Home Improvement

Kohler Bellwether Bathtub: Cast Iron Sizes, Weight & Specs

Kohler Bellwether Bathtub: Cast Iron Sizes, Weight & Specs

A Kohler Bellwether bathtub weighs about as much as a refrigerator before you add a drop of water, and that single fact shapes almost every decision about buying and installing one. Bellwether is Kohler’s enameled cast iron alcove bath line, built for standard three-wall tub openings, with clean square lines, wide ledges, an integral apron and a slip-resistant bottom. It comes in a standard 60-inch length and a longer 66-inch soaking version.

The quick answer for most remodels: the 60 x 30-1/4 inch Bellwether (K-837 left drain, K-838 right drain) drops into the same opening as most standard tubs, weighs 310 lb empty per Kohler’s spec sheet and holds 32.6 gallons. If you want a deeper soak, a 60 x 32 inch version and a 66 x 32 inch version hold more water but weigh more and need a wider or longer alcove. Every figure here comes from Kohler’s current specification sheets, which Kohler notes can change without notice, so confirm the sheet for your exact model number before framing or ordering.

Kohler Bellwether Bathtub Specs at a Glance

Kohler lists separate model numbers for left and right drain. Drain side is decided by where the drain sits when you face the tub, and it must match your existing plumbing or you will need a plumber to move the drain.

Model Size (L x W x H) Apron height Water depth Capacity Empty weight Min. floor load Colors on sheet
K-837 (left) / K-838 (right) 60 x 30-1/4 x 14-1/2 in 14 in 9 in 32.6 gal 310 lb 52 lb/sq ft White, Biscuit, Teal, Aspen Green, Fresh Green
K-876 (right) 60 x 32 x 15-1/2 in 15 in 11-5/16 in 44 gal 327 lb 52 lb/sq ft White, Biscuit
K-847 (left) 66 x 32 x 17 in 16-1/2 in 11-11/16 in 49 gal 380 lb 57 lb/sq ft White, Biscuit
K-848 (right) 66 x 32 x 17 in 16-1/2 in 11-11/16 in 49 gal 400 lb 57 lb/sq ft White, Biscuit
Villager K-715 (left), for comparison 60 x 30-1/4 x 14 in about 14 in 8-5/8 in 33 gal 316 lb 49 lb/sq ft White, Biscuit

A left-drain partner to the 60 x 32 inch K-876 is sold through retailers as the K-875; check its own sheet before relying on the right-drain numbers. All Bellwether sheets list Kohler enameled cast iron, a 1-1/2 inch bath drain, an alcove installation and Kohler’s lifetime limited warranty for enameled cast iron baths and shower bases.

What Sets Bellwether Apart

Kohler’s own feature list for the 60-inch models highlights a 14-inch apron height for easier entry, a standard size that simplifies remodels, an integral flange that helps keep water from seeping behind the wall, the Safeguard slip-resistant bottom, wide ledges for storage, an integral apron and integral lumbar support. Shoppers searching for a Kohler Bellwether tub usually want exactly that mix: a standard alcove footprint with a sturdier, more classic material than acrylic. The longer 66-inch version keeps the wide ledges and slip-resistant surface but raises the apron to 16-1/2 inches.

Enameled cast iron is the reason people seek out this line. The glossy enamel resists scratches and chemicals better than acrylic, holds heat well once warmed, and feels solid underfoot with none of the flex or hollow sound of thinner tubs. The tradeoffs are weight, cost and a slower warm-up: the iron absorbs heat from the first fill of water before it starts to hold it.

Bellwether vs Villager: Which Kohler Cast Iron Tub?

Villager is the other common Kohler 60-inch cast iron alcove tub, and on paper the two look almost identical: both are 60 x 30-1/4 inches, both weigh a little over 300 lb, and both have an integral apron, lumbar support and slip-resistant surface. The differences show up inside the tub and in the styling.

  • Bathing well shape: Bellwether’s bottom basin measures 48-3/4 x 19-5/16 inches per the sheet, a longer, slimmer floor. Villager’s bottom basin is 45 x 22 inches, shorter but wider.
  • Water depth: Bellwether lists 9 inches against Villager’s 8-5/8 inches, while capacity is nearly the same (32.6 vs 33 gallons).
  • Weight and floor load: Bellwether 310 lb and 52 lb/sq ft minimum floor load; Villager 316 lb and 49 lb/sq ft.
  • Colors: the 60-inch Bellwether sheet lists more colors (including Teal, Aspen Green and Fresh Green) than Villager’s White and Biscuit.
  • Style: Bellwether has crisper, more contemporary lines and wide flat ledges; Villager has a softer, more traditional profile.

If you are tall, the longer floor of Bellwether may feel better. If you bathe kids, Villager’s wider floor gives more room to sit. For a genuinely deeper soak, step up to the 60 x 32 or 66 x 32 inch Bellwether.

Planning for the Weight

An empty 60-inch Bellwether at 310 lb plus 32.6 gallons of water (about 270 lb, since water weighs roughly 8.3 lb per gallon) is close to 580 lb before anyone climbs in. The 66-inch K-848 at 400 lb plus 49 gallons (about 410 lb of water) can pass 800 lb with no bather. Kohler’s sheets list minimum floor loads of 52 to 57 lb per square foot for Bellwether models.

