Picking the right service size used to be simple — a 100-amp panel covered most three-bedroom homes for decades. That math broke when EVs, heat pumps, induction ranges, and on-demand water heaters started showing up in the same households. Electrical panel sizes available today range from 60-amp to 400-amp, and choosing right depends on a real load calculation, not a contractor’s eyeball estimate. This guide walks through every common size, how to calculate what your home actually needs, and where the smart money sits in 2026.
The Common Service Sizes
Residential panels come in standardized amperage ratings: 60, 100, 125, 150, 200, 300, 320, and 400 amps. The most common in US homes today are 100A and 200A, with 200A increasingly the default for new construction in most states. Larger services (320 and 400 amps) appear in homes over 3,500 sq ft, properties with detached structures, or homes adding multiple EV chargers and a heat pump simultaneously.
- 60-amp: Pre-1965 homes, small apartments. Cannot legally power modern electric ranges plus central AC simultaneously
- 100-amp: Most 1970s to 1990s homes under 2,000 sq ft with gas heat and gas water heater
- 125-amp: Slightly upgraded 100A; uncommon, used in light remodels
- 150-amp: Mid-size homes with mixed gas/electric. Allows 1 EV charger comfortably
- 200-amp: The current new-construction default. Handles all-electric 2,500 to 3,500 sq ft home with EV charger and heat pump
- 320/400-amp: Large homes, ADUs, workshops, or households planning two EVs plus full electrification
Running the Load Calculation
NEC Article 220 spells out the load calc. The standard method adds general lighting (3 watts per sq ft of habitable space), small appliance circuits (1,500 watts each, minimum two), laundry (1,500 watts), all fixed appliances at nameplate, and the largest of heating or cooling load. Apply the demand factors (100 percent of first 10,000 watts, then 40 percent of the remainder for general loads), divide by 240V, and you have your minimum service amperage.
A 2,400 sq ft home with electric range (12 kW), electric dryer (5.5 kW), central AC (5-ton, 24 amps at 240V = 5.76 kW), gas heat, and a Level 2 EV charger (40 amps continuous = 9.6 kW) calculates to roughly 145 amps demand. That comfortably fits a 150A service today but leaves little headroom for a future heat pump conversion. Result: go 200A.
When to Upgrade and Why
Four signals indicate it’s time to upgrade your service. First, a panel that constantly trips breakers under normal use — usually a 100A on a 2,500 sq ft home with too many modern appliances. Second, no space for new circuits and the panel is already running tandem breakers in slots not rated for them. Third, installation of a Level 2 EV charger (typically 40 to 60 amps continuous). Fourth, switching from gas to electric on major appliances — heat pump replacing furnace, induction range replacing gas, heat pump water heater replacing gas tankless.
The other reason to upgrade is age. Federal Pacific Stab-Lok and Zinsco panels fail to trip at high overloads and are essentially uninsurable in many states. If you have one, the panel goes regardless of amperage demand.
The Real Cost of Each Upgrade
Upgrading is rarely just the panel itself. The full project includes the service mast, weatherhead, meter base, grounding electrode system, and often the utility company’s overhead drop or underground service lateral.
- 100A panel replacement (same amperage): $1,200 to $2,400
- 100A to 200A upgrade with new service entrance: $2,800 to $4,500
- Underground service lateral replacement (utility coordination): add $1,500 to $4,000
- 200A to 320A or 400A upgrade: $4,500 to $8,500
- Detached structure subpanel (100A): $1,800 to $3,800 depending on trenching
- Permits and inspection: $80 to $400 typical
Top Panel Brands
The four major US panel manufacturers are Square D, Eaton, Siemens, and General Electric (now ABB). All produce code-compliant gear, but they differ in breaker availability, slot count, and integrated surge protection.
Square D Homeline (HOM series) is the homeowner standard at $145 to $310 for a 200A 40-space panel. Square D QO is the contractor-grade upgrade with visible trip indicators ($380 to $560). Eaton CH series competes directly with QO at $410 to $590, with excellent AFCI and GFCI breaker availability. Siemens PL series runs slightly cheaper at $130 to $280 for a 200A 40-space. Avoid Federal Pacific (out of production but still found in older homes), Zinsco, and Pushmatic — all have documented failure issues.
Smart Panels Worth Considering
Smart panels integrate per-circuit monitoring, remote control, and load management directly into the panel itself. The Span Drive ($3,500) replaces a standard 200A panel with a fully digital unit that lets you turn circuits on and off from a phone app. Schneider Electric Wiser Energy Center and Lumin Smart Panel offer similar functionality at $2,800 to $4,200.
The smart panel sweet spot is for homes that cannot easily upgrade their service. A smart panel lets you stay on a 150A or 200A service while adding EV charging, by automatically shedding lower-priority circuits when the EV draws full power. This is especially valuable in older homes where upgrading the underground service costs $6,000 or more.
Future-Proofing the Choice
Three modern loads dominate sizing decisions. A Level 2 EV charger pulls 30 to 50 amps continuous. A heat pump for a 2,000 sq ft home pulls 25 to 40 amps in heating mode. An induction range pulls 40 to 50 amps peak. Combined, that’s 95 to 140 amps of new load on top of existing house demand. Plan accordingly.
The general rule for new builds and major renovations: install 200A minimum, even in smaller homes. The cost premium over 100A is modest ($300 to $500 in materials), and the upgrade cost later is multiples of that. For homes over 3,500 sq ft or with planned dual EVs, jump to 320A or two 200A panels in tandem.
Working With the Utility
Most service upgrades require coordination with your utility company. The utility owns the service drop, meter, and the cable up to the meter base. You own everything downstream. A 200A upgrade typically requires the utility to pull the meter, the electrician to swap the panel and meter base, and the utility to re-energize the service. Expect 2 to 5 hours of total downtime on install day.
Schedule this in mild weather. A panel upgrade in January with a fridge full of food and an outside temperature of 18°F is a recipe for stress. Spring and fall are easier on the family and easier on the inspector’s schedule. Confirm with your electrician whether your jurisdiction requires AFCI and GFCI on all branch circuits per the 2023 NEC — many do, and the breakers add $40 to $60 per circuit to the upgrade bill.