The most expensive mistake in a manufactured home kitchen is treating it like a site-built house. A mobile home kitchen remodel works inside lighter floor framing, thinner walls, narrower doors and, in older homes, materials that need testing before anything comes apart. Plan around those limits and you can get a kitchen that looks and works like any modern one.
Part of our Kitchen Remodeling guide — explore the full guide →
Here is the quick version: check the floor and subfloor before you choose heavy stone counters, favor lightweight cabinet boxes, measure every doorway before you buy appliances, keep gas and electrical work in licensed hands, and vent the range to the outside. In homes built before the 1980s, test for asbestos and lead before demolition. Most single and double wide kitchens can be redone for roughly $8,000 to $30,000, depending on how much you move.
- Planning a Mobile Home Kitchen Remodel
- Floor Load and Subfloor Checks
- Cabinets, Counters and Flooring Choices
- Gas vs Electric Range and Venting
- Electrical Work and Aluminum Wiring
- Getting Appliances Through Narrow Doors
- Step-by-Step Remodel Sequence
- Costs and Troubleshooting
- When to Call a Licensed Professional
- Frequently Asked Questions
Planning a Mobile Home Kitchen Remodel
Start by mapping what you can and cannot move. In most single wides, the sink sits on an exterior wall or the marriage line side with plumbing running through the belly of the home. Moving the sink or range means opening the belly wrap, rerouting drains with proper slope, and possibly adding new circuits, which drives cost up fast. Keeping the footprint and upgrading surfaces gives you the most kitchen per dollar, and it is how most budget-minded owners approach a mobile home kitchen remodel.
Single wide trailer kitchen remodel projects usually work with a galley or L layout along one wall, so every inch counts. Double wides have more room and may allow an island, but the island floor needs the same load check as the counters. Measure ceiling height too; many homes have 7 to 7.5 foot ceilings, which limits tall wall cabinets.
Test before demolition in older homes
Homes built before 1978 may have lead in paint, and homes built into the 1980s may have asbestos in vinyl flooring, flooring adhesive, ceiling texture, joint compound or wallboard materials. Do not sand, scrape, cut or tear these out until a sample has been tested by an accredited lab or a licensed inspector. If results are positive, use lead-safe work practices or hire a licensed abatement contractor for asbestos. Keep kids and pets away from the work area either way.
Floor Load and Subfloor Checks
Manufactured home floors are commonly built with 2×6 joists and particleboard or OSB decking, and many older homes have particleboard that swells and crumbles after a leak. A granite or quartz counter with a full-height backsplash can weigh 18 to 25 pounds per square foot of surface, and a loaded base cabinet run adds more. The floor can usually carry it, but only if the decking is sound and the home is level and properly supported on its piers.
- Pull the toe kicks and check the decking at the sink base and dishwasher for soft spots or swelling.
- Replace water-damaged decking with 3/4 inch plywood or OSB rated for floors, glued and screwed to the joists.
- Check that piers under the kitchen area are tight and the home is level; a sagging floor will crack stone counters.
- If you want stone on a long run or an island, ask a contractor or engineer whether added support under the floor is needed.
Lighter options sidestep the question. Laminate counters, solid surface, butcher block and thinner quartz in 2 cm slabs weigh far less than 3 cm granite and still look current.
Cabinets, Counters and Flooring Choices
Original cabinets in many homes are built from thin face frames and wallboard-thin backs. Replacements with plywood boxes are sturdier but heavier, so many owners go with lighter frameless boxes or keep sound boxes and swap doors and hardware. Hang wall cabinets into studs with cabinet screws, not just through the wall panel, since walls in manufactured homes are often thin gypsum or vinyl-covered panels over 2×3 or 2×4 studs.
For flooring, luxury vinyl plank or sheet vinyl suits mobile home kitchen renovation work well: it is light, waterproof and flexes with the home. Install under the cabinets or leave the dishwasher opening clear so you can pull the appliance later. Tile works on a stiff subfloor but adds weight and can crack if the home moves.
Gas vs Electric Range and Venting
Many homes came with a 30-inch electric range, while others have propane or natural gas. Switching fuels is possible but not a DIY job.
- Gas ranges: connecting, moving or converting a gas line must be done by a licensed gas fitter or plumber with a permit and a leak test. Never make gas connections yourself. If you smell gas, leave the home right away and call your gas utility from outside.