That load is the main structural question with any Kohler Bellwether cast iron tub. On a ground floor slab, it is rarely an issue. On a second floor, or over old joists that have been notched for plumbing, have the framing checked. Swapping a steel or acrylic tub for cast iron in the same spot is the classic case where a joist that was fine for years starts to sag.

Looking to buy Kohler Bellwether Bathtub? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Tools and Materials for Installation

  • Kohler installation instructions and the spec sheet for your exact model
  • Bath drain and overflow kit (the sheets recommend cable or toe-tap drains in specific lengths)
  • Level, tape measure and shims rated for wet areas
  • Ledger board or supports per the instructions, plus construction screws
  • Mortar bed or setting compound if the instructions call for one
  • Appliance dolly, furniture straps and at least three or four strong helpers
  • Silicone sealant, cement board, waterproofing membrane for the surround
  • A non-abrasive bathtub cleaner for the finished enamel

Installation Overview: Step by Step

  1. Measure the alcove. Confirm finished-wall length and width. A 60-inch tub needs a true 60-inch opening; the 32-inch-wide models need a deeper alcove than the 30-1/4 inch version.
  2. Confirm drain side and location. Match the left or right drain model to your existing rough-in, or plan the drain move before the tub arrives.
  3. Check the structure. Inspect joists under the tub, and add sistering or blocking where the framing is undersized or damaged.
  4. Shut off water and remove the old tub. Turn off supply lines, drain the lines, and cut or break out the old unit carefully.
  5. Set supports. Install ledgers and any required bed per Kohler’s instructions so the rim and floor are fully supported and level.
  6. Move the tub in safely. Use a dolly and enough people. Protect the enamel and the floors along the route.
  7. Dry fit, level and connect. Install the drain and overflow, set the tub, level it, and test for leaks before closing the walls.
  8. Finish the surround. Run cement board down over the integral flange as the instructions show, waterproof, tile or install panels, and seal with silicone.

Kohler’s sheets also note that your hot water supply should be at least 70 percent of the tub’s capacity, which matters most for the 44 to 49 gallon models. For the 60 x 32 inch version, Kohler recommends a bath spout at least 7 inches long to clear the rim.

Troubleshooting and Care

  • Water drains poorly: the tub may not be level or the drain was set too high. Recheck level and the drain connection.
  • Tub rocks or creaks: the floor is uneven or the support bed is incomplete. Shim or re-bed before the surround goes on.
  • Bath runs cold quickly: the iron absorbs heat at first. Run hot water briefly to warm the tub, and check your water heater size.
  • Dull or stained enamel: stop using abrasive pads and powders. A non-abrasive bathtub cleaner and a soft cloth keep the gloss intact.
  • Chips: small chips can be touched up with porcelain repair kits; larger damage calls for a refinishing pro.

Cost Ranges and When to Call a Licensed Professional

Enameled cast iron alcove tubs generally cost more than acrylic or steel versions of the same size, often in the high hundreds to low thousands of dollars for the tub alone, with the 66-inch and colored versions toward the top. Professional installation for a cast iron tub, including removal, plumbing connections and a new surround, commonly runs from a few thousand dollars upward depending on tile and any framing work.

Hire a licensed plumber for drain, overflow and supply changes; most areas require a permit to move drains or alter supply lines. Bring in a contractor or structural engineer if the tub is going on an upper floor, over damaged or notched joists, or if the floor bounces. Because of the weight, most homeowners are better off paying for an experienced crew to carry and set the tub. If you do DIY, never lift a cast iron tub with fewer than three or four people.

Frequently Asked Questions

How much does a Kohler Bellwether bathtub weigh?

Kohler’s spec sheets list 310 lb for the 60 x 30-1/4 inch models (K-837 and K-838), 327 lb for the 60 x 32 inch K-876, and 380 to 400 lb for the 66 x 32 inch models. Add water and a bather for the full load.

What sizes does Bellwether come in?

Kohler lists 60 x 30-1/4 inches, 60 x 32 inches and 66 x 32 inches, each in left- and right-drain versions. The standard 60 x 30-1/4 inch size fits most existing tub alcoves.

How deep is the Kohler Bellwether tub?

The 60 x 30-1/4 inch model lists a 9-inch water depth. The 60 x 32 inch model lists 11-5/16 inches and the 66 x 32 inch model 11-11/16 inches, so the larger sizes give a noticeably deeper soak.

What colors is the Bellwether cast iron tub available in?

The current 60 x 30-1/4 inch sheets list White, Biscuit, Teal, Aspen Green and Fresh Green. The larger sizes list White and Biscuit. Color availability changes, so check the current Kohler sheet for your model.

Is Bellwether better than Villager?

Neither is better outright. Bellwether has a longer, slimmer bathing floor, slightly more water depth and more modern lines. Villager has a wider, shorter floor and a more traditional look. Both are 60 x 30-1/4 inch enameled cast iron.

Can my floor support a cast iron tub?

Most ground floors can. Upper floors and older or notched joists need checking, since a filled 60-inch Bellwether approaches 580 lb before anyone gets in. Kohler lists minimum floor loads of 52 to 57 lb per square foot.