Home Improvement

Standard Interior Door Size Chart for Every Room

Standard Interior Door Size Chart for Every Room

Ordering a replacement door and guessing the size is how homeowners end up with a slab that swallows the hallway or a bathroom door too narrow for code. This standard interior door size chart lays out the widths, heights, and rough openings you actually need, room by room, so you measure once and buy right. Interior doors in the U.S. follow predictable dimensions, and knowing them saves you a return trip and a lot of shimming.

The Quick-Reference Size Chart

Most residential interior doors come in a handful of standard widths, all sharing the same common height. Here is the core standard interior door size chart builders rely on:

  • 1 ft 6 in (18 in) wide: Small closets, pantries, and tight utility spaces.
  • 2 ft 0 in (24 in) wide: Closets, half-baths in older homes, and secondary spaces.
  • 2 ft 4 in (28 in) wide: Bathrooms and smaller bedrooms.
  • 2 ft 6 in (30 in) wide: The most common bedroom and bathroom door.
  • 2 ft 8 in (32 in) wide: Bedrooms and the minimum for wheelchair accessibility.
  • 3 ft 0 in (36 in) wide: Main bedrooms, ADA-compliant passages, and where a wider swing is wanted.

The standard height for nearly all of these is 6 ft 8 in (80 in). Standard interior door thickness is 1 3/8 in for most hollow-core and many solid-core slabs, while exterior and some heavy solid doors run 1 3/4 in.

Standard Interior Door Sizes in Centimeters

For metric plans or imported doors, the standard U.S. interior door sizes convert to the following, rounded to the nearest tenth of a centimeter. The standard 80-inch height equals 203.2 cm, and an 82.5-inch rough opening height equals about 209.6 cm.

Door width (inches) Door width (cm) Rough opening width (cm)
18 in (1/6) 45.7 cm 50.8 cm
24 in (2/0) 61.0 cm 66.0 cm
28 in (2/4) 71.1 cm 76.2 cm
30 in (2/6) 76.2 cm 81.3 cm
32 in (2/8) 81.3 cm 86.4 cm
36 in (3/0) 91.4 cm 96.5 cm

Understanding Nominal vs. Actual Sizes

Door widths are often written in a shorthand that trips people up. A door labeled 2/6 means 2 feet 6 inches, or 30 inches, and 2/8 means 32 inches. The number stamped on the door refers to the slab’s actual dimension, not the opening. So a 30-inch door measures 30 inches across the slab itself. The confusion usually starts when you factor in the frame and the rough opening, which are larger to accommodate the jamb and shimming space. Always confirm whether a listing quotes the slab size or the pre-hung unit size, because a pre-hung 30-inch door needs a wider hole in the wall than the slab alone.

Rough Opening Dimensions You Need to Frame

If you are building or moving a wall, the rough opening is what matters. The rule of thumb is to add 2 inches to the door width and 2.5 inches to the door height for a pre-hung interior door. That extra space leaves room for the 3/4-inch jamb on each side plus shim clearance to plumb and level the frame. For example:

  • A 30-inch (2/6) door needs a rough opening of about 32 inches wide by 82.5 inches tall.
  • A 32-inch (2/8) door needs roughly 34 inches wide by 82.5 inches tall.
  • A 36-inch (3/0) door needs about 38 inches wide by 82.5 inches tall.

Frame the header height at 82.5 inches from the subfloor so the finished 80-inch door clears carpet, tile, or a threshold with a comfortable gap underneath. If you are installing over thick flooring, add a bit more.

Door Sizes by Room

Different rooms lean toward different widths for practical reasons. Bedrooms typically use a 30- or 32-inch door, wide enough to move furniture through without feeling cavernous. Bathrooms most often get a 28- or 30-inch door, though building codes in many areas require a minimum 32-inch clear width for accessibility in new construction, which pushes bathroom doors wider than they used to be. Closets vary the most: a reach-in closet might use a single 24- or 30-inch door, a small linen closet a 24-inch, and a walk-in a full 30- or 32-inch passage door. Double doors, bifolds, and bypass sliders cover wider closet openings from 4 to 8 feet.

Non-Standard and Custom Sizes

Older homes and custom builds break the rules constantly. Houses built before the 1960s frequently have doors under 80 inches tall or oddball widths that no big-box store stocks. Modern high-end construction often specs 8-foot (96-inch) tall doors for a dramatic, contemporary look, and these command a premium. When you hit a non-standard opening, you have three options: order a custom slab from a millwork shop, trim a taller stock door down to fit, or reframe the opening to accept a standard size. Trimming is only safe within limits; you can usually shave up to 3/4 inch off a hollow-core door before you cut into the hollow center, and solid-core doors allow more.