- Electric ranges: a full-size range needs a dedicated 240-volt circuit sized for the appliance. Adding or upgrading that circuit is work for a licensed electrician.
- Combustion safety: with any gas appliance, keep carbon monoxide alarms on each level and near sleeping areas.
A range hood that vents outdoors removes grease, moisture and combustion byproducts far better than a recirculating hood. Run rigid metal duct through the wall or roof with a proper exterior cap, never into the ceiling cavity or belly, where moisture will cause rot. In tight kitchens, an apartment-size range at 20 to 24 inches wide frees counter space and still handles everyday cooking.
Electrical Work and Aluminum Wiring
Kitchens need several dedicated circuits, and countertop outlets near the sink must be GFCI protected. Before you touch any switch, outlet or fixture, turn off the breaker and confirm power is off with a non-contact voltage tester. Swapping a fixture on an existing circuit is a reasonable DIY task; adding outlets, new circuits or a bigger range circuit belongs with a licensed electrician.
Some homes from the late 1960s and 1970s were wired with aluminum branch circuits. Aluminum wiring connected to devices not rated for it can overheat at the terminals. If you see dull silver conductors or “AL” markings on the cable jacket, stop and have a licensed electrician evaluate and repair connections with approved methods. Plug the refrigerator, microwave and other large appliances directly into wall outlets rather than extension cords or power strips.
Getting Appliances Through Narrow Doors
Exterior doors on manufactured homes are often 32 to 34 inches wide, with interior openings narrower still. A standard 36-inch-deep refrigerator can be a tight fit. Measure the door, the hallway turns and the kitchen opening, then compare against the appliance depth with doors removed. Counter-depth refrigerators, 24-inch dishwashers and apartment-size ranges all slip through more easily. Many delivery crews will pull the door slab or remove handles if you ask in advance.
Step-by-Step Remodel Sequence
- Measure and design. Draw the room to scale, mark plumbing, gas and electrical locations, and note door widths.
- Test hazardous materials in older homes and arrange abatement if needed.
- Shut off utilities. Turn off water at the fixture or main and relieve pressure; have the gas fitter cap any gas line; turn off breakers and verify with a non-contact tester.
- Demolish carefully. Remove counters, then wall and base cabinets. Protect the floor if you are keeping it.
- Repair the subfloor and confirm the home is level and supported.
- Rough-in changes with licensed trades for plumbing, gas and electrical, with permits where required.
- Install flooring, cabinets and counters, then backsplash.
- Set appliances, with the gas fitter making any gas connection and leak test.
Costs and Troubleshooting
Budget ranges for a typical project: a cosmetic refresh with paint, hardware, laminate counters and new vinyl flooring often lands between $3,000 and $8,000. A mid-range job with new cabinets, solid surface or quartz and new appliances runs about $10,000 to $25,000. Moving plumbing or adding gas or circuits pushes higher. Abatement, subfloor repairs and permits are separate line items worth budgeting up front.
- Counters not level: usually a floor or pier problem; fix support before shimming cabinets.
- Cabinet pulling off the wall: screws missed the studs; locate framing and refasten.
- Breaker trips with new appliances: circuit overloaded; have an electrician assess capacity.
- Grease and moisture on ceiling: range hood recirculating or ducted into the cavity; vent outdoors.
When to Call a Licensed Professional
Bring in licensed trades for any gas line, new circuit, panel work, aluminum wiring repair, plumbing relocation or structural change. Many areas require permits for these, and a manufactured home may have extra rules from the state agency that oversees them. A general contractor experienced with manufactured housing can coordinate trades and check floor support before heavy counters go in.
Frequently Asked Questions
Can a mobile home floor hold granite countertops?
Often yes, if the subfloor is solid, the joists are undamaged and the home is properly supported. Check for soft decking and ask a contractor about added support for long runs or islands.
Can I switch from electric to a gas range?
It is possible where gas is available, but a licensed gas fitter must run and test the line under a permit. If you ever smell gas, leave and call the utility.
What size range fits a small mobile home kitchen?
Standard ranges are 30 inches wide, but 20 to 24 inch apartment-size models fit tight galley kitchens and narrow doors.
Do older mobile homes have asbestos?
Some do, especially in flooring, adhesives and ceiling textures from before the 1980s. Test before disturbing these materials.
How much does a single wide kitchen remodel cost?
A cosmetic refresh may be $3,000 to $8,000, while a full remodel with new cabinets and appliances commonly runs $10,000 to $25,000.