover: almost always an insulated round flex duct, typically 12 to 16 inches in diameter, running in a shallow U or a straight span under the home.
  • Branch or replacement runs: where a section of metal trunk has rusted out, or where a duct must pass through a tight floor cavity, oval flex or flexible oval ductwork is sometimes used because it keeps more airflow in a shorter height.

Some homes also have a second crossover for the return air, or for an add-on air conditioner or heat pump. Check under the home before you buy materials so you know how many runs you are replacing.

Signs the Crossover Duct Needs Replacing

Crossovers live in a rough environment: humidity, temperature swings, rodents, pets and the occasional contractor who steps on them. Common warning signs include:

  • One section of the home is much warmer or cooler than the other.
  • Weak airflow at registers on the far side from the furnace.
  • Visible tears in the outer jacket, or insulation hanging loose.
  • The duct is lying on the ground, sitting in standing water, or flattened.
  • Condensation or mold on the outer jacket during cooling season.
  • Higher energy bills with no change in thermostat habits.
  • A musty or earthy smell when the system runs, which suggests the duct is pulling crawlspace air.

A quick check: with the blower running, hold your hand near the collar connections. Air rushing out means the seal has failed. If the inner liner is torn, you will often hear a whistle or feel air through the jacket itself.

Oval vs Round Flex Duct

Round insulated flex is the default for crossovers because it moves air efficiently and is easy to find in standard diameters. Oval flexible duct is a flattened version designed to fit where a round duct would need too much depth. It is common in manufactured home floor systems and in some retrofit situations under homes with very low skirting clearance.

Factor Round flex Oval flex
Airflow per size Highest for the material used Slightly lower; size up
Height needed Full diameter Roughly half to two thirds
Availability Any supply house Specialty or manufactured home suppliers
Best use Standard crossovers Tight belly or low-clearance runs

Oval flex duct must match the collar shape or be paired with a proper transition. Do not squeeze a round duct into an oval opening, and do not crush round flex into an oval shape to make it fit. Flattening a round duct cuts airflow sharply and stresses the liner. If you are matching an original oval run, measure both the long and short dimensions of the collar before ordering.

Choosing the Right Diameter

Match the existing collar size. Most crossovers are 12, 14 or 16 inches. Going smaller to save money starves the far section of air. Going larger than the collar means a reducer, which adds turbulence. If the old duct is missing and you have no collar to measure, ask an HVAC supplier or the home’s manufacturer for the original spec, which is often on the data plate or in the installation manual.

Insulation Value

Crossovers run outside the conditioned space, so insulation matters. Look for flex rated at R-8 for most climates. In very cold regions, some owners choose higher-rated duct where available. A vapor barrier jacket that stays intact keeps moisture from condensing in the insulation during summer cooling.

Tools and Materials

  • Insulated flex duct (round or oval) in the correct size and length, plus about 2 feet of extra
  • Large stainless steel worm-drive clamps or heavy nylon duct straps sized for the collar
  • UL 181-listed foil tape and duct mastic
  • Duct support straps, at least 1.5 inches wide, or a plastic or metal cradle
  • Galvanized strapping, screws or concrete blocks for support points
  • Utility knife, tin snips, screwdriver or nut driver
  • Work gloves, safety glasses, a dust mask or respirator (fiberglass and crawlspace dust)
  • Headlamp, knee pads and a crawl mat or tarp
  • Optional: a manufactured home crossover duct kit with collars, clamps and supports included

Many suppliers sell a complete mobile home crossover duct kit. For homeowners replacing a single crossover, a kit simplifies matching clamps and collars, and it typically costs only a little more than buying parts separately.

Step-by-Step: Replacing a Crossover Duct

  1. Shut down the system. Set the thermostat to off and turn off power to the furnace at its service switch or breaker. You are working on ductwork, not the burner, but the blower should not start while your hands are near a collar.
  2. Locate both collars. Open the skirting access panel and find the crossover. Follow it to each section. The collars drop down a few inches through the belly fabric.
  3. Remove the old duct. Cut or loosen the clamps or straps. Peel back the outer jacket and insulation, then release the inner liner from the collar. Bag the old duct; it often contains rodent debris, so wear a respirator.
  4. Inspect the collars. Look for rust, loose screws or gaps where the collar meets the trunk. Seal any gaps with mastic. If the collar is rusted through or the belly around it is torn, patch the belly with belly-board material and tape before reconnecting.
  5. Measure and cut the new duct. Stretch the flex fully, then cut it to a length that reaches both collars with gentle curves and no sag. Excess length causes droops that collect condensation and choke airflow. Cut the liner with a knife and the wire helix with snips.
  6. Attach the inner liner. Slide the liner at least 2 inches over the first collar. Wrap the joint with two layers of foil tape, then secure it with a clamp or strap tightened firmly. Repeat on the other side.
  7. Pull the insulation and jacket over. Draw the insulation and outer jacket up over the joint so the collar is fully covered. Secure the jacket with a second strap and tape the seam so it is vapor tight.
  8. Support the duct off the ground. Hang the duct from the home’s frame or the floor joists with wide straps every 4 to 5 feet, or set it in a cradle. The duct should never touch soil or sit where water collects. Avoid narrow wire, which cuts into the insulation.
  9. Restore power and test. Turn the furnace back on and run the blower. Feel the collars for leaks and check airflow at the far registers. Re-tape any spot where you feel air escaping.
  10. Close up the skirting. Replace the access panel and make sure skirting vents are open where required for crawlspace ventilation.
Looking to buy Mobile Home Flex Duct? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Sealing Mobile Home Flex Duct to the Trunk