Looking to buy Standard Interior Door Size Chart for Every Room? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Measuring an Existing Door Correctly

To replace a slab and reuse the frame, measure the old door itself, not the opening. Take the width across the widest point, the height from top to bottom, and the thickness of the edge. Note the hinge locations and the height of the doorknob bore, standard at 36 inches to center, so your new slab matches. Count the hinges too, since heavier solid-core doors often use three while lightweight hollow-core doors may use two. If you are replacing a full pre-hung unit, measure the rough opening in the wall by pulling back the trim, and check that the floor is level, because an out-of-plumb opening is the number-one reason a new door binds or swings on its own.

Buying the Right Door the First Time

Before you head to the store, write down the slab width, the height, the thickness, the swing direction, and whether you need a slab only or a pre-hung unit. Determine the handing by standing in the opening facing the way the door swings away from you; if the hinges are on your left it is a left-hand door. Match the jamb width to your wall thickness, commonly 4 9/16 inches for a 2×4 wall with 1/2-inch drywall on each side. Nail those details down and this standard interior door size chart turns a potentially frustrating project into a straightforward afternoon swap.

Slab Thickness and Jamb Width

Width and height get the attention, but two other dimensions decide whether a door fits and functions. Slab thickness matters because most interior hollow-core and many solid-core doors are 1 3/8 inches thick, while heavier solid-core and solid-wood doors, along with all exterior doors, run 1 3/4 inches. Ordering a 1 3/4-inch slab to fit a jamb bored for 1 3/8 inches means the latch and strike will not align, so match the thickness to your existing setup. Jamb width is equally important on a prehung unit and must equal the total wall thickness, framing plus drywall on both sides. A standard 2×4 wall finished with 1/2-inch drywall each side measures 4 9/16 inches, the most common jamb width, while a 2×6 plumbing wall or a wall with thicker finishes needs a wider jamb. Measure your wall thickness before ordering a prehung door, because a jamb that is too narrow or too wide leaves the casing sitting proud of or recessed behind the wall.

Bore Location and Hardware Prep

When you buy a slab, the hardware prep must match your hardware or you will be drilling. The standard doorknob bore sits 36 inches from the floor to its center, with a 2 1/8-inch face bore for the knob and a 1-inch edge bore for the latch. Backset, the distance from the door edge to the center of the knob bore, is standard at 2 3/8 inches for interior doors, though 2 3/4 inches is also common. Hinge locations are standardized too, typically with the top hinge 7 inches from the top of the door, the bottom hinge 11 inches from the bottom, and a third hinge centered between them on heavier doors. If you are reusing an existing frame, order a slab pre-bored to match, or buy a blank slab and drill it yourself with a knob installation kit. Matching these details saves a frustrating afternoon of trying to make mismatched parts line up.

Buying With Confidence

With the full chart and these extra dimensions in hand, ordering a door becomes straightforward. Write down the slab width, height, thickness, swing direction and handing, the bore and backset, the hinge count and locations, and, for a prehung, the rough opening and jamb width. Take those numbers to the store or the online listing and confirm each one against the product specs before you buy. If your opening is non-standard, decide early whether to order custom, trim a stock door within the safe limit of about 3/4 inch on a hollow-core, or reframe to a standard size. Nailing down every dimension in advance turns door replacement from a guessing game into a confident purchase, and this standard interior door size chart gives you the reference to get it right the first time.

Frequently Asked Questions

What are standard interior double door sizes?

Interior double doors are usually a pair of matching slabs, so common total widths are 48 inches (two 24-inch doors), 60 inches (two 30-inch doors), and 72 inches (two 36-inch doors), all at the standard 80-inch height. The rough opening for a prehung pair is typically about 2 inches wider and 2.5 inches taller than the combined door size, just like a single door.

How wide is a bedroom door with the frame and trim?

Add roughly 6 to 8 inches to the slab width for the full width with frame and trim. The jamb adds about 3/4 inch on each side, and standard casing trim adds another 2 1/4 to 3 1/2 inches per side. A 30-inch bedroom door therefore usually takes up about 36 to 38 inches of wall once trimmed out.

Will a mattress fit through a standard interior door?

Yes, in most cases. Turned on its side, a queen or king mattress is only about 10 to 14 inches thick, so it passes easily through a 30- or 32-inch door, and the 80-inch door height clears a mattress length standing upright. Trouble usually comes from tight hallway turns, not the door itself; removing the door from its hinges adds about 1 3/8 inches of clearance.

How much gap should be under and around an interior door?

Aim for about 1/8 inch along the top and both sides and roughly 3/8 to 1/2 inch between the bottom of the door and the finished floor. The bottom gap clears rugs and carpet and lets air move between rooms for heating and cooling. Over thick carpet, a slightly larger gap may be needed so the door does not drag.