Home Improvement

Kohler Villager Bathtub: Cast Iron Sizes, Weight and Mendota

Kohler Villager Bathtub: Cast Iron Sizes, Weight and Mendota

A cast iron tub is the kind of purchase that outlives the tile around it, and the kohler villager bathtub is one of the most common ways people get one into a standard 5-foot alcove. Per the maker’s specification sheet, the Villager is an enameled cast iron alcove bath measuring 60 inches long by 30-1/4 inches wide by 14 inches high, weighing 316 pounds, with a water capacity of 33 gallons. It comes with an integral apron, a left-hand drain (K-715) or right-hand drain (K-716) version, and White or Biscuit color options on the current sheet.

If you want more depth and room, the Mendota is the step-up cast iron alcove tub: 60 by 32 by 16-1/4 inches, 351 pounds and 45 gallons. That extra 2 inches of height and 12 gallons of water is the main difference most bathers notice. Both lines are heavy enough that floor framing, delivery and installation planning matter as much as the color choice.

Kohler Villager Bathtub Specs at a Glance

All figures in the table come from the manufacturer’s current spec sheets. The sheets note that dimensions are nominal, so measure the actual tub for rough-in.

Spec Villager (K-715 / K-716) Mendota (K-505) What it means
Overall size 60″ L x 30-1/4″ W x 14″ H 60″ L x 32″ W x 16-1/4″ H Both fit a standard 5 ft alcove; Mendota needs a 32″ wide space
Weight (empty) 316 lbs 351 lbs Plan a three to four person carry or a dolly and ramp
Water capacity 33 gal 45 gal Affects soaking comfort and water heater sizing
Water depth 8-5/8″ 10-7/8″ Depth to the overflow, not the rim
Minimum floor load 49 lbs/sq ft 56 lbs/sq ft Confirm framing can carry tub, water and bather
Basin, top 55″ x 24″ 54″ x 24″ Similar interior length; Mendota gains depth, not length
Basin, bottom 45″ x 22″ 46″ x 20″ Villager has a slightly wider floor to stand on
Drain options Left (715) or right (716) Left (505); check the sheet for the right-drain model Viewed facing the tub’s apron
Colors on spec sheet White (0), Biscuit (96) White (0), Biscuit (96) Other colors may be special order or discontinued

Both tubs use the maker’s enameled cast iron, a slip-resistant bottom surface, integral lumbar support and an integral tiling flange, and both list ADA compliance when installed to the specific requirements. The manufacturer covers its enameled cast iron baths with a lifetime limited warranty; read the current warranty terms for what is and is not covered.

Villager vs Mendota: Which One Fits Your Bathroom?

The Villager is the classic replacement tub. Its 30-1/4 inch width matches most existing 5-foot alcoves built for 30-inch steel or fiberglass tubs, which is why remodelers reach for it when swapping out an old tub without moving walls. The 14-inch height also keeps step-over easier for kids, older adults and anyone with limited mobility.

The Mendota trades that easy fit for comfort. The extra 2 inches of height and roughly 2-1/4 inches of water depth let taller adults get shoulders closer to the water line. But 32 inches of width means you either already have a 32-inch alcove or you are moving a wall or furring out tile backer. A retailer listing showed at least one Mendota variant marked discontinued, so check current availability before you design around it.

Choose the Villager if

  • Your alcove is about 30 inches deep wall to apron
  • You want a lower step-over height
  • Your water heater is a standard 40 or 50 gallon tank
  • Floor framing is older and you want the lighter of the two

Choose the Mendota if

  • You have or can create a 32-inch alcove
  • Soaking depth is the priority
  • Your hot water supply can fill 45 gallons comfortably

Weight, Floor Load and Structural Planning

An empty Villager weighs 316 pounds. Fill it to the overflow with 33 gallons of water (about 275 pounds) and add a bather, and the total load easily passes 700 pounds over a small footprint. The spec sheet lists a minimum floor load of 49 pounds per square foot for the Villager and 56 for the Mendota.

Most modern joist floors built to code handle a cast iron tub fine, but older homes, notched joists, previous plumbing cuts and rot from a leaking tub can all reduce capacity. Before ordering:

  • Inspect joists under the tub from the basement or crawlspace for rot, sag, cuts or notches.
  • Look for previous water damage around the drain and supply area.
  • On a second floor or with any doubt, have a contractor or structural engineer confirm the framing, and add sistered joists or blocking if recommended.
  • Check local permit requirements; tub replacements that alter drain lines or framing often need one.

