Ordering a replacement basement window by eyeballing the old one is the fastest way to end up with a unit that will not fit the opening. Basement window sizes follow a handful of common standards, but the number on the label rarely matches what you see from inside, because frames, bucks and old steel casings hide part of the opening. Measure the rough opening, identify a poured, block or framed wall, and decide early whether the room needs an egress window. Those three facts determine almost every choice that follows.
Part of our Windows & Doors guide — explore the full guide →
The quick answer: the most common standard basement window size is 32 inches wide by 14 inches tall, followed closely by 32 by 16, 32 by 18, 32 by 20, 32 by 22 and 32 by 24. Most are hopper windows that tilt inward from the top, or two-panel sliders. Those small units bring in light and air, but none of them is large enough to serve as an emergency exit. A basement bedroom generally needs a much larger egress opening with a window well outside.
- Standard Basement Window Sizes Chart
- How Foundation Type Affects Basement Window Dimensions
- How to Measure a Basement Window Opening
- Hopper, Slider or Awning: Picking a Style
- When You Need a Larger Egress Window
- Safety and Structural Considerations
- Troubleshooting Fit Problems
- Cost Ranges and When to Call a Pro
- Frequently Asked Questions
Standard Basement Window Sizes Chart
Manufacturers list basement windows by nominal size, width first and height second. Actual unit dimensions usually run about 1/2 inch smaller in each direction so the window can be shimmed into the opening. Here are the sizes you will see most often in stores and on quotes:
| Nominal size (W x H) | Typical style | Common use |
|---|---|---|
| 32 x 14 in | Hopper or slider | Older poured foundations, utility rooms |
| 32 x 16 in | Hopper or slider | Block foundations (two block courses) |
| 32 x 18 in | Hopper | Mid-height openings |
| 32 x 20 in | Hopper or slider | Finished basements wanting more light |
| 32 x 22 in | Hopper or slider | Taller openings, rec rooms |
| 32 x 24 in | Slider | Above-grade or walkout basements |
| 24 x 14 to 24 x 24 in | Hopper | Narrow openings between joists |
Widths of 32 inches dominate because older homes were built with steel basement window frames in that width, sized to fit neatly in foundation forms and block courses. Narrower 24-inch and wider 36-inch units also exist, and many vinyl manufacturers build custom sizes in 1/8 inch increments at a modest upcharge.
How Foundation Type Affects Basement Window Dimensions
The wall you are cutting into, or the wall that already holds the window, shapes the size and the installation method.
Poured concrete walls
Poured foundations typically run 8 to 10 inches thick. Original windows were often set in a steel buck cast right into the concrete. When you replace them, you can either fit a vinyl insert inside the existing steel frame, which shrinks the glass slightly, or remove the steel frame to gain an inch or more of height. Removing cast-in steel takes grinding and patience, and you must not crack the surrounding concrete.
Concrete block walls
Block walls are built in 8-inch courses, so window heights tend to land on multiples of block: two courses equals roughly 16 inches, three courses roughly 24 inches. A 32 by 16 opening is very common in block basements. Block walls are often 8, 10 or 12 inches thick, and the hollow cores must be filled or capped around the opening.
Framed walls and rim joist openings
In some homes, basement windows sit above the foundation in the framed wall or rim joist area. These openings use standard framing practices and may accept regular sliders or awnings. Any cut that removes framing in a bearing wall needs a header.
Wall depth matters for the frame
Measure the thickness of the wall at the opening. Most vinyl basement windows have a 3 to 4 inch frame depth, so a thick foundation leaves a deep return on the inside. Installers usually fill that space with a pressure-treated wood buck or wrap it with vinyl or aluminum trim. Wall depth also affects how far the window sits from the exterior face, which matters for drainage and window well fit.
How to Measure a Basement Window Opening
You only need a tape measure, a flashlight, a level and a notepad. Measure in three places for each direction and use the smallest number.
- Remove any interior trim so you can see the true opening edges.
- Measure the width at the top, middle and bottom of the opening, from masonry to masonry or buck to buck.
- Measure the height at the left, center and right.
- Measure both diagonals. If they differ by more than about 1/4 inch, the opening is out of square and you will need more shimming room.
- Measure wall depth from the inside face to the outside face.
- Subtract about 1/2 inch from the smallest width and height to get the ordering size for a replacement unit.
