Laminate flooring is one of the most DIY-friendly floor types on the market. Click-lock profiles, no glue, and straightforward instructions make it appealing for first-time installers. But “easy to install” does not mean “impossible to mess up.” Even small oversights during preparation or laying can lead to buckling, gaps, squeaks, and premature wear.
This guide walks through the most common mistakes people make when laying laminate flooring — and exactly how to avoid each one.
- Mistake 1: Skipping Subfloor Preparation
- Mistake 2: Not Acclimatising the Laminate
- Mistake 3: Forgetting the Expansion Gap
- Mistake 4: Installing Without a Vapour Barrier
- Mistake 5: Choosing the Wrong Underlayment
- Mistake 6: Not Staggering the Joints
- Mistake 7: Forcing Planks Together
- Mistake 8: Installing Around Door Frames Incorrectly
- Mistake 9: Starting Along an Out-of-Square Wall
- Mistake 10: Ignoring the Direction of Light
- Mistake 11: Installing Laminate in Wet Areas Without Protection
- Mistake 12: Not Leaving Transition Strips
- Mistake 13: Using the Wrong Cleaning Products
- Mistake 14: Not Checking Planks for Defects
- Mistake 15: Pinning the Floor Down
- Frequently Asked Questions
- Final Thoughts
Mistake 1: Skipping Subfloor Preparation
The Problem
Laminate is a floating floor, which means it sits on top of the subfloor rather than being fastened to it. Every bump, dip, and ridge in the subfloor transfers directly into the laminate surface. Uneven subfloors cause hollow spots, clicking sounds, and can even crack the locking mechanisms over time.
The Fix
Check the subfloor with a long straightedge or level. Industry standards allow no more than 3/16 inch of variation over a 10-foot span. Sand down high spots and fill low spots with self-levelling compound. Remove any old adhesive residue, protruding nails, or debris. A flat, clean subfloor is the foundation of a successful laminate installation.
Mistake 2: Not Acclimatising the Laminate
The Problem
Laminate planks expand and contract with changes in temperature and humidity. If you install them straight from a cold warehouse or delivery truck, the planks will adjust to your home’s climate after installation — potentially expanding and buckling or contracting and gapping.
The Fix
Unbox the laminate and lay the planks flat in the room where they will be installed. Let them acclimatise for at least 48 hours. Keep the room at normal living temperature (between 65 and 85 degrees Fahrenheit) and humidity (35 to 65 percent).
Mistake 3: Forgetting the Expansion Gap
The Problem
This is the single most common laminate flooring mistake. Laminate needs room to expand. If planks are pushed tight against walls, door frames, cabinets, or pipes, the floor has nowhere to go when it swells — resulting in buckling, peak joints, and lifted edges.
The Fix
Leave a gap of at least 1/4 inch (6 mm) around the entire perimeter of the room and around all fixed objects. Use spacers during installation to maintain consistent spacing. The gap will be hidden by baseboards or quarter-round moulding once the floor is complete.
Mistake 4: Installing Without a Vapour Barrier
The Problem
Moisture migrating from concrete subfloors or crawl spaces can warp the HDF core of laminate planks. Without a vapour barrier, you are gambling on the moisture levels remaining low — a bet that rarely pays off.
The Fix
Over concrete subfloors, always install a 6-mil polyethylene vapour barrier or use an underlayment with an integrated moisture barrier. Overlap seams by at least 8 inches and tape them with moisture-barrier tape. Over plywood subfloors above a well-ventilated crawl space, a vapour barrier is still recommended as a precaution.
Mistake 5: Choosing the Wrong Underlayment
The Problem
Underlayment provides cushioning, sound absorption, and minor levelling. Using the wrong type — or skipping it entirely — leads to a noisy, uncomfortable floor. Some laminate comes with pre-attached underlayment; adding a second layer on top doubles the cushion and causes the floor to feel spongy and unstable.
The Fix
If your laminate has pre-attached underlayment, do not add another layer (except a standalone vapour barrier if needed over concrete). If the laminate does not have attached underlayment, use a quality foam or cork product rated for laminate flooring. A 2 mm to 3 mm thickness is standard.
Mistake 6: Not Staggering the Joints
The Problem
End joints that line up across adjacent rows create a visible seam line — an obvious “grid” pattern that looks unnatural and weakens the floor structure. This is known as an H-joint or stairstepping and is one of the most noticeable aesthetic errors.
The Fix
Stagger end joints by at least 12 inches (some manufacturers require 16 or even 24 inches). Use the offcut from the end of one row to start the next row, provided it is long enough. Random staggering looks the most natural.
Mistake 7: Forcing Planks Together
The Problem
When a plank does not click in easily, the temptation is to hammer it harder. Excessive force damages the locking tongue and groove, resulting in joints that will not stay together, gaps, or cracked edges.
The Fix
Always use a tapping block and a rubber mallet — never strike the plank directly. If a plank resists, check for debris in the locking channel, a slight misalignment, or a damaged edge. A gentle approach preserves the locking integrity.
