Wall-hung vanities have quietly become the most-requested upgrade in modern bathroom remodels, and for good reason: they make a small room feel bigger by showing off the floor beneath them. Buying a floating bathroom vanity cabinet only — the base cabinet without a pre-attached top or sink — gives you the freedom to pair it with the exact countertop, sink, and faucet you want. That flexibility is the whole point, but it also means you need to understand mounting, sizing, and plumbing before you order.
Part of our Bathroom Remodeling & Flooring guide — explore the full guide →
What “Cabinet Only” Actually Means
When a listing says cabinet only, you are buying the wall-mounted box and its doors or drawers, and nothing else. There is no countertop, no sink basin, no faucet, and usually no mirror. You supply those separately. This appeals to homeowners who already have a specific quartz remnant, a vessel sink they love, or a custom stone top in mind.
The alternative is an all-in-one vanity where the top and integrated sink arrive attached or pre-cut to fit. Cabinet-only costs less up front and offers far more design control, but it does put the burden of matching dimensions and drilling the top on you or your installer.
Standard Sizes and How to Measure
Floating vanity cabinets come in the same nominal widths as traditional ones, so planning is straightforward. Common widths are 24, 30, 36, 48, and 60 inches, with 72-inch doubles for large bathrooms. Depth typically runs 18 to 21 inches, and floating units are often shallower — 18-inch depth is popular in tight powder rooms.
Height is where floating vanities differ most. Because they mount to the wall, you choose the installed height rather than accepting a fixed toe-kick. Standard countertop height lands at 32 to 36 inches from the floor. Measure these before you buy:
- Available wall width — leave at least 2 to 4 inches of clearance on each side for trim and swing room
- Rough-in plumbing height — where the water supply and drain exit the wall
- Door swing and traffic path — make sure the vanity does not block the door
Because the cabinet floats, your drain and supply lines must exit the wall high enough to sit behind the cabinet rather than the floor. Many remodels require moving the plumbing to a wall rough-in, which is the single biggest hidden cost of going floating.
Why Mounting Is Everything
A floating vanity carries its full weight, plus a stone top and a basin full of water, on the wall alone. That load can easily exceed 150 pounds. You cannot hang that on drywall anchors and hope for the best. Proper installation demands either lag bolts driven into wall studs or, ideally, solid blocking installed inside the wall before the drywall goes up.
If your studs do not line up with the cabinet’s mounting rail, add a horizontal 2×8 or 2×10 blocking board between studs during a remodel. Then the vanity’s cleat or French-cleat system bolts into continuous solid wood. Skip this step and the cabinet will sag, pull loose, and crack the wall over time.
Choosing a Top and Sink
With cabinet-only, the top is your call. Popular pairings include:
- Quartz or granite with an undermount sink: the most durable and seamless look, cut to fit at a stone shop
- Solid-surface (Corian-style) integrated top: sink and counter in one molded piece, easy to clean
- Vessel sink on a solid wood or quartz slab: a bold, modern statement that sits above the counter
- Prefab vanity tops: budget-friendly cultured marble tops pre-drilled for a faucet
Match the top’s depth and width to the cabinet, and confirm the faucet hole spacing before you drill. For vessel sinks, remember the total height climbs several inches, so mount the cabinet a bit lower than usual.
What It Costs
Prices vary widely by material and brand. A budget MDF or laminate floating cabinet-only starts around $200-$400. Mid-range plywood boxes with soft-close hardware run $500-$1,000. Solid wood or designer European units can exceed $1,500 for the cabinet alone. Then add:
- Countertop: $150-$600 depending on material and size
- Sink and faucet: $80-$400 combined
- Mounting hardware and blocking: $30-$80
- Plumber to relocate rough-in: $300-$800 if lines must move
A complete DIY floating vanity project typically lands between $600 and $2,000, well under the cost of a custom built-in.
Pros and Cons at a Glance
Floating vanities look sleek and make cleaning the floor effortless, since there is no toe-kick to trap dust. They visually enlarge small bathrooms and let you set an ergonomic height. On the downside, they demand solid wall support, storage space is slightly reduced because there is no floor base, and moving plumbing adds cost. For homes with a wet, mop-heavy bathroom floor, keeping electronics and wood off the ground is a genuine practical bonus.
Installation Tips From the Field
A few habits separate a clean install from a crooked one. Find and mark every stud, then transfer the cabinet’s mounting height with a long level and a pencil line across the wall. Dry-fit the cabinet against that line with a helper before drilling anything. Use a stud finder to confirm blocking or studs, and always drill pilot holes for lag bolts.
Set the cabinet, check level in both directions, and shim behind the cleat if the wall is uneven. Only after the box is rock-solid should you place the top and connect the sink. Buying a floating bathroom vanity cabinet only rewards patience — get the wall support and plumbing right, and you end up with a custom-looking bathroom for a fraction of custom prices.
Plumbing Rough-In Considerations
Buying the cabinet alone means you also own the plumbing puzzle, and floating vanities change the rules. Because there is no base to hide pipes inside a cabinet toekick, the supply lines and drain must exit the wall, not the floor. If your existing rough-in comes up through the subfloor, budget for a plumber to move it into the wall cavity before the cabinet goes up — that is often a $300 to $600 add depending on wall access and whether tile has to come off.
Mounting height affects the drain, too. A standard wall drain sits around 18 to 20 inches off the finished floor, but a floating vanity hung higher or lower shifts that target. Dry-fit the cabinet, mark where the drain and stops will land, and confirm the P-trap clears the back panel and any drawers. Many cabinet-only floating units use a shallow drawer with a U-shaped notch cut around the plumbing, so check that the notch lines up with your actual pipe location before you commit.
Frequently Asked Questions
Can a floating vanity hold a stone countertop?
Yes, as long as it is anchored into solid blocking or studs. A properly mounted 36-inch cabinet easily carries a quartz or granite top plus a vessel sink. The load rides on the wall framing, not the cabinet box alone, so the blocking behind the drywall is what really matters.
What height should I hang it?
Standard comfort height puts the finished countertop around 32 to 36 inches off the floor. Floating units give you freedom here, so match it to the primary users. Hanging the cabinet with 8 to 12 inches of open floor below keeps the light, airy look these vanities are prized for.
Do I need special mounting hardware?
Heavy-duty French cleats or a manufacturer-supplied mounting rail lagged into studs is the standard. Never rely on drywall anchors alone. If the studs do not fall where you need them, add horizontal 2x blocking inside the wall before you close it up.
Can I install one myself?
A confident DIYer can hang the cabinet, but moving the plumbing rough-in into the wall is usually a job for a licensed plumber unless you are comfortable soldering or working with PEX and know your local code.