Most efficiency loss in a mobile home flex duct system happens at the connections, not along the run. Foil tape alone tends to lose adhesion over time in a damp crawlspace. The more durable approach is mastic on the collar seams and the trunk joint, followed by a mechanical clamp on the liner, with tape added as a secondary seal.

Never use plain cloth duct tape. It dries out and releases within a season or two. Also avoid running screws through the flex liner, which creates leaks. If the trunk itself has leaks at register boots or end caps, sealing those from inside the home with mastic at each register opening can improve airflow noticeably.

Furnace and Combustion Safety

Duct work often turns into a look at the furnace itself. Keep the two jobs separate. Replacing the crossover is a reasonable DIY task, but anything involving the burner, gas line, venting or heat exchanger belongs to a licensed HVAC technician.

  • Install carbon monoxide alarms on every level and near each sleeping area. Manufactured homes are compact, so even a small vent leak can matter.
  • Manufactured home furnaces are sealed-combustion units that draw outdoor air and vent through the roof. Never block the roof jack or the combustion air intake, and keep the furnace closet door closed if it is designed to be closed.
  • Do not alter the vent pipe, combustion air ducts or burner area while working on ductwork.
  • Have the furnace and venting inspected annually, ideally before the heating season.
  • If you smell gas, leave the home and call your gas utility from outside. Do not operate switches.
  • Never use an unvented fuel-burning space heater indoors unless the label specifically permits it, and follow its instructions.

A crushed or disconnected crossover can also change how the furnace behaves. Restricted airflow makes the heat exchanger run hotter, which can trip the high-limit switch or shorten the furnace’s life. Restoring proper airflow is one reason crossover repairs pay off quickly.

Troubleshooting After Replacement

  • Far side still weak: Check that dampers on the trunk are open, that the duct is not kinked, and that registers are not blocked by furniture or rugs. A crushed section of metal trunk can also restrict flow.
  • Whistling or rattling: Usually a loose collar or a liner that is not fully over the collar. Re-clamp.
  • Condensation on the jacket: The vapor barrier is torn or the seam is open. Tape it. Sweating can also mean the duct is too close to wet ground.
  • Furnace cycles off quickly: Possible airflow restriction or dirty filter. Replace the filter; if short cycling continues, call a technician.
  • Rodents return: Seal gaps in the skirting with hardware cloth and keep the duct off the ground where animals nest.

Cost to Replace Mobile Home Ductwork

A DIY crossover replacement usually costs a modest amount for materials, often in the range of a few dozen dollars to around a couple hundred depending on diameter, length and whether you buy a kit. Oval flexible duct costs more per foot than round and may need to be ordered from a manufactured home supply store.

Hiring a contractor to replace the crossover typically runs a few hundred dollars, more if access is difficult or the collars need repair. Replacing sections of the metal trunk, repairing large belly tears or replacing the whole duct system is a larger job that can reach into the low thousands. Get at least two quotes, and ask whether belly repair and sealing are included.

When to Call a Professional

Call an HVAC technician experienced with manufactured homes if the metal trunk is rusted through, if multiple registers have little airflow even after the crossover is fixed, if you see soot, scorch marks or water around the furnace, or if a carbon monoxide alarm sounds. Gas lines, burner adjustments and vent work always need a licensed pro and, in many areas, a permit. Crawlspaces with standing water, heavy mold or significant animal infestation are also worth handing off.

Frequently Asked Questions

What size is a mobile home crossover duct?

Most crossovers are 12, 14 or 16 inches in diameter. Measure the collar on the bottom of the trunk and match it exactly rather than guessing from the old duct, which may have stretched.

Can I use oval flex duct instead of round?

Yes, where clearance is tight, as long as the oval duct is sized to carry similar airflow and connects to a matching collar or a proper transition. Do not flatten round flex to make it fit.

Should the crossover duct touch the ground?

No. A duct lying on soil collects moisture, attracts pests and gets crushed. Support it with wide straps or a cradle every 4 to 5 feet so it stays clear of the ground.

How long does mobile home flex duct last?

A well-supported, intact crossover often lasts 10 to 15 years or more. Ducts on the ground, exposed to pets or rodents, or in very wet crawlspaces can fail in a few years.

Is it safe to replace the crossover duct myself?

For most homeowners, yes. Turn off the furnace, wear gloves and a respirator, and keep your work on the duct side. Leave the furnace, gas line and venting to a licensed technician.