Walk into the fastener aisle and ask for a “16-penny nail” and you will get a 3-1/2 inch nail, even though nothing on the box says sixteen of anything costs a penny anymore. A good nail size chart translates that old penny system (written with a “d”) into the numbers that actually matter on the job: length, shank diameter and how many nails you get per pound. Once you can read those three columns, picking the right nail for framing, sheathing, trim or decking takes seconds instead of guesswork.
The short version: penny size tells you length, and length goes up by 1/4 inch per penny from 2d through 10d, then in bigger jumps. Common nails have the thickest shanks for structural work, box nails are thinner to reduce splitting, and finish nails are thin with small heads so they can be set and hidden. Match the nail to the job, the wood and any fastening schedule your local building code or plans call for.
- Nail Size Chart: Penny Size to Length and Diameter
- Where the Penny System Came From and Why It Stuck
- Common vs Box vs Sinker vs Finish Nails
- Which Nail Size to Use for Common Jobs
- Reading Nail Boxes and Collated Strips
- Step by Step: Choosing a Nail for Any Project
- Troubleshooting Nail Problems
- Typical Nail Costs
- When to Call a Pro
- Frequently Asked Questions
Nail Size Chart: Penny Size to Length and Diameter
The figures here are typical values for bright steel common nails. Different makers vary by a few thousandths of an inch, and coated or collated nails often run slightly thinner, so check the box when a plan specifies a diameter.
| Penny size | Length | Common nail shank (approx.) | Nails per lb (approx.) |
|---|---|---|---|
| 2d | 1 in | 0.072 in (15 gauge) | 850 |
| 3d | 1-1/4 in | 0.080 in (14 gauge) | 540 |
| 4d | 1-1/2 in | 0.098 in (12.5 gauge) | 290 |
| 5d | 1-3/4 in | 0.098 in (12.5 gauge) | 250 |
| 6d | 2 in | 0.113 in (11.5 gauge) | 165 |
| 8d | 2-1/2 in | 0.131 in (10.25 gauge) | 100 |
| 10d | 3 in | 0.148 in (9 gauge) | 65 |
| 12d | 3-1/4 in | 0.148 in (9 gauge) | 60 |
| 16d | 3-1/2 in | 0.162 in (8 gauge) | 45 |
| 20d | 4 in | 0.192 in (6 gauge) | 30 |
| 30d | 4-1/2 in | 0.207 in (5 gauge) | 20 |
| 40d | 5 in | 0.225 in (4 gauge) | 17 |
| 60d | 6 in | 0.263 in (2 gauge) | 11 |
Two patterns stand out. First, length climbs by a quarter inch per penny up to 10d (3 inches), so you can do the math in your head: subtract 2 from the penny number, divide by 4, and add 1 inch. Second, the gauge number drops as the nail gets thicker, which trips people up the first time. A 6 gauge nail is much heavier than a 15 gauge nail. That same logic carries over to nail gun gauges for trim work, which is a separate system worth learning on its own.
Where the Penny System Came From and Why It Stuck
The “d” comes from the Roman denarius, the coin abbreviation used in old English currency. Centuries ago, nails were sold by the hundred, and the price of a hundred nails gave each size its name. Prices changed long ago, but the names became a de facto standard, and American framing plans, lumberyards and building codes still use them.
That is why a modern nail length chart or penny chart still lists sizes like 8d and 16d instead of simple inches. If you are reading a plan set or a structural fastening schedule, the penny size is what you will see, and it usually implies a common nail unless the drawing says box, sinker or a specific diameter.
Common vs Box vs Sinker vs Finish Nails
Penny size controls length, but the nail type controls diameter and head style. A 16d common and a 16d box nail are the same length with very different holding power.
Common nails
Thick shank, broad flat head, built for structural framing. A 16d common at roughly 0.162 inch is the classic choice for nailing 2×4 plates and face nailing doubled studs. The extra steel resists bending and gives the most shear strength per nail.
Box nails
Same lengths as common nails but a thinner shank, for example about 0.113 inch for an 8d box versus 0.131 inch for an 8d common. They split thin or dry lumber less often, which is why they were popular for siding and light framing. They are not a direct substitute for common nails when a plan calls for a specific structural fastener.
Sinkers
Sinkers are slightly shorter and thinner than commons (a 16d sinker is about 3-1/4 inches long and 0.148 inch thick), with a coated shank and a countersunk head. Many framing crews use them because they drive easily and the coating improves withdrawal resistance. A lot of framing nailer nails sold as “16d” are actually sinker or reduced-diameter sizes, so read the label.
Finish and casing nails
These have small heads so you can set them beneath the surface and fill the hole. Finish nails are the thinnest; casing nails are slightly heavier with a tapered head for door and window casing. Typical trim sizes run 4d to 8d. A 6d finish nail (2 inches) is a common pick for baseboard into studs, and 8d (2-1/2 inches) works for thicker casing.
Which Nail Size to Use for Common Jobs
The quickest rule of thumb is that a nail should be about three times the thickness of the board you are fastening, so two-thirds of its length ends up in the piece you are nailing into. Use that as a starting point, then follow your local code or the fastening schedule on your plans for anything structural.
- Wall framing (end nailing studs to plates): 16d common or 16d sinker, two per joint.
- Face nailing doubled studs or headers: 10d or 16d, staggered roughly every 12 to 24 inches as specified.
- Toenailing studs: 8d common, usually three or four per joint, or 16d where allowed.
