Home Improvement

Plumb a Double Vanity: Drains, Vents and Supply Lines

Plumb a Double Vanity: Drains, Vents and Supply Lines

Swapping a single sink for two is one of the most requested bathroom upgrades, and it is also where a lot of weekend projects stall. To plumb a double vanity, you need to decide how two sinks will share (or not share) a drain, confirm that the drain is properly vented, and split or extend the hot and cold supplies so each faucet gets steady pressure. None of these steps is exotic, but each one has to be right, because a slow drain or a sewer-gas smell is hard to fix once the countertop is set.

The quick answer for most homes: if the two sink drains will sit within a few feet of each other and your existing drain line is at least 1-1/2 inches, a continuous waste kit that joins both tailpieces into a single trap is usually the simplest and most code-friendly route. If the sinks are spread wide apart, or the vanity is 72 inches or longer, running a separate trap arm for each sink into a new sanitary tee often drains better and keeps venting straightforward. Supply lines are easier. You either tee off the existing stub-outs or open the wall and add a second set of shutoff valves.

This guide walks through the decision between shared and separate drains, the parts list, the step-by-step double vanity install, common problems, typical costs, and the point where a licensed plumber should take over.

How to Plumb a Double Vanity: Shared vs Separate Drains

Every drain layout for two sinks falls into one of two camps. Knowing which one fits your wall saves you from buying the wrong fittings.

Option 1: One trap with a continuous waste kit

A continuous waste kit, often sold as a double sink drain kit, connects the tailpiece of each sink with horizontal pipe and a tee (end outlet or center outlet), then feeds a single P-trap. The trap connects to the existing trap arm in the wall. This works well when the two drains sit roughly 30 to 40 inches apart and the wall drain lands between them. It avoids opening the wall, which is the main reason homeowners choose it.

The limitations are real, though. The horizontal run from the far sink to the tee needs a slight downward slope, typically about 1/4 inch per foot, and the tailpiece of the farther sink cannot be so long that the water drops a long vertical distance before entering the trap. Many local codes also cap the distance between the two outlets. If the kit has to stretch across a 60-inch or 72-inch vanity, you are pushing the design.

Option 2: Separate traps into a double fixture fitting

For wider vanities, each sink gets its own P-trap and trap arm. The two arms tie into the drain stack either through two sanitary tees at slightly different heights or through a double sanitary tee (sometimes called a double fixture fitting) centered between the sinks. This requires opening the drywall behind the vanity and extending or rerouting the drain, but it gives each sink a short, well-vented path and the best flow.

Quick decision guide

  • Vanity 48 to 60 inches, wall drain centered, sinks close together: continuous waste kit with a center-outlet tee.
  • Vanity 60 to 72 inches with sinks near each end: separate traps into a double fixture fitting behind the wall.
  • Existing drain smaller than 1-1/2 inches or visibly corroded: replace the section and plan separate arms.
  • Drain stub-out far off to one side: expect to open the wall and relocate it regardless of layout.

Venting: The Part Most DIY Jobs Get Wrong

A trap only works if air can enter the drain system behind it. Without a vent, water rushing down the pipe siphons the trap dry, and sewer gas comes up through the sink. With a continuous waste kit, both sinks share one trap and one vent, so if your existing single sink was properly vented, the shared layout usually keeps that vent in play.

Separate traps are a different story. Each trap arm has a maximum length to its vent that depends on pipe size; for 1-1/2 inch pipe that distance is commonly around 6 feet, but your local code sets the exact figure. A double fixture fitting on a vertical stack that continues up as a vent handles both arms neatly. Where running a new vent through the wall and attic is impractical, some jurisdictions allow an air admittance valve (a one-way mechanical vent) installed in an accessible spot under the vanity. Others do not permit them at all, so check with your building department before relying on one.

Signs of a venting problem include gurgling when the other sink drains, slow drainage that no snake fixes, and a faint sewer odor after a bath empties. Those symptoms point to a design issue rather than a clog.

Splitting Supply Lines for Two Faucets

Water supply is the easier half of the job. You have three common options, listed from least to most invasive:

  1. Tee under the vanity. Replace each existing shutoff valve with a dual-outlet (two-way) stop, or add a brass tee after the valve, then run braided supply lines to each faucet. This is quick, but one valve now controls both sinks, and long supply runs across the cabinet can look messy.
  2. Extend inside the wall. Open the drywall, cut in tees on the hot and cold lines, and add new stub-outs with individual quarter-turn stops at each sink location. Each faucet gets its own shutoff, which is how most new construction is plumbed.
  3. Home run from a manifold. In homes with PEX manifolds, a new line can run from the manifold to the second sink. It gives the best pressure balance but requires fishing new lines through framing.

Keep hot on the left, cold on the right at every faucet. If the second sink sits far from the water heater, expect a short wait for hot water; that is normal and not a sign of a leak.

Spacing and Layout Rules to Check

Codes and manufacturer instructions set minimum clearances. A common baseline is at least 15 inches from the center of each sink to a side wall or obstruction and roughly 30 inches center to center between sinks, which is why 60 inches is the practical minimum vanity width for two full-size basins. Some jurisdictions use slightly different numbers, so confirm locally.

Also measure the drain height. Wall drain stub-outs for vanities typically land 16 to 20 inches above the finished floor, and the trap must sit below the sink tailpiece with enough room to slope the trap arm back to the wall. Vessel sinks and vanities with drawers wrapped around the plumbing change this math, so read the vanity’s rough-in sheet before you cut anything.