The manufacturer also notes that the hot water supply should be at least 70 percent of the tub’s capacity. For the Villager that is roughly 23 gallons of hot water; a typical tank heater handles that, but a small tankless unit may fill slowly in winter.

Installation Steps for a Villager Tub

Setting a cast iron tub is not like dropping in an acrylic shell. Its weight helps it sit solidly, but it also makes mistakes hard to correct.

Tools and materials

  • Appliance dolly, furniture straps, plywood runners and at least three helpers
  • Level, tape measure, shims and a pry bar
  • Drain and overflow kit compatible with the tub (the spec sheet lists cable, toe-tap and other options)
  • Plumber’s putty or gasket per the drain maker, and pipe joint compound
  • Mortar or leveling compound if the subfloor is uneven
  • Cement backer board, waterproofing membrane and tile setting materials for the walls

Steps

  1. Shut off water to the bathroom and relieve pressure at a lower faucet.
  2. Remove the old tub and inspect framing, subfloor and drain line.
  3. Confirm the drain side matches your plumbing: K-715 is left drain, K-716 is right drain.
  4. Check the rough-in dimensions from the spec sheet against your actual drain location and measure the tub itself.
  5. Level the subfloor or set the tub in a mortar bed if the floor is uneven, so the tub bottom is supported.
  6. Pre-assemble the drain and overflow on the tub while it is on its side, if your kit allows.
  7. Walk the tub in on runners, tilt it into the alcove and set it level both ways.
  8. Connect the drain to the trap, then fill with water and check for leaks before closing walls.
  9. Install backer board over the integral flange, waterproof and tile, then caulk the tub-to-tile joint with 100 percent silicone.
Looking to buy Kohler Villager Bathtub? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Troubleshooting and Care

  • Tub rocks: The subfloor is not flat. Shim at the feet or reset in a mortar bed; never rely on the tile walls to hold it still.
  • Slow drain: Check that the trap is not undersized and the vent is clear. Hair buildup in the drain shoe is the usual cause.
  • Chipped enamel: Small chips can be touched up with an enamel repair kit. Large damage calls for professional refinishing, which is a separate project from the tub line itself.
  • Dull or stained surface: Use a non-abrasive cleaner made for enameled cast iron. Avoid scouring powders and steel wool, which wear the gloss.
  • Slipping: The built-in slip-resistant surface helps, but a non-slip bath mat adds traction for kids and older bathers.

Cost Ranges

Cast iron alcove tubs sit in the mid-to-upper range for standard 5-foot tubs, generally costing more than steel or acrylic. Installed project costs vary widely:

  • Tub only: commonly several hundred to over a thousand dollars depending on color and drain options
  • Tub swap with existing plumbing and minor wall repair: often $1,500 to $4,000 installed
  • Full alcove remodel with new tile surround: often $5,000 to $12,000 or more

Delivery up stairs, demolition of an old cast iron tub (which often must be broken up with a sledgehammer, with eye and hearing protection) and framing repairs add to the cost.

When to Call a Licensed Professional

Hire a licensed plumber if you are moving the drain, changing the trap, adding a new shower valve or working with old galvanized or cast iron drain lines. A contractor or engineer should check framing when the tub goes on an upper floor or into an older home. Get permits where required. If walls or floors were built before the 1980s, test old joint compound, plaster or flooring adhesive for asbestos before demolition, and test pre-1978 paint for lead.

Frequently Asked Questions

How much does a Kohler Villager tub weigh?

The manufacturer’s spec sheet lists the Villager at 316 pounds empty. Some retailer listings show higher figures that may include packaging, so use the spec sheet number for structural planning.

What size is the Kohler Villager bathtub?

It is 60 inches long, 30-1/4 inches wide and 14 inches high, with a water capacity of 33 gallons and a water depth of 8-5/8 inches to the overflow.

Is the Mendota deeper than the Villager?

Yes. The Mendota is 16-1/4 inches tall with a 10-7/8 inch water depth and 45 gallon capacity, compared with the Villager’s 14 inches, 8-5/8 inches and 33 gallons. It is also 32 inches wide instead of 30-1/4.

How do I know if I need a left or right drain?

Stand facing the tub’s apron and note which end the drain sits at. K-715 is the left-drain Villager and K-716 is the right-drain version. Match it to your existing drain location to avoid moving plumbing.

Can one person install a cast iron tub?

No. At over 300 pounds, a Villager needs at least three or four people, an appliance dolly and a plan for stairs and doorways. Many homeowners pay for delivery and setting even when doing the tile themselves.