Mistake 8: Installing Around Door Frames Incorrectly
The Problem
Trying to cut laminate to fit around a door frame or casing results in ugly, visible gaps. The laminate also loses its expansion gap coverage in these areas, leading to exposed edges that collect dirt.
The Fix
Undercut the door frames and casings with a flush-cut saw or a multi-tool so the laminate slides underneath. This creates a clean, professional look and maintains the expansion gap behind the casing where it is hidden.
Mistake 9: Starting Along an Out-of-Square Wall
The Problem
If the starting wall is not straight, the entire floor will be out of alignment. By the time you reach the opposite wall, the discrepancy can be pronounced and very visible, especially if the planks are a uniform colour.
The Fix
Measure from the starting wall at multiple points to check for straightness. If the wall is out of square, snap a chalk line parallel to the room’s longest dimension and start from that line. Rip the first row of planks to follow the wall’s contour while keeping the leading edge straight.
Mistake 10: Ignoring the Direction of Light
The Problem
Laying planks perpendicular to the main light source can emphasise seams and make joints more visible. This is especially noticeable with lower-quality laminate or in rooms with large windows and lots of natural light.
The Fix
Run planks parallel to the longest wall and in the direction of the primary light source (usually toward the main window). This makes seams less visible and creates a more cohesive look. In hallways, always run planks lengthwise.
Mistake 11: Installing Laminate in Wet Areas Without Protection
The Problem
Standard laminate is not waterproof. The HDF core absorbs water through exposed edges and seams. Installing laminate in bathrooms, laundry rooms, or near exterior doors without protection leads to swelling and irreversible damage.
The Fix
In moisture-prone areas, choose a water-resistant laminate with sealed edges and a hydrophobic core, or switch to a fully waterproof flooring material like luxury vinyl plank or SPC. If you install laminate in a kitchen, use mats near the sink and dishwasher and clean up spills immediately.
Mistake 12: Not Leaving Transition Strips
The Problem
Running laminate continuously through doorways and between rooms without transition strips means the floor has no expansion break. In long runs, this leads to buckling because the laminate cannot expand and contract freely.
The Fix
Install T-moulding transition strips at every doorway where the floor passes between rooms. Break the floor at doorways to create independent floating sections. This is especially important in homes with large open floor plans.
Mistake 13: Using the Wrong Cleaning Products
The Problem
Steam mops, soaking-wet mops, vinegar, and abrasive cleaners all damage laminate. Steam forces moisture through the seams, vinegar dulls the finish over time, and abrasive products scratch the wear layer.
The Fix
Use a dry or slightly damp microfibre mop with a cleaner specifically formulated for laminate floors. Spray the cleaner onto the mop, not directly onto the floor. Less moisture is always better with laminate.
Mistake 14: Not Checking Planks for Defects
The Problem
Manufacturing defects — chipped edges, colour mismatches, warped planks — happen. If you install a defective plank, you will have to disassemble rows to replace it later.
The Fix
Inspect each plank before installation. Check for chips, cracks, colour consistency, and warping. Mix planks from multiple boxes to distribute any slight variation in shade. Set aside any damaged pieces for cuts or return.
Mistake 15: Pinning the Floor Down
The Problem
Nailing, screwing, or gluing laminate to the subfloor prevents it from floating freely. Heavy furniture or appliances placed directly on the laminate without clearance can have the same effect. The floor buckles because it cannot move.
The Fix
Never fasten laminate to the subfloor. Ensure heavy items like kitchen islands and built-in bookcases are installed before the laminate, with the laminate run up to (but not under) them. Leave the floor free to float.
Frequently Asked Questions
Can I lay laminate over old vinyl flooring?
Yes, as long as the vinyl is firmly bonded, smooth, and level. Remove any loose or cushioned vinyl first. Use a standard underlayment on top of the vinyl.
How long should laminate acclimatise?
A minimum of 48 hours is the general recommendation. In extreme climate differences (e.g., the laminate was stored in an unheated warehouse and your home is fully heated), allow 72 hours or more.
What happens if I do not leave an expansion gap?
The floor will buckle — planks will lift away from the subfloor, creating visible peaks along the joints. Fixing this requires removing the baseboards, trimming the edges, and reinstalling the moulding.
Is laminate harder to install than vinyl plank?
They are comparably easy. LVP flooring is slightly more forgiving because it is flexible and can tolerate minor subfloor imperfections. Laminate is rigid and less tolerant of an uneven surface. Both use click-lock systems.
Final Thoughts
Laying laminate flooring is a rewarding DIY project when done correctly. The key is patience and preparation. Acclimatise your planks, prepare your subfloor meticulously, maintain expansion gaps religiously, and take the time to stagger joints and undercut door frames. Avoid these common mistakes and your laminate floor will look professional, feel solid, and perform beautifully for years to come.
Prefer to explore on your own?
See how new flooring looks in your actual room in seconds — free, no signup.
Try the free Floor Studio →