- Note whether you are keeping or removing the old steel frame, since that changes the opening.
Basement window sizes on a quote should match these notes exactly. Write down the window style you want, the location of any exterior obstacles such as a deck or downspout, and whether a window well already exists. That information keeps the quote accurate.
Hopper, Slider or Awning: Picking a Style
The style changes how much air the window moves and how easy it is to clean.
- Hopper windows hinge at the bottom and tilt in from the top. They seal tightly, shed rain away from the sash, and fit short openings well. This is the classic basement hopper window and the default choice for most foundations.
- Sliders have one fixed and one sliding sash. They open to about half the width and work well where a tilting sash would hit a ceiling or ductwork.
- Awning windows hinge at the top and swing out. They need clear space outside, so they suit above-grade walls more than window wells.
- Fixed glass block or fixed vinyl units give light and security without ventilation.
Low-E, insulated glass helps reduce condensation and heat loss. Basements are humid, so look for a frame with good drainage and consider tempered glass for any window near a stair or within a wet area.
When You Need a Larger Egress Window
Standard cellar windows sizes like 32 by 14 are for light and ventilation only. If the basement contains a sleeping room, most residential codes require at least one emergency escape and rescue opening, commonly called an egress window. Local codes vary, so confirm with your building department, but the general requirements look like this:
- A minimum net clear opening area of around 5 to 5.7 square feet, depending on the floor level and local adoption.
- A minimum clear opening height of about 24 inches and width of about 20 inches.
- A sill no more than about 44 inches above the finished floor.
- A window well large enough to let a person climb out, with a ladder or steps if the well is deep.
A 32 by 22 hopper cannot meet those numbers no matter how it opens. Egress windows are usually casements or large sliders around 36 to 48 inches wide and 36 to 48 inches tall, and installing one typically means cutting a much larger hole in the foundation, excavating outside and setting a new well. That is a permitted structural project.
Safety and Structural Considerations
Enlarging any foundation opening changes how the wall carries soil and house loads. A wider cut in a poured wall may require a steel or concrete lintel. In block, the courses above need support, and cores must be filled. Call 811 before digging outside to locate buried gas, electric and communication lines. Check with your HOA if exterior changes need approval, and pull a permit for any new or enlarged opening.
Wear eye protection, gloves and a respirator when grinding or cutting concrete. Concrete dust contains crystalline silica, so cut wet when possible and clean up with a HEPA vacuum. Keep children and pets away from open window wells during the project.
Troubleshooting Fit Problems
- New window too tall: the old steel frame was left in place. Either order a smaller insert or remove the steel.
- Large gaps around the unit: fill with backer rod and sealant outside and low-expansion foam inside. Do not over-foam, since it can bow the frame.
- Sash will not open fully: check for overhead ductwork or a ceiling soffit. A slider may work better than a hopper.
- Condensation on new glass: basement humidity is high. Run a dehumidifier and keep interior trim gaps sealed.
- Water at the sill: the well drain may be clogged, or the exterior grade slopes toward the house.
Cost Ranges and When to Call a Pro
A standard vinyl hopper or slider in a common size usually costs between roughly one hundred and a few hundred dollars for the unit. Professional replacement in an existing opening often lands in the few hundred dollar range per window, more if old steel frames must be removed. A full egress window installation with excavation, cutting, a well and finishing typically runs into the low to mid thousands.
Replacing a basement window in an existing opening is a manageable DIY project. Call a contractor when you need to enlarge or create an opening, when the wall shows cracks or bowing, when water problems keep returning, or when the room will be used for sleeping.
Frequently Asked Questions
What is the most common basement window size?
The most common standard basement window size is 32 inches wide by 14 inches tall, with 32 by 16, 32 by 20 and 32 by 22 close behind.
Are basement window dimensions measured width first?
Yes. Sizes are listed width by height, so a 32 by 22 window is 32 inches wide and 22 inches tall.
Can a standard hopper window serve as an egress window?
No. Typical hopper sizes are too small to meet the minimum clear opening area and dimensions that codes require for emergency escape.
Should I remove the old steel frame when replacing a basement window?
Removing it gains glass area and gives a cleaner fit, but it takes more work. Leaving it in place and installing an insert is faster.
Do I need a permit to replace a basement window?
Same-size replacements often do not, but enlarging an opening or adding an egress window usually requires a permit. Check with your local building department.