- Wall and roof sheathing (7/16 to 5/8 inch panels): 8d common or ring-shank, spaced per the plan (often 6 inches at edges and 12 inches in the field).
- Subfloor (3/4 inch plywood or OSB): 8d ring-shank or 10d, or screws plus construction adhesive to reduce squeaks.
- Exterior decking (5/4 or 2x boards): 10d or 16d hot-dipped galvanized or stainless ring-shank, or deck screws.
- Baseboard and casing: 6d or 8d finish nails, or 15 to 18 gauge gun nails long enough to reach the framing.
- Cedar or redwood siding: stainless or hot-dipped galvanized siding nails long enough to penetrate framing about 1-1/4 inches.
Pressure-treated lumber needs hot-dipped galvanized (look for a heavy zinc coating) or stainless nails. Modern treatment chemicals corrode plain steel and electro-galvanized nails quickly, which shows up as rust streaks and loose boards within a few seasons.
Reading Nail Boxes and Collated Strips
When you shop, the box will usually list three things: penny size, length and shank diameter. For hand nailing, that is all you need. For a framing nailer, you also need to match the collation angle (often 21, 28 or 30 to 34 degrees), the head type (full round or clipped) and the diameter range the tool accepts.
A framing nailer makes repetitive framing and sheathing much faster, and most handle nails from 2 to 3-1/2 inches. Just remember that “16d” on a strip of gun nails might mean 3-1/4 inches by 0.131 inch, not the full 3-1/2 by 0.162 inch common nail in a hand-nailing nail size guide. Some building departments accept the thinner nails at closer spacing; check before you swap.
Shank styles
- Smooth shank: standard framing, easiest to remove if you make a mistake.
- Ring shank: annular rings lock into wood fibers; best for subfloors, decking and siding where withdrawal matters.
- Spiral (screw) shank: twists as it drives; good for hardwood flooring and pallets.
- Coated (vinyl or cement): lubricates on the way in, then grips as the coating sets.
Step by Step: Choosing a Nail for Any Project
- Measure the material you are fastening. A 3/4 inch board needs roughly a 2 to 2-1/4 inch nail; a 1-1/2 inch 2x board needs about 3 to 3-1/2 inches.
- Pick the nail type. Common or sinker for structure, box for thin or split-prone wood, finish or casing for visible trim.
- Choose the finish. Bright for interior dry framing, hot-dipped galvanized or stainless for exterior and treated lumber.
- Check the shank. Ring or spiral when boards will see foot traffic, vibration or seasonal movement.
- Confirm code or plan requirements. Structural connections, shear walls and roof sheathing often have specified sizes and spacing.
- Test on a scrap. Drive two or three nails near an end. If the wood splits, step down a size, blunt the tip with a hammer tap, or pre-drill.
Troubleshooting Nail Problems
Boards splitting at the ends: the shank is too thick or the nail is too close to the edge. Move in at least 3/4 inch, switch to a box nail or pre-drill a hole slightly smaller than the shank.
Nails bending: common in dense hardwoods and old dry lumber. Use a heavier hammer, hit squarely, or pre-drill. A spiral-shank nail often drives straighter.
Nails backing out (nail pops): the wood shrank or the nail was too short. Ring-shank nails or screws cure most of this in subfloors and decking.
Rust stains on exterior trim: the nails were not rated for outdoor use. Replace with stainless or hot-dipped galvanized and touch up the finish.
Points poking through: nail too long for the stack-up. Subtract a size, or angle the nail slightly.
Typical Nail Costs
Nails are inexpensive compared with screws. Bright common nails in 1 to 5 pound boxes usually run a few dollars per pound. Hot-dipped galvanized nails cost noticeably more, and stainless steel can cost several times as much as bright steel, which is still worth it for cedar, redwood and coastal decks. Collated framing nails are sold in boxes of a few thousand and typically range from the mid-tens to well over a hundred dollars depending on finish and length.
If you are framing a shed or a small wall, buying one bulk box of the right size is cheaper than several small packs. Keep a spare pound of 8d and 16d on hand; they cover a surprising share of household repairs.
When to Call a Pro
Swapping a trim nail or building a bookshelf is easy DIY work. Structural changes are different: load-bearing walls, headers, deck ledgers, roof framing and shear walls often require permits, inspections and specific fastener schedules. A licensed contractor or structural engineer can confirm the right nails, spacing and connectors so the work passes inspection and holds up for decades. Keep the nail size chart handy for everything else.
Frequently Asked Questions
What does the “d” mean in nail sizes?
The “d” stands for penny, from the Roman coin denarius. It once described the price of 100 nails and now simply indicates length, such as 8d for 2-1/2 inches and 16d for 3-1/2 inches.
What size nail is used for 2×4 framing?
16d common or 16d sinker nails are standard for end nailing studs through plates, with 8d or 10d often used for toenailing. Always follow the fastening schedule your local code or plans require.
Is a 16d nail the same as a 3-1/2 inch nail?
A 16d common nail is 3-1/2 inches long. A 16d sinker is about 3-1/4 inches, and many collated gun nails labeled 16d are shorter or thinner, so check the box for actual length and diameter.
Can I use box nails instead of common nails?
For non-structural work, yes. Box nails are thinner and split wood less, but they hold less in shear, so do not substitute them where a plan or code specifies common nails.
What nail size should I use for baseboard?
A 6d or 8d finish nail, or a 15 to 18 gauge gun nail, long enough to pass through the trim and drywall and reach about 3/4 to 1 inch into the studs or plate.