Tools and Materials

  • Double sink drain kit (continuous waste kit) or two P-traps plus a double fixture fitting
  • PVC or ABS pipe and fittings sized to match the existing drain, plus primer and cement appropriate to the material
  • Dual-outlet shutoff valves or tees, new quarter-turn stops, and braided supply lines
  • Tubing cutter, hacksaw or PVC cutter, deburring tool
  • Adjustable wrenches, channel-lock pliers, and a basin wrench
  • Level, tape measure, stud finder, and a drywall saw
  • Plumber’s putty or silicone for drain flanges, thread seal tape
  • Bucket, towels, flashlight, and safety glasses
Looking to buy Plumb a Double Vanity? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Step-by-Step Double Vanity Install

  1. Shut off the water and relieve pressure. Close the main or the fixture shutoffs, then open a faucet at a lower level to drain the lines. Place a bucket under the trap before loosening anything.
  2. Remove the old vanity. Disconnect supplies and the trap, cut any caulk at the wall, and pull the cabinet. Plug the open drain with a rag or test cap to block sewer gas.
  3. Mark the new layout. Set the new vanity in place, mark each sink centerline on the wall, and confirm where the drain and supplies need to land using the rough-in sheet.
  4. Modify the drain. For a continuous waste kit, confirm the existing stub-out lines up with the kit’s tee. For separate traps, open the wall, cut out the old sanitary tee, and install the double fixture fitting or two tees with new stub-outs. Maintain 1/4 inch per foot slope on every horizontal run.
  5. Extend supply lines if needed. Cut in tees on the hot and cold lines, run new stubs to each sink location, and secure them to blocking so they do not move when valves turn.
  6. Pressure-test before closing the wall. Turn the water back on and check every new joint for weeping. Leave the wall open for a few hours if you can.
  7. Set the vanity and top. Anchor the cabinet to studs, level it, and install the countertop and sinks per the manufacturer’s instructions.
  8. Install faucets and drains. Mount each faucet and pop-up drain before connecting supplies. Seal drain flanges with putty or silicone as the sink maker specifies.
  9. Connect the drain assembly. Dry-fit the continuous waste kit or both traps, trim tailpieces to length, then hand-tighten slip nuts plus a quarter turn with pliers. Overtightening cracks plastic nuts.
  10. Connect supplies and test. Attach braided lines, open the stops slowly, fill both basins, and pull both stoppers at once. Watch every joint with a flashlight and a dry paper towel.

Troubleshooting Common Problems

  • One sink drains slowly, the other is fine: the continuous waste run from the far sink may be sloped wrong or too long. Re-slope it or switch to separate traps.
  • Gurgling when the other sink empties: classic venting issue. The trap is being partially siphoned; the fix is a proper vent or a code-approved air admittance valve.
  • Drips at slip joints: washers are reversed or the pipe is cut out of square. Recut, deburr, and reseat.
  • Low pressure at one faucet: a kinked braided line, a partly closed stop, or a clogged aerator. Check the aerator first.
  • Sewer smell: a dry trap, a missing vent, or a loose connection behind the wall. Run water in both sinks, then investigate venting if the odor returns.

What It Costs

If the existing plumbing lines up with a continuous waste kit and you tee the supplies under the cabinet, parts often stay under a hundred dollars and the plumbing takes an afternoon. Opening the wall to add a double fixture fitting, new vent work, and separate supply stubs pushes the job into a full day or more. Hiring a plumber for that level of rough-in commonly runs from several hundred dollars to over a thousand, depending on access, pipe material, and whether a vent has to go through the roof. Drywall patching, tile repair, and the vanity itself are separate costs.

When to Call a Licensed Professional

Swapping a vanity on existing rough-in is within reach for a handy homeowner. Moving drains, adding vents, cutting into a main stack, or working with cast iron or galvanized pipe is a different level, and most jurisdictions require a permit for new drain or vent work. A licensed plumber knows local trap-arm limits, vent rules, and whether air admittance valves are allowed, and a permitted, inspected job protects you at resale. Call a pro if the drain stack is inside an exterior wall, if you find corroded or undersized pipe, or if you are not sure your house has a proper vent at all.

If the project also involves moving a light fixture or adding outlets near the new sinks, that work belongs to a licensed electrician. Bathroom receptacles must be GFCI-protected, and any electrical work starts by turning off the breaker and confirming power is off with a non-contact voltage tester.

Frequently Asked Questions

Can two bathroom sinks share one drain?

Yes. A continuous waste kit joins both sink tailpieces into a single P-trap that connects to one drain line. It works best when the sinks are close together and the drain is centered between them. Wide vanities often drain better with separate traps.

Does a double vanity need two vents?

Not always. When both sinks share one trap, a single vent serves the fixture. With separate traps, each trap arm must be within the allowed distance of a vent, which a double fixture fitting on a vented stack can satisfy with one vertical vent.

What size drain do I need for two sinks?

A 1-1/2 inch drain line is standard for a double lavatory in most codes, though some jurisdictions or long runs call for 2 inches. Match what your local code and the existing stack require.

How far apart should double vanity sinks be?

A common guideline is about 30 inches center to center, with at least 15 inches from each sink’s center to a side wall. That makes 60 inches the practical minimum vanity width for two sinks.

Do I need a permit to plumb a double vanity?

Replacing a vanity on existing plumbing usually does not need one. Adding or relocating drains, vents, or supply lines inside the wall typically does. Call your building department before you open the wall.