Home Improvement

Sub-Zero 48 Inch Refrigerator and Full Sub-Zero Size Chart

Sub-Zero 48 Inch Refrigerator and Full Sub-Zero Size Chart

Built-in refrigerators are sized to the cabinet opening, not the other way around, and a quarter inch can decide whether a delivery crew installs your unit or loads it back on the truck. Sub-Zero full-size built-ins share a common height of about 84 inches and a depth of about 24 inches, so the number that changes is width: 18, 24, 30 and 36 inches for columns, and 30, 36, 42 and 48 inches for combination units. The Sub-Zero 48 inch refrigerator is the largest single unit in the lineup, offered as a side-by-side, a French door and a PRO model.

Sub-Zero currently groups its full-size refrigeration into three series: Classic, Designer and PRO. Classic models are the familiar stainless or panel-ready built-ins with a visible grille. Designer models are fully integrated, meant to disappear behind cabinet panels, and include the column units. PRO models carry the heavier stainless look and, in the 48-inch size, a glass-door option. Underneath the styling, all of them follow the same 84 by 24 inch envelope, which makes planning simpler than with freestanding fridges.

Sub Zero 48 Inch Refrigerator and Full Size Chart

These figures come from Sub-Zero product and specification pages and from manufacturer spec sheets published by authorized dealers. Cutout dimensions vary slightly between overlay and flush-inset installs, and between models, so always confirm with the current installation guide for your exact model number before cabinets are built. Sub-Zero fridge dimensions are nominal, so the opening is usually a fraction of an inch smaller than the unit’s listed width and height.

Width and type Example model Overall size (W x H x D) Typical opening or cutout Capacity
18″ Designer column (freezer) DEC1850FI 18 x 84 x 24 in About 84 in high opening, 24 in deep Check spec sheet
24″ Designer column refrigerator DEC2450R 24 x 84 x 24 in About 84 in high opening, 24 in deep 13.3 cu ft
36″ Designer column refrigerator DEC3650R 36 x 84 x 24 in About 84 in high opening, 24 in deep 21.7 cu ft
36″ Classic French door CL3650UFD 36 x 84 x 24 in Per installation guide About 20.5 cu ft (dispenser version)
42″ Classic side-by-side CL4250S 42 x 84 x 24 in 41 1/2 W x 83 3/4 H x 24 D in About 24.8 cu ft
48″ Classic side-by-side CL4850S 48 x 84 x 24 in Per installation guide About 29.1 cu ft
48″ Classic French door CL4850UFD 48 x 84 x 24 in 47 1/2 W x 83 3/4 H x 24 D in About 28.9 cu ft
48″ PRO side-by-side PRO4850 48 x 84 x 24 in 47 1/2 W x 83 3/4 H x 24 D in About 30.4 cu ft

Capacity figures shift a little between finish and dispenser variants of the same width, so the numbers in the table are approximate. Column units can also be paired side by side, for example a 30-inch refrigerator column next to an 18-inch freezer column, to create a custom wall of refrigeration wider than 48 inches.

48-Inch Layout Options Compared

If you are searching for a sub zero 48 inch refrigerator, you are choosing between three layouts that all fit the same roughly 48 by 84 by 24 inch opening. The decision comes down to how you use the space.

48-inch side-by-side

The Classic side-by-side splits the width vertically, with the refrigerator on one side and the freezer on the other. It offers the most freezer capacity at eye level and narrow door swings, which helps in galley kitchens or where an island sits close to the fridge wall. Classic side-by-side models come with or without an internal ice and water dispenser, and in stainless or panel-ready versions. The PRO 48 is a side-by-side as well, with the heavier stainless frame and an optional glass refrigerator door.

48-inch French door

The Classic French door model puts a wide refrigerator compartment on top with two doors and freezer drawers below. It suits people who use fresh food more than frozen, and it gives the widest open shelf for sheet trays and party platters. The two half-width doors still swing less than a single 48-inch door would. Manufacturer spec sheets list the stainless 48-inch French door at about 702 pounds, so plan the delivery path and floor accordingly.

Which 48-inch layout fits your kitchen

  • Tight aisle (under about 42 inches): side-by-side, for the narrower door swings.
  • Big fresh-food user: French door, for the wide upper compartment.
  • Large frozen-food storage at eye level: side-by-side.
  • Professional-style range nearby: PRO 48, to match the look.
  • Fully hidden look: consider a pair of Designer columns instead of one 48-inch unit.

Sub-Zero Fridge Sizes by Width

18 and 24 inches. These are Designer column widths, usually used as a freezer column, wine column or a supplemental refrigerator. An 18-inch freezer column paired with a 30-inch refrigerator column is a common combination.

30 inches. Available as a Designer column and as over-and-under units, where the refrigerator sits on top and a freezer drawer below. A 30-inch is the usual choice for smaller kitchens or a secondary fridge in a butler’s pantry.

36 inches. A popular Sub-Zero width. You can choose a Classic French door, a Classic over-and-under, or a 36-inch Designer refrigerator column. A 36-inch opening also matches many standard cabinet plans, which makes it the easiest replacement.

42 inches. Available as a side-by-side and as a French door. It adds meaningful capacity over 36 inches without requiring a 48-inch opening.

48 inches. The largest single unit, in Classic side-by-side, Classic French door and PRO side-by-side form.

How to Measure for a Sub-Zero Built-In

Built-in refrigerators are installed into a finished opening, so measurements matter more than with freestanding units. A laser distance measure makes the job faster and more accurate than a tape in a deep recess.

  1. Measure the width at the top, middle and bottom of the opening. Use the smallest number.
  2. Measure the height from the finished floor to the underside of the soffit or cabinet above, at the front and back and on both sides. Use the smallest number. If new flooring is going in, measure from the new floor height.
  3. Measure the depth from the back wall to the front face of the adjacent cabinet boxes.
  4. Check square and level. An out-of-level floor can reduce usable height.
  5. Locate utilities. Confirm where the electrical outlet and water line sit relative to the installation guide’s recommended zones, so they do not interfere with the unit sliding back.
  6. Plan door clearance. Check that the door can open fully past adjacent walls, islands and countertops, and that drawers can be removed. Flush-inset installs need extra clearance per the design guide.
  7. Measure the delivery path. Doors, hallways and stair turns must clear the unit’s depth and weight.
Looking to buy Sub-Zero 48 Inch Refrigerator and Full Sub-Zero Size Chart? Compare top-rated options.
Shop on Amazon →Browse Our Shop
As an Amazon Associate we earn from qualifying purchases.

Overlay vs Flush Inset Installation

In a standard overlay install, the refrigerator face sits slightly proud of the cabinets, and panels or stainless doors overlap the frame. Flush inset puts the door face in line with the cabinet faces for a cleaner, furniture-like look. Flush inset requires a deeper and more precise opening and adds door clearance, and Sub-Zero publishes separate dimensions for it. If you want flush inset, decide before the cabinetmaker builds the box; retrofitting an opening for flush inset is costly.

Troubleshooting Fit Problems

The unit is slightly too tall. Height leveling legs usually allow a small range of adjustment. Beyond that, a soffit or cabinet above may need to be trimmed. New flooring is the most common cause of a “shrinking” opening.

The doors hit the adjacent wall. Built-ins with a wall right next to the hinge side may not open fully. The design guide lists minimum side clearances; a filler strip between wall and unit is the usual fix.

The old opening is from a legacy model. Older Sub-Zero units, such as the earlier BI-48S side-by-side at 48 by 84 by 24 inches, often fit current openings, but grille height, depth and utility locations can differ. Check the old model number against the new installation guide before ordering.

Panels do not line up. Panel-ready models require custom panels cut to Sub-Zero’s specs. Give your cabinetmaker the design guide, not just overall dimensions.

Cost Range and Installation Notes

Sub-Zero 48-inch models are a premium purchase, typically priced well into five figures, with PRO and dispenser models at the top of the range. Professional installation, custom panels for panel-ready units and any cabinet modifications add to the total, often by several thousand dollars. Prices change frequently, so get a current quote from an authorized dealer.

Most built-ins need a dedicated, properly grounded electrical outlet and a water supply line for the ice maker. Turn off the breaker and confirm power is off with a non-contact voltage tester before working near the outlet, and have a licensed electrician add a new circuit or relocate the outlet. A plumber should run or reroute the water line. Because these units are very heavy and tall, use an anti-tip strap or bracket as specified by the maker and let the installation crew move and level the unit.

Frequently Asked Questions

What are the dimensions of a Sub-Zero 48 inch refrigerator?

Current 48-inch Classic and PRO models measure about 48 inches wide, 84 inches tall and 24 inches deep. Cutouts for the French door and PRO models are listed at about 47 1/2 by 83 3/4 by 24 inches; confirm with your model’s guide.

What widths do Sub-Zero built-in refrigerators come in?

Designer columns come in 18, 24, 30 and 36 inches. Combination refrigerators come in 30, 36, 42 and 48 inches.

How deep is a Sub-Zero built-in refrigerator?

Most full-size built-in models are about 24 inches deep, so they sit nearly flush with standard base cabinets.

Is a 48-inch Sub-Zero available as a French door?

Yes. The Classic series includes a 48-inch French door model alongside the 48-inch side-by-side and the PRO 48.

Can I replace an old Sub-Zero with a new one in the same opening?

Often, but not always. Grille height, depth and utility placement have changed over the years, so compare the old model number to the current installation guide.

Do Sub-Zero columns fit together?

Yes. Designer columns are made to be paired, such as a refrigerator column next to a freezer column, to create a wider